Anzzi CS-FRKD00 Series User manual

DON’T WAIT!
REGISTER NOW!
Register your product within 90 days to ensure your product is
recognized as an official purchase and is eligible for warranty
coverage.
Mail in the completed registry card (Pg. 2) or register online
at www.swcorp.com/register .
Item: CS-CTRCS00WH
CS-FRKD00**
CONSOLE SINK
INSTALL & OPERATION MANUAL
V1.0

Have questions? Call us at or visit us at 1-844-44-ANZZI www.ANZZI.com
PRODUCT REGISTRATION∗
IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS
FULLY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED.
To ensure that your warranty is registered and confirmed please do one of the following:
1. Register online at www.swcorp.com/register. You will be asked to fill out the same
information you would in the registration card. Registering online is fast, secure and
ensures we receive your information.
2. Complete, cut-out and mail the registration card below.By returning this registration
card we confirm the date of purchase for your new product. This confirmation will allow
us to process any warranty claims.
Mail the card to: 5701 NW 35 Avenue, Miami, FL 33142
Product Registration Card
Name
..................................................................................... Address ...........................................................................................................................
City ............................................... State ........................... Zip ..............................
Phone ........................................... Email ........................... .........................................
Date of Purchase ...........................
Installer’s Name ..................................................................... Phone ................................................................................
I have read the Owner’s Manual carefully and understand and agree that any installation, operation or maintenance of the product must be
done strictly in accordance with instructions and guidelines contained in the owner’s manual and installation guide.
Signature____________________________________________________________Date ______________________________________________
CUT ALONG
DOTTED LINE.

Overall Dimensions 35 7/8"Lx20"Wx34"H
Basin Dimensions 19 11/16"Lx12"W
Water Depth 5 11/16"
Drain Hole 1 3/4"
Faucet Type 1 3/8"(single hole)
35 7/8" [910mm]
20 1/2" [520mm]
16 1/8" [410mm]
3 1/8" [80mm]
34" [864mm]
Dia 1 1/2" [38mm] tube
level screw
to the wall
13 3/8" [340mm]
30 7/8" [785mm]
6 3/4" [170mm]
31 1/4" [794mm]
A2pcs
B 1pcs
C
D
2pcs
2pcs E 6pcs
F 6pcs G 6pcs
1pcsH

A
BC
D
HE
G
F
Top leveler
Leg leveler
drilling holes
Φ1/4"(6mm)
Section 4
NOTE: Silicone adhesive and tools necessary for installation are NOT included.
Section 3
Section 2
Section 1
1.Place the stand upright in the desired location and
level using the height adjusters built into the bottom
of the legs.
2.Use a pencil and the pre-drilled holes at the end of
the support bars to mark location of mounting
hardware on wall.
3.Drill holes for mounting hardware in the wall.
4.Insert anchors into the holes and secure the stand
to the wall with the screws.
1.Apply a thin coat of silicone adhesive to the back of
the sink where it meets the wall.
2.Apply a thin coat of silicone adhesive to the stand's
top frame where the sink will rest.
3.Carefully place the sink on the top frame of the
stand and center it.
4.Allow silicone adhesive to dry for 24 hours.
1.Connect the support bars (C) to the front legs (A).
2.Line up bolt holes where legs and support bars co-
nnect.
3.Install the bolts and tighten all bolts for all parts at
this time.
1.Connect front legs (A) and front crossbar (B).
2.Line up bolt holes where legs and crossbar connect.
3.Install the bolts but do not tighten them at this time.