Anritsu MS2690 User manual

Document No.: M-W2853AE-32.0
ANRITSU CORPORATION
•
For safety and warning information, please read this
manual before attempting to use the equipment.
•
Additional safety and warning information is provided
within the MS2690A/MS2691A/MS2692A Signal
Analyzer Operation Manual (Mainframe Operation),
MS2830A Signal Analyzer Operation Manual
(Mainframe Operation) or MS2840A Signal Analyzer
Operation Manual (Mainframe Operation). Please also
refer to this document before using the equipment.
•
Keep this manual with the equipment.
MS2690A/MS2691A/MS2692A
and MS2830A/MS2840A
Signal Analyzer
Operation Manual
Signal Analyzer Function
Remote Control
32th Edition

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following
safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the
symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu equipment.
In addition, there may be other labels attached to products that are not shown in the diagrams in this manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is indicated
symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer
Operation Manual Signal Analyzer Function Remote Control
25 April 2007 (First Edition)
20 October 2016 (32th Edition)
Copyright © 2007-2016, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

iii
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's
country of origin for re-
export from your
country.
Before re
-
exporting the product or manuals, please contact us to confirm
whet
her they are export-controlled items or not.
When you dispose of export
-
controlled items, the products/manuals need to
be broken/shredded so as not to be unlawfully used for military purpose.

iv

I
About This Manual
Operation manual configuration
The operation manual configuration of the MS2690A/MS2691A/MS2692A,
MS2830A and MS2840A Signal Analyzer is shown below.
MS2690A/MS2691A/MS2692A Signal Analyzer Operation Manual
(
Main Frame O
p
eration
)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Phase Noise Measurement Function Operation)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Main Frame Remote Control)
MS2840A Signal Analyzer Operation Manual
(Main Frame Operation)
Or MS2830A Signal Analyzer Operation Manual
(
Main Frame O
p
eration
)
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control)
MS2830A/MS2840A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
Or
MS2690A/MS2691A/MS2692A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)
MS2830A/MS2840A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
Or

II
Signal Analyzer Operation Manual (Mainframe Operation)
Signal Analyzer Operation Manual (Mainframe Remote Control)
Description of basic operations, maintenance procedures, common
functions and common remote functions of the mainframe
Signal Analyzer Operation Manual (Signal Analyzer Function)
Signal Analyzer Operation Manual (Signal Analyzer Function Remote
Control) <This document>
Description of basic operations, functions and remote functions of the
signal analyzer
Signal Analyzer Operation Manual (Spectrum Analyzer Function)
Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote
Control)
Description of basic operations, functions and remote functions of the
spectrum analyzer
Signal Analyzer Operation Manual (Phase Noise Measurement Function)
Signal Analyzer Operation Manual (Phase Noise Measurement Function
Remote Control)
Description of basic operations, common functions and common
remote functions of the Phase Noise Measurement function
Convention Used in This Manual
Except where there is a good reason to do otherwise, this manual
assumes the use of MS269xA.
Note that the descriptions in this manual also apply to MS2830A or
MS2840A.

1
III
2
3
4
Table of Contents
About This Manual........................................ I
Chapter 1 Overview.................................... 1-1
1.1 Overview .................................................................... 1-2
Chapter 2 SCPI Device Message Details.. 2-1
2.1 Frequency Settings.................................................... 2-19
2.2 Level Settings ............................................................ 2-45
2.3 Trigger Settings.......................................................... 2-60
2.4 Capture Setting.......................................................... 2-86
2.5 Marker Settings.......................................................... 2-110
2.6 Signal Search Settings .............................................. 2-161
2.7 Trace Settings............................................................ 2-183
2.8 Measure Common Function Settings ........................ 2-292
2.9 Adjacent Channel Power Measurement Settings ...... 2-304
2.10 Channel Power Measurement Settings ..................... 2-382
2.11 Occupied Bandwidth Measurement Settings............. 2-421
2.12 Burst Average Power Measurement Settings............ 2-454
2.13 AM Depth Measurement Settings.............................. 2-475
2.14 FM deviation Measurement Settings ......................... 2-480
2.15 DigRF 3G Settings..................................................... 2-485
2.16 Setting Replay function.............................................. 2-506
2.17 Sub Trace Settings .................................................... 2-514
2.18 Other Function Settings ............................................. 2-534
2.19 QUEStionable Status Register .................................. 2-556
2.20 OPERation Status Register ....................................... 2-566
2.21 Batch Processing Function Setting............................ 2-573
2.22 Setting External Mixer................................................ 2-579
2.23 FM CW Measurement Settings.................................. 2-587

IV.
Chapter 3 Native Device Message List..... 3-1
3.1 IEEE488.2 Common Device Messages .................... 3-2
3.2 Application Common Device Messages .................... 3-4
3.3 Frequency/Time Settings........................................... 3-7
3.4 Level Settings ............................................................ 3-8
3.5 Measurement/Trigger Settings .................................. 3-9
3.6 Common Settings for Each Trace.............................. 3-10
3.7 Spectrum Trace Settings ........................................... 3-11
3.8 Power vs Time Trace Settings................................... 3-22
3.9 Frequency vs Time Trace Settings............................ 3-27
3.10 CCDF Trace Settings................................................. 3-31
3.11 Spectrogram Trace Settings ...................................... 3-40
3.12 DigRF 3G Measurement Settings.............................. 3-42
3.13 Waveform Data Saving Function Settings................. 3-44
3.14 Replay Function Settings........................................... 3-45
3.15 Sub Trace Settings .................................................... 3-47
3.16 Reference Signal Settings ......................................... 3-49
3.17 Power Adjustment...................................................... 3-50
3.18 Other Settings ............................................................ 3-51
3.19 Setting External Mixer................................................ 3-52
Chapter 4 Native Device Message Details 4-1

Chapter 1 Overview
1-1
1
Overview
This chapter provides an overview of the remote control of the Spectrum
Analyzer function (hereinafter, referred to as “this application”).
1.1 Overview .................................................................... 1-2

Chapter 1 Overview
1-2.
1.1 Overview
Automatic measurement can be performed by using this instrument in
connection with an external controller (PC). This instrument is
standardly equipped with GPIB, Ethernet, and USB interfaces. You can
also select a remote control command from the SCPI mode, which is a
command format defined by the SCPI Consortium, and Native mode,
which is our unique format.
See the
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A Signal
Analyzer Operation Manual (Mainframe Remote Control)
for how to
switch the language mode.
You can use the Native mode by converting SCPI commands into Native
ones. See the
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Mainframe Remote Control)
for
details.
To use the Signal Analyzer function on the MS2830A or MS2840A,
Analysis Bandwidth 10 MHz Option or greater is required.