Anzzi SD-AZ055-01 Series User manual

1

Left-hand door installation shown
Right-hand door installation shown
2

3
1.Wall Profile X1
2.Lower Pulley X2
3.Arch strip X2
4.Sweep Seal X1
5.Hinge-Side Vinyl Seal X1
6.Lower rail fixings X1
7.Sliding glass panel X1
8.Lower rail X1
9.Pull rod X1
10.Lower rail wall joint X2
11.Truss Head Screw St5x40 X7
12.Wall Anchor X7
13. (green) X1Wall Anchor
14.Decorative cover X7
15.Fixed X1glass panel
16.Handle X1
17.Hard rubber strip X1
18.Truss Head Screw St4x20 X1

4

5
B
A
A
10 8
14
6
1112
11
12
13
18
1.1.Simple assembly of the bottom rail, Place it at the installation location and make
sure the wall connecter (10) is 10mm away from the outside of edge,Mark on the
positions as the picture shown .(A1)
The lower fixing part (6) is 720mm away from the side wall. Mark on the
postions as the picture shown (B1)
1.2. Remove the wall connecter (10) and the lower fixing part (6) as shown in the
picture, and mark the position of the screw hole.(A2/B2)
1.3. Drill holes with φ1/4 "drilling( )
1.4. Drive the plastic anchor (12) with Truss Head Screw (11) and fix.(A4)
Drive the wall anchor green(13) into the lower fixing part with Truss Head Screw
(18) and fix. Fix the bottom rail and put on decorative cover ( 14) as
shown.(B4)
A3/B3
AB
6
11
18
13
12
A1 B1
A2 B2
A3 B3
A4 B4

6
2.1: Place the wall profile (1) on the wall as shown in the picture, make sure the distance
from the profile outside to the inside of the wall connector (10)( is 26 mm. Use a
horizontal ruler to make it vertical to the ground and mark the holes. Drill the hole with φ
1 / 4” drilling and put the plastic anchor (12) to the wall profile with the screws (11) and
26mm
11
12
1
A
A
11
12
3.1:place the hard rubber strip (17) into the unnotched side of the fixed glass panel (15),
and then clamp it against the wall profile (1) as shown in the picture
17
15
1
17
3

12mm
11
9
11
12
5
7
4
put the the notch of the glass (15) into lower fixing part (6) , lock down the cover with
screw cover (14) as shown in the picture .
5. Install the pull rod (9) on the fixed glass and leave it 12mm away from the
glass panel edge. As shown in the picture , mark position on the wall when the
pull rod (9) is horizontal. Remove the pull rod mark down scre hole position on
the wall as shown in picture 1, use a φ1 / 4” drilling to drill the hole, drive it
into the plastic anchor (12) with the screw (11) and fix.
6
14
15

M e a n w h i l e
14
6
8
2
2
2
7
2
Install the bottom lower pulley (2) into the sliding glass panel (7) as shown
7
7. Install the sliding glass panel with bottom pulley on the bottom lower rail (8), and
mount the the fixed glass panel (15) and the sliding glass (7) into the pull rod at the
same time. Tighten the screws as shown in the picture. Put on the decorative cover(14)
7
7
15 15
7
15
15
9
8
8

9
8
9
16
inside
3
4
3
5
5
3
4
3
inside
16
Install the handle (16) as shown in the picture
Install the (3)(4)(5) seal strips as shown in the picture

10
11
10
Door
DoorDoor
10. If the sliding glass cannot be vertical to bottom, you can adjust the bottom pulley as
shown in the picture, then put the decorative cover on the pulley as shown in the picture.
After the installation, adhesive sealant on the outside of the product as shown, and it
can only be used after 24 hours adhesive .