Anybus WLAN Access Point IP67 User guide
Anybus
®WLAN Access Point IP67
STARTUP GUIDE
SP2383 EN 1.1 ENGLISH
Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB
of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We,
HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous
product development. The information in this document is subject to change without notice and should not
be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no
responsibility for any errors that may appear in this document.
There are many applications of this product. Those responsible for the use of this device must ensure that
all the necessary steps have been taken to verify that the applications meet all performance and safety
requirements including any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems
that may arise as a result from the use of undocumented features, timing, or functional side effects found
outside the documented scope of this product. The effects caused by any direct or indirect use of such
aspects of the product are undefined, and may include e.g. compatibility issues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular implementation, HMS Industrial Networks
AB cannot assume responsibility for actual use based on these examples and illustrations.
Intellectual Property Rights
HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product
described in this document. These intellectual property rights may include patents and pending patent
applications in the USA and other countries.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
About This Document 3 (12)
1 About This Document
This document describes how to install the Anybus WLAN Access Point IP67
and set up a basic configuration.
For additional documentation and software downloads, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
Document Conventions
The following formatting conventions are used in this document to indicate safety
information and other content of specific importance:
WARNING
This instruction must be followed to avoid a risk of death or serious injury.
Caution
This instruction must be followed to avoid a risk of personal injury.
This instruction must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
This is additional information which may facilitate installation and/or
operation.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Installation 4 (12)
2 Installation
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific, Medical)
band. Make sure that all medical devices used in proximity to this device
meet appropriate susceptibility specifications for this type of RF energy.
This product contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.
Make sure that you have all the necessary information about the capabilities and
restrictions of your local network environment before installation.
For optimal reception, wireless devices require a zone between them clear of
objects that could otherwise obstruct or reflect the signal. A minimum distance of
50 cm between the devices should also be observed to avoid interference.
The Anybus WLAN Access Point IP67 can be screw-mounted onto a stable flat
surface using the included wall mounting plate. It can also be pole-mounted
using the included adjustable steel band straps.
Make sure that the connectors on the bottom panel of the unit are facing
down when installing to prevent water intrusion.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Installation 5 (12)
2.1 Overview
1, 2 Antenna connectors
3Power connector (M12)
4LED indicators
5Reset button
6Ethernet connector (M12)
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Installation 6 (12)
2.2 Wall Mounting
1. Attach the mounting plate to the back of the unit using the 4 included screws.
The plate can be attached vertically or horizontally.
2. Hold the unit upright against the wall and fasten it with 4 screws through the
apertures in the plate.
2.3 Pole Mounting
1. Attach the mounting plate to the back of the unit using the 4 included screws.
The plate can be attached vertically or horizontally.
2. Thread the two supplied metal mounting straps through the large slots on
the mounting plate and then put the straps around the pole.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Installation 7 (12)
2.4 Connectors
2.4.1 Power Connector (M12)
Connecting power with reverse polarity or using the wrong type of power
supply may damage the equipment. Make sure that the power supply is
correctly connected and of the recommended type.
The power connector is a 5-pin A-coded M12 type connector that supports dual
power inputs with a common ground connection.
See also Technical Data, p. 10 regarding power supply requirements.
Pin Function
V1+ Power Input 1 +
V1- Power Input 1 -
V2+ Power Input 2 +
V2- Power Input 2 -
Power Ground
2.4.2 Ethernet Connector (M12)
The Ethernet connector is an 8-pin A-coded M12 type connector. The Ethernet
port supports PoE (Power over Ethernet) compliant with IEEE 802.3af.
Pin Function
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Installation 8 (12)
2.5 LED Indicators
PWR1 Green Power supplied on Power Input 1
PWR2 Green Power supplied on Power Input 2
PoE Green Power supplied on Ethernet port
ETH
Off No LAN
Green LAN link established
Green, flashing LAN traffic
WLAN
Off No WLAN
Green WLAN link established
Green, flashing WLAN traffic
2.6 Factory Reset
To restore the factory default settings, press and hold RESET on the front panel
until the power LED indicator(s) starts to flash, then release the button.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Configuration 9 (12)
3 Configuration
Anybus WLAN Access Point IP67 is configured through a web interface which is
accessed by pointing a web browser to the IP address of the unit. The default IP
address is 192.168.0.2. The computer accessing the web interface must be in
the same IP subnet as the access point.
The web interface is designed for the current stable versions of Internet
Explorer, Chrome, Firefox and Safari. Other browsers may not support the
full functionality of the web interface.
Main Menu
Home Click on Run Wizard for easy configuration.
For manual configuration or to modify the settings applied by
the wizard, use the options in the following menus.
Overview Basic information about the access point and the Ethernet and
wireless networks
Basic Settings Basic settings for the access point and the LAN interface
Wireless Settings Basic settings for the WLAN interface
Advanced
Settings
Advanced settings for the WLAN interface
Event Warning
Settings
Settings for alarm messaging and fault indication
System Status Detailed information about network connections and traffic
Administrator Password settings, configuration backup, unit reset, etc.
Logout Click to log out from the Anybus WLAN Access Point IP67.
See the Anybus WLAN Access Point IP67 User Manual for more information.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Technical Data 10 (12)
4 Technical Data
4.1 Technical Specifications
Order code EU: AWB4003
US: AWB4004
Wireless antenna External (N-type)
Maximum range 400 meters
Wired interface Ethernet
Ethernet port 10/100/1000Base-T(X) Auto MDI/MDX
M12 8-pin female A-coded connector
Power connector M12 5-pin female A-coded connector
(dual power inputs in single connector)
Power supply 2 x 12–48 VDC
Power over Ethernet IEEE 802.3af
Power consumption 9 W
Dimensions (WxHxD) 310 x 87 x 310 mm
Weight 2.56 kg
Operating temperature -25 to +70 °C
Storage temperature -40 to +85 °C
Humidity 5 % to 95 % non-condensing
Mounting Wall mount or pole mount
Housing Metal
Protection class IP67
Certifications See datasheet
For more technical details and specifications, visit www.anybus.com/support.
Disposal and recycling
You must dispose of this product properly according to local laws and
regulations. Because this product contains electronic components, it
must be disposed of separately from household waste. When this
product reaches its end of life, contact local authorities to learn about
disposal and recycling options, or simply drop it off at your local HMS
office or return it to HMS.
For more information, see www.hms-networks.com.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
Technical Data 11 (12)
4.2 Dimensions
All measurements are in mm.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 EN 1.1
last page
© 2018 HMS Industrial Networks
Box 4126
300 04 Halmstad, Sweden
Table of contents
Other Anybus Wireless Access Point manuals
