Apantac HDMI-1-EM User manual

HDMI-1-EM
USER MANUAL
HDMI CATx
Extender with
Local Monitor Out
HDMI-1-EM TOP VIEW
1. EQ Adjustment
2. DC 5V 2A Power
3. EQ Indicator - ON: Auto EQ, OFF:
Manual EQ
4. Link Indicator for Local Monitor Output
5. RJ45 for CATx Output to Receiver
6. Local HDMI Monitor Output
7. HDMI Input
HDMI-1-EM REAR VIEW
1. EQ Indicator
LED ON: Auto EQ
LED OFF: Manual EQ
Troubleshooting Q & A
There is no image on my monitor
This may be an EDID issue. Follow the EDID
learning procedure described in this manual.
There is no image on my monitor.
Check the following:
Cable length
Cable quality. Low skew FTP cables per-
form better than regular network cables.
Slowly adjust the EQ knob until the image
appears.
The output of display has noise or occasion-
ally flashes.
Check the following:
Cable distance
Cable quality
Slowly adjust the EQ knob on the HDMI-1-
R until the image appears. It is best to use
a pattern generator instead of the source
to perform this adjustment.
Check for excessive RF interference in the
room.
© 2012 APANTAC LLC, All rights reserved
7556 SW BRIDGEPORT ROAD
PORTLAND, OR 97224, USA
PHONE [phone]
FAX [phone]
The content of this document is provided in connection with
Apantac LLC (“Apantac”) products. Apantac makes no
representation or warranties with respect to the accuracy or
completeness of the contents of this publication and reserves the
right to make changes to specifications and product descriptions
at any time without notice.

Installation
1. Turn off all devices.
2. Connect the monitor to the HDMI Local Moni-
tor Port.
3. Plug in the power adapter.
4. The POWER indicator and LINK indicator will
light up.
5. The ACTIVE indicator will light up when the
extender receives a valid HDMI signal.
6. LINK OUT: This port is used to cascade
more than one multi-port extender.
ED Adjustment
This is used only when the input HDMI cable is
long (more than 6 ft). In most cases the EQ Ad-
justment can be set to Auto-Mode by turning the
dial completely counter clockwise. When <EQ>
and <AUTO> LEDs will turn blue
EDID Learning
EDID mismatch is one of the most common prob-
lems in the display and extender industry. Learn-
ing the EDID on the HDMI-1-EM can easily solve
this issue.
1. Turn on the display.
2. Connect the HDMI-1-EM’s local monitor out-
put to the display with an HDMI cable (do
not connect the CATx cable). Apply power to
the HDMI-1-EM.
3. The green LED will light for one second then
turn off and the amber LED will remain flash-
ing.
4. This means the EDID from the display is now
stored in the HDMI-1-EM.
Identification Pin Assignment Color Code
Pair 1 5White-Blue
4Blue
Pair 2 1White-Orange
2Orange
Pair 3 3White-Green
6Green
Pair 4 7White-Brown
8Brown
CATx Wiring
Pin
#Signal Pin #Signal
1TMDS Data 2+ 11 TMDS Clock Shield
2TMDS Data 2 Shield 12 TMDS Clock -
3TMDS Data 2- 13 CEC
4TMDS Data 1+ 14 Reserved
(N.C. on device)
5TMDS Data 1 Shield 15 SCL
6TMDS Data 1- 16 SDA
7TMDS Data 0+ 17 DDC/CEC Ground
8TMDS Data 0 Shield 18 +5 Power
9TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
HDMI Pin Out
HDMI-1-R - long distance receiver - up to 115
ft (35 m)
HDMI-1-ERM - Extender / Receiver with local
monitor output. Can also be used to increase
the extension distance by another 55 ft (18 m)
HDMI-SR - short distance receiver - up to 35 ft
(10 m)
Receivers
Package Contents
1 x HDMI-1-EM
User Manual
Power Adapters (5V 2A)
Features
Extends 1080p signals up to 115 feet
(35 meters) with a single CATx cable
Supports HDMI 1.2 and 1.3a
Local Monitor Output
Plug and Play
Magnetic mounting plate for easy instal-
lation
FEATURES/MODEL HDMI-1-EM
Input 1 x HDMI A-Type Female
Output 1 x HDMI A-Type Female, 1 x
RJ-45
Adjustment Equalizer
Max Resolution 1080p 60Hz
Cable Distance 35m/115ft @ 1080p
Power Adapter 5V 2A DC
Dimension (mm) 62 W x 113 x D 29 H
Specifications