Apantac HDBT-1-Es-POE-UHD User manual

4K/UHD HDBaseT
Extenders (4K@60, 4:4:4)
with Bi-directional POE
Supports up to 35/40m in UHD
Support up to 70m in 1080P
HDBT-SET-13
USER MANUAL v.1.0
Overview
HDBT-SET-13 uses the HDBaseT™ technology to extend HDMI 2.0 UHD signals up to
35/40 meters or HDMI 1.4 1080P signals up to 70 meters over a single CATx cable. The
HDBT-SET-13 uses the BDP™ technology that support bi-directional POE to allow the
power to be inserted on either the transmitter or receiver.
Package Contents
§ 1 x HDBT-1-Es-UHD-POE (Transmitter)
§ 1 x HDBT-1-Rs-UHD-POE (Receiver)
§ 1 x User manual
§ 1 x Power adapter DC48V with lock
§ 1 x IR Receiver
§ 1 x IR Blaster
§ 2 x mounting plates
Features
n Supports 4K@60Hz(4:4:4) up to 35/40 meters
n Supports 4K@24/25/30Hz(4:4:4) and 4K@60Hz(4:2:0) and 1080P(12bit) up to 70
meters
n Supports up to HDMI 2.0
n HDCP 1.4/2.2 compliant
n Supports 3D and CEC pass-through
n Supports RS232 bi-directional transfer
n Supports all frequency of IR control
n Supports all digital audio modes
n Supports bi-directional POE (BDP™)
Specifications
Function
HDBT-1-Es-POE-UHD
HDBT-1-Rs-POE-UHD
HDMI Connectors
1 x HDMI Type A Female
RJ45 Connectors
1 x RJ45 for HDBaseT
RS232 Connectors
1 x DB9 Female
IR Input
1 x 3.5 mm phone jack
IR Output
1 x 3.5 mm phone jack
DIP Switch
1 x 3 pin Dip Switch
LED
1 x 4x1 LED
Max Resolution
4K/UHD@60Hz (4:4:4)
Max Distance
35 meters – UHD, 40 meters – UHD w/ CAT7, 70 meters – 1080P
Power Adapter
Locking 48V DC
Weight
400g
400g
Dimension
152 x 115x 30 mm

FRONT VIEW (Transmitter/Receiver)
1. DIP SW
a) PIN 1 – OFF: Default
ON: F/W Upgrade Mode
b) PIN 2 – OFF: Long Reach Mode
ON: HDBaseT Mode
c) PIN 3 – OFF: Auto Mode
ON: Manual Mode
2. IR OUT – For IR blaster cable
3. IR In – For IR receiver cable
4. LED Status – Top to bottom: Power/HDCP/LINK/MODE
REAR VIEW (Transmitter/Receiver)
1. Power jack 48 DC (BDP™) – Can be inserted on either transmitter or receiver
2. HDBaseT Transmitter LINK Out or Receiver LINK In
3. HDMI Tranmsitter Input or Recevier Output
4. RS-232
Installation
1. Turn off source and display
2. Connect the HDMI cable between the source and the transmitter
3. Connect the HDMI cable between the display and the receiver
4. Connect the LAN (RJ45) cable between the transmitter and receiver
5. Connect the power to either the transmitter or the receiver
6. Power on the source and display
IR Blaster Cable:
Connect the IR blaster cable to <IR OUT> port
IR Receiver Cable:
Connect the IR blaster cable to <IR OUT> port
© 2020 APANTAC LLC. All rights reserved
10200 SW Allen Blvd, Suite C
Beaverton, OR 97005, USA
PHONE [phone]
FAX [phone]
The content of this document is provided in connection with Apantac LLC (“Apantac”) products. Apantac
makes no representation or warranties with respect to the accuracy or completeness of the contents of this
publication and reserves the right to make changes to specification and product descriptions at any time
without notice