ANTAIRA APN-210N User manual

1
Industrial Wireless-N Access Point
APN-210N
User Manual
Version 1.2

2
© Copyright 2013 Antaira Technologies, LLC
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction,
adaptation or translation without prior permission is prohibited, except as allowed under the
copyright laws.
Trademark Information
Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the
Windows logo are the trademarks of Microsoft Corp. NetWare is the registered trademark of
Novell Inc. WMM and WPA are the registered trademarks of Wi-Fi Alliance. All other brand and
product names are trademarks or registered trademarks of their respective owners.
Notice: Copyrights © 2013 by Antaira Technologies, LLC. All rights reserved. Reproduction,
adaptation, or translation without prior permission of Antaira Technologies, LLC is prohibited,
except as allowed under the copyright laws.
Disclaimer
Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or
implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. Antaira Technologies, LLC may make improvements and/or changes to
the product and/or specifications of the product described in this manual, without prior notice.
Antaira Technologies, LLC will not be liable for any technical inaccuracies or typographical
errors found in this guide. Changes are periodically made to the information contained herein
and will be incorporated into later versions of the manual. The information contained is subject
to change without prior notice.

3
FCC NOTICE
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This device generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Connect the computer to an outlet on a circuit different from that to which the receiver is
connected.
•Increase the separation between the computer and receiver.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause
undesired operation.
RF Exposure warning
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any other antenna or
transmitter.
ICES 003 Statement
This Class B digital apparatus complies with Canadian ICES-003.

4
Declaration of Conformity
Antaira declares the following:
Product Type: Wireless Access Point
Model No.: APN-210N conforms to the following Product Standards:
This device complies with the Electromagnetic Compatibility Directive (89/336/EEC) issued by
the Commission of the European Community. Compliance with this directive implies conformity
to the following European Norms (in brackets are the equivalent international standards.)
Electromagnetic Interference (Conduction and Radiation): EN 55022 (CISPR 22)
Electromagnetic Immunity: EN 55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11)
Low Voltage Directive: EN 60 950: 1992+A1: 1993+A2: 1993+A3: 1995+A4: 1996+A11: 1997.
Therefore, this product is in conformity with the following regional standards: FCC Class B:
following the provisions of FCC Part 15 directive, CE Mark: following the provisions of the EC
directive.
Antaira also declares that:
The wireless card in this product complies with the R&TTE Directive (1999/5/EC) issued by the
Commission of the European Community. Compliance with this directive implies conformity to
the following:
EMC Standards: FCC: 47 CFR Part 15, Subpart B, 47 CFR Part 15, Subpart C (Section 15.247); CE:
EN 300 328-2, EN 300 826 (EN 301 489-17)
Therefore, this product is in conformity with the following regional standards: FCC Class B:
following the provisions of FCC Part 15 directive, CE Mark: following the provisions of the EC
directive.
Manual Version:1.12 (January 2013)
This manual is written based on Firmware version 1.26

5
Table of Contents
Overview.........................................................................................................7
Introduction....................................................................................................7
Features and Benefits....................................................................................................8
Hardware Installation.....................................................................................9
DIN-Rail Installation.......................................................................................9
Wall Mount Installation.................................................................................................10
Hardware Overview......................................................................................11
Front Panel....................................................................................................................11
Front Panel LEDs.........................................................................................................12
Top Panel.......................................................................................................................12
Rear Panel.....................................................................................................................13
Cables and Antennas...................................................................................14
Ethernet Cables............................................................................................................14
10BaseT/100BaseTX PinAssignments....................................................................14
Wireless Antenna..........................................................................................................15
Operation Modes & Connection Examples................................................16
Access Point and Access Point WDS Mode ............................................................16
Access Point WDS Mode............................................................................................16
Station Mode.................................................................................................................17
Station WDS Mode.......................................................................................................18
Repeater WDS Mode...................................................................................................19
Configure the IP Address............................................................................19
For Windows 95/98/98SE/ME/NT..............................................................................20
For Windows XP/2000.................................................................................................21
Access the Web Interface............................................................................23
Access with uConfig.....................................................................................................23
Access with Web Browser...........................................................................................26
Navigation ....................................................................................................29
Main Menu Bar..............................................................................................................29
How to save changes ..................................................................................................29
Basic Network Tab.......................................................................................30
Network Mode: Bridging..............................................................................................30
LAN Setup.....................................................................................................................30
Basic Wireless Tab ......................................................................................33
Basic Wireless Settings...............................................................................................33
Wireless Mode..............................................................................................................33
Access Point Parameters Settings ............................................................................34
Station Parameters Settings.......................................................................................36
Wireless Security..........................................................................................................38
Virtual Access Point (VAP)..........................................................................................43

6
Advance Wireless Tab.................................................................................44
Long Range Parameters Setup..................................................................................44
Services Tab.................................................................................................46
Ping Watchdog..............................................................................................................47
Auto-Reboot..................................................................................................................47
SNMP Setup..................................................................................................................48
NTP Setup.....................................................................................................................48
Web HTTP Security......................................................................................................48
TelnetAccess Setup.....................................................................................................49
SSH Access Setup.......................................................................................................49
System Log Setup........................................................................................................49
System Tab...................................................................................................50
Firmware Upgrade........................................................................................................50
Host Name.....................................................................................................................51
Administrative and Read-only Account.....................................................................51
Configuration Management.........................................................................................52
Device Maintenance ....................................................................................................52
Status Page ..................................................................................................54
Status Reporting...........................................................................................................54
Station Connection Info...............................................................................................56
More Status...................................................................................................................58
VLAN Tab......................................................................................................59
VLAN Switch.................................................................................................................59
VLAN Management......................................................................................................60
Appendix I - Network ...................................................................................61
Appendix II- Advanced Settings .................................................................64
Appendix III- Services..................................................................................67
Appendix IV- VLAN Setup examples..........................................................69
A) Tagged Wireless VLAN to Tagged Ethernet VLAN Setup.................................69
B) Untagged Wireless VLAN to Tagged Ethernet VLAN setup .............................70
C) Tagged VLAN Pass-Through.................................................................................70

7
Overview
Introduction
The high-performance Wireless NetworkAccess Point (AP) is designed for industrial and
enterprise access applications. Embedded with the Atheros chipset, it boasts network
robustness, stability and wider network coverage. Based on 802.11n (Draft 2.0), the
access point supports high-speed data transmission of up to 300Mbps.
The access point is capable of operating in different modes, which makes it suitable for a
wide variety of wireless applications, including long-distance deployments.
Designed with externals R-SMAconnectors offering excellent electrical performance and
compatible with R-SMA antennas, the access point can be used for a wide variety of
wireless applications and allows you to position the wireless antenna in a better
signal-broadcasting location for improved wireless coverage and signal strength or simply
in a more convenient location.
To protect your security and privacy, the access point is armed with many enhanced and
latest wireless security features such as IEEE 802.11i standards, MACAddress Filtering,
IEEE 802.1xAuthentication and WEP/WPA/WPA2 encryption to ensure privacy for the
heterogeneous mix of users within the same wireless network.
The access point also incorporates a unique set of advanced features such as: VirtualAP
to deliver multiple services; Long-Range parameter fine-tuning which provide the access
point with the ability to auto-calculate parameters such as slot time,ACK time-out and
CTS time-out to achieve a longer range.

8
Features and Benefits
Point-to-Point & Point-to-MultiPoint Support
Point-to-Point and Point-to-MultiPoint communication between different buildings enables
you to bridge wireless clients that are kilometres apart while unifying the networks.
Virtual AP (Multiple SSID)
Virtual AP implements mSSID (Multi-SSID) This allows a single wireless system to be set
up with multiple virtual AP connections with different SSIDs or BSSID (Basic Service Set
Identifier) and different security settings.
Highly Secured Wireless Network
The access point supports the highest available wireless security standard: IEEE802.11i
compliant. The access point also supports IEEE 802.1x for secure and centralized
user-based authentication. Wireless clients are thus required to authenticate through
highly secure methods like EAP-TTLS and EAP-PEAP, in order to obtain access to the
network.
uConfig Utility
The exclusive uConfig utility allows users to access the user-friendly Web configuration
interface of the access point without having to change the TCP/IP setup of the
workstation.
HTTPS
The access point supports HTTPS (SSL) in addition to the standard HTTP.
HTTPS (SSL) features additional authentication and encryption for secure
communication.
Telnet
Telnet allows a computer to remotely connect to the access point CLI (Command Line
Interface) for control and monitoring.
SSH
SSH (Secure Shell Host) establishes a secure host connection to the access point
CLI for control and monitoring

9
Hardware Installation
DIN-Rail Installation
Each AP has a DIN-Rail kit on rear panel. The DIN-Rail kit helps AP to fix on the DIN-Rail. It
is easy to install the AP on the DIN-Rail:
Step 1: Slant the AP and mount the metal spring to DIN-Rail.
Step 2: Push the AP toward the DIN-Rail until you heard a “click” sound.

10
Wall Mount Installation
Each AP has another installation method to fix the AP. Awall mount panel can be found in the
package. The following steps show how to mount the AP on the wall:
Step 1: Remove DIN-Rail kit.
Step 2: Use 6 screws that can be found in the package to combine the wall mount panel.
* The screws specification shows in the following two pictures. In order to prevent the
AP from any damage, the screws should not be larger than the size of that used in the
APN-210N.
Pozidrive
Step 3: Mount the combined AP on the wall.