Anzzi SD-AZ052-01 Series User manual

Item: SD-AZ052-01**
SD-AZ052-02**
INSTALLATION & OPERATION MANUAL
V1.1
ANZZI GLASS SHOWER DOOR
DON’T WAIT!
REGISTER NOW!
Register your product within 90 days to ensure your product is
recognized as an official purchase and is eligible for warranty
coverage.
Mail in the completed registry card (Pg. 2) or register online
at www.swcorp.com/register
.
V1.1 – This version supersedes all previous versions as of 3/31/2022

Pleasechecktheproduct for damage and missing parts immediately upon delivery.
Damage reported later will not be covered by our warranty. Please handle the
product with care. Avoid any impact to the sides and edges of the glass.
is being
(if required by local code) plumber for all plumbing installations.
Before beginning installation, make sure all surfaces are level, solid and will
support the total weight of the unit. Also, make sure the walls are at right angles.
Irregular installation surface level, radius corners, or improper angle of side walls
will result in serious problems for your installation. Please note that some
adjustments and drilling might be necessary during the installation process.
in
When cutting or drilling metal components or handling glass, wear protective
eye wear, gloves, and closed-toe shoes to reduce the risk of personal injury.
Failure to follow instructions when installing this product may result in personal
injury, property damage, or product failure and may void the warranty.

ATTENTION
.
This model requires a minimum 1-3/8" (35mm) of flat level threshold space for installation.
.
Tools Required
Phillips
Screwdriver
Level Tape
Measure
Drill 1/8''
(3mm)
Drill Bit
1/4''
(6mm)
Drill Bit
100%
Silicone
Sealant
Pencil Rubber
Mallet
Safety
Glasses
Stud Finder
2
INSTALLATION GUIDE
BEFORE YOU BEGIN
This product is heavy
and may require two
people to install.
.
Use cut-resistant,
non-slip gloves to
reduce the risk of
personal injury and
to hold the glass firmly.
.
This product is heavy and may require two people to install.
Threshold must be level for proper installation.

PARTS
[09] x8 [10] x16 (ST4x35mm
[1-3/8"])
[12] x8 (ST4x8mm
[5/16"])
[13] x2 [14] x2
[11] x16
[15] x1
[08] x1
[01A] x1 [02] x1
[03A] x1 [03B] x1
[04] x1 [05A] x1 [05B] x1
[06] x1 [07] x1
[01B] x1
3

[13]
[
14
]
[09]
[10]
[11]
[03A]
[01B ]
[02]
[03B]
[04]
[05A]
[05B]
[08]
[
12
]
[01A]
[
06
]
[ 07 ]
ASSEMBLY
Part Description Qty.
[01A] Wall Post (L)
Wall Post (R)
Post
Top Horizontal Rail
Bottom Horizontal Rail
Magnetic Seal
Water Sealing Strips (Shorter)
Water Sealing Strips (Longer)
Fixed Panel
1
[01B] 1
[02] 1
[03A] 1
[03B]
[04]
[05A]
[05B]
[06]
1
1
1
1
1
Part Description Qty.
Door Panel
Handle Set
Anchors
Screws ST4x35
Screw Caps
Screws ST4x8
Wall Post Covers
Post Covers
1
1
8
16
[08]
[09]
[10]
[11]
[12]
[13]
[14]
16
8
2
2
[07]
4

72"[1830mm]
47"-48"[1190-1230mm]
1.57"[40mm]
5.7"[145mm]
32.8"[835mm]
SD-AZ052-01** 48*72"
23.6"[600mm]
47"-48"[1190-1230mm]
20.4"[518mm]
5

SD-AZ052-02** 60*72"
59"-60"[1495-1535mm]
1.57"[40mm]
5.7"[145mm]
32.8"[835mm]
72"[1830mm]
29.6"[752mm]
59"-60"[1495-1535mm]
26.4"[671mm]
6

ATTENTION
.
To avoid personal injury or property damage, identify components and read all instructions
before installing.
Step 1
INSTALLATION INSTRUCTIONS
.
This model requires a minimum 1-3/8" (35mm) of flat level threshold space for installation.
This shower door must be mounted to a wall stud. Minimum threshold space is required.
1.
IMPORTANT: Using a stud finder, ensure the wall intended to hold the door has a stud at the
installation point. If there is no stud in the shown area, we recommend employing a qualified
contractor to install one. (Fig 1)
This manual shows left side installation. For right side installation, follow the instructions in
page 18.
2.
Using a level, position the Wall Post L [01A] and Wall Post R [01B] on the threshold.
3.
(Fig 1)
.
The instructions below are for the Fixed Panel [06] option installed on the right..
7
Note: Level threshold is necessary for proper installation.
[01A] [01B]
Fig 1
wall
3/8"
[10mm]
wall
3/8"
[10mm]

4
5
6
[09]
Fig 2
Wear safety glasses and cut-resistant, non-slip gloves when drilling or cutting to avoid risk of
injury.
Drill a 1/4" hole at each location and insert the Anchors [09] (Fig 2.2, Fig 2.3, Fig 2.5,
Fig 2.6).
2.
Mark the drill hole locations on the wall using the predrilled holes in the Wall Post L [01A]
1.
and Wall Post R [01B] (Fig 2.1, Fig 2.4).
Step 2
8
[09]
1
2
3
[01B]
[01A]