Antrica ANT-39000 User manual

Antrica Quick Start Guide
ANT-39000 Series V230619
Page 1
ANT-39000 QUICK START GUIDE
Applicable to ANT-39000

Contents
1 Whats in the box
2 Setting up the ANT-39000
3. Configuring the ANT-39000
3.1 Video Information
3.2 Video Encode
3.3 Network & IP Port
4. Streaming
4.1 RTSP over TCP to VLC player
4.1.1 How to configure VLC
4.2 MPEG Transport Stream to VLC
4.3 How to open an RTMP stream
5. Help and Further Support
5.1 ONVIF Support
5.2 Other Information
1.What’s in the Box
The ANT-39000 box contains
- ANT-39000 encoder
-12 Volt Power converter (requires an IEC AC mains lead)
-UK/EU/USA or China IEC 110/240v AC Lead (depending on your location)
-Fixing brackets
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 2

2. Setting up the ANT-39000
Connect the ANT-39000 to a laptop or PC via an Ethernet switch using standard
ethernet cables.
Connect the input Video source using an HDMI cable Connect the 12 volt power
input (or use PoE )and switch on.
The ANT-39000 will take approximately 1 minutes to boot up. You will see 4 LEDs.
On powering the Red power LED is ON, after boot up the Green Status LED will
flash. The status of these LEDs is described in the table at the end of this guide
You are now ready to setup the ANT-39000 Encoder
3. Configuring the ANT-39000
The ANT-39000 default IP address is 192.168.10.100 . Please set the laptop/PC
Ethernet IP address to be in the same sub-domain e.g 192.168.10.XXX
Open Chrome (this will allow video to be viewed) or other browser to just view
settings and browse to 192.168.10.100
You will be asked to LOGIN: User : admin , password: 1234
Please Note! There is a SETUP button top right in the first web page :Click
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 3
SETUP

3.1 Video Information
The Video Information page shows if a valid video signal is connected and gives
information about the stream settings.
3.2 Video Encode:Settings
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 4
Input format HDMI
only for ANT-39000
Input
format
Detected in Auto
Mode
Primary
Stream settings
3 other tabs for
stream 2-4

3.3 Network- IP & Port:
This section allows you set the encoder IP address and other network items
4.Streaming :
This section explains how to stream the following formats to VLC player as an
example player. Settings may vary with other players
4.1 RTSP over TCP to VLC player:
RTSP streaming only requires one setting to be changed in the ANT-38500. This is
the RTSP port which can be found under Network-IP&Port. By default this Port 554
The ANT-38500 RTSP URL is as follows:
rtsp://<IP ADDRESS>:<PORT>/video1 (video only streaming of primary stream)
rtsp://<IP ADDRESS>:<PORT>/video1s (video only streaming of 2nd stream)
rtsp://<IP ADDRESS>:<PORT>/video1s1 (video only streaming of 3rd stream)
rtsp://<IP ADDRESS>:<PORT>/video1s2 (video only streaming of 4th stream)
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 5
Network
Settings

Port is 554 in this case
If audio is required the URL adds +audio1 (audio1s or audio1s1 or audio1s2)
e.g rtsp://user:password@<IP ADDRESS>:<PORT>/video1s1+audio1s1 (video +
audio streaming of third stream) the audio URL extension always follows the video
URL . User:password@ use if authenticated (remove if not authenticated)
Primary 2nd, 3rd and 4th steams are setup in the Video Encode section.
4.1.1 How to Configure VLC Player
Open VLC player and select FILE / OPEN NETWORK . Note the input windows in
VLC may vary depending on which operating system you are running VLC on.
This example is the MAC OS X Version of VLC player.
Type in the RTSP URL with Port number as shown in this example:
rtsp://admin:[email protected]:554/video1+audio1
Click OPEN…you should see the video stream displayed
If a user name and password box pops up the RTSP is Authenticated and needs
user and password. To add user name and user password in the RTSP URL please
enter this URL in VLC player : rtsp://
username:password@<IP address>:<port>/
video1
NOTE! In advanced settings you will find
VLC has a default buffer setting of 1000mS
this can be lowered to reduce latency to
around 100-200mS
4.2 MPEG Transport Stream over UDP
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 6

To stream MPEG TS first we need to setup ONE WAY STREAMING in the
ANT-38500 which can be found under NETWORK-One way streaming.
Select MPEG TS and click Apply . Here you can select and Enable any or all of the 4
streams. There are two settings:
IP Address: This is either the destination Unicast IP address of the computer on
which VLC is running or the multicast IP address you wish to use.
Port: This is the port you wish to use for streaming
Note! If you want to stream MPEG-TS over the internet you must use the single
Public IP address of the building in which the computer, running VLC, is located. The
Router in this building will need to PORT FORWARD this stream( port number
chosen above) to the internal IP address of the computer. Further data on Port
Forwarding and Router setup contact [email protected] . Multicast is not
supported over the Internet.
4.2.1 Open an MPEG-TS stream in VLC
Open VLC and open File/Network Please note the unicast URL has no IP in it.
Example URL for MPEG Transport Stream
udp://@:1234 (unicast)
udp://@227.2.2.7:1234 (Multicast)
4.3 Open an RTMP stream
To stream RTMP you will need to know two pieces of information:
RTMP URL : example rtmp://wowza.antrica.com:1935/live/
Stream Name: streamdemo
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 7

Complete URL would then be
rtmp://wowza.antrica.com:1935/live/streamdemo
Examples of players will be WOWZA media server or Youtube live streaming . Both
of these players can be setup to generate the full URL
Full URL= [Primary server URL:Port]/[Stream name]
5.0 Help and Further Support
5.1 ONVIF Support
The ANT-39000 series supports ONVIF profile S+G and uses port 80 as standard
and login user name and password (admin: 1234). Profiles are as defined in the 4
stream settings in section 3.2 of this Quick Start Guide.
5.2 Other Information
Please visit our website
www.antrica.com and browse
to the product page (e.g
ANT-38500) where you can
find a DOWNLOADS
SECTION :
- application notes
- Full User manuals
- FAQs
- Firmware
- Other useful information
- More help Open up a
Technical Support Ticket
from the support page.
Contact:
[email protected]
Call : [phone] x3
Antrica Quick Start Guide
ANT-39000 Series V230619
Page 8
LED Status Indicators