Apantac HDMI-1-E User manual

HDMI-1-E
HDMI-1-R
USER MANUAL
HDMI CATx
Extender / Receiver
Troubleshooting Q & A
There is no image on my monitor.
This may be an EDID issue. Follow the
EDID learning procedure described in this
manual.
There is no image on my monitor.
Check the following:
Cable length.
Cable quality. (Low skew FTP cables
perform better than regular network
cables.)
Adjust the EQ knob slowly until the im-
age appears.
The output of display has noise or oc-
casionally flashes.
Check the cable distance.
Slowly adjust the EQ knob until the im-
age appears. It is best to use a pattern
generator instead of the source to per-
form this adjustment.
Check for excessive RF interference in
the room.
© 2012 APANTAC LLC, All Rights Reserved
7556 SW BRIDGEPORT ROAD
PORTLAND, OR 97224, USA
PHONE [phone]
FAX [phone]
The content of this document is provided in connection with
Apantac LLC (“Apantac”) products. Apantac makes no
representation or warranties with respect to the accuracy or
completeness of the contents of this publication and re-
serves the right to make changes to specifications and prod-
uct descriptions at any time without notice.
HDMI-1-E FRONT VIEW
1. Link Activity Status (Green)
2. Local Power Status (Amber)
3. RJ45 for CATx Output to Receiver
4. 5V 1A Power
HDMI-1-E REAR VIEW
HDMI-1-R FRONT VIEW
1. HDMI Input from the Source
1. Cable Equalization Adjustment
2. HDMI Output to the Monitor
1. Link Activity Status (Green)
2. Local Power Status (Amber)
3. RJ45 for CATx Output to Receiver
4. 5V 1A Power
HDMI-1-R REAR VIEW

Package Contents
1 x HDMI-1-E or 1 x HDMI-1-R
(both when purchased as a set)
User Manual (s)
Power Adapters (5V 1A)
(2 when purchased as a set)
Features
Uses the latest HDBase-T technology
Extends 1080p signals up to 330 feet (100
meters with a single CATx cable)
Supports HDMI 1.4 with 3D function
Supports HDMI 1.2 and 1.3a
HDCP Compliant
Supports 3D pass-through
Supports CEC pass-through
Supports RS-232 (Bi-directional transfer)
Supports al frequency band IR control
Installation
1. Turn off all devices.
2. Connect the HDMI cable between the source and
the <HDMI IN> port of the HDMI-1-E.
3. Turn the EQ adjustment knob all the way counter-
clockwise. (This will put the EQ in the “Auto Posi-
tion”.)
4. Connect the HDMI cable between the HDMI-1-R
between the monitor and the <HDMI OUT> port
of the HDMI-1-R.
5. Connect the CATx cable between the HDMI-1-E
and HDMI-1-R’s RJ45 ports.
6. Connect the power.
What do the LED Lights Mean?
HDMI-1-E
The amber LED (Local Power Status) on the
HDMI-1-E will come on once power is applied to
the unit.
Both the green and amber LEDs will come on
when the power and the source are plugged in.
HDMI-1-R
When starting for the first time, make sure the EQ
knob is turned all the way counter clockwise.
This puts the unit to “AUTO” EQ.
The amber LED will be flashing once power is
applied to the unit.
Both the green and amber LEDs will be lit and
steady once the power, HDMI monitor cable and
the CATx are plugged in.
EQ ADJUSTMENT
When the amber LED on the HDMI-1-R is lit and
steady, this means the unit is in AUTO EQ mode.
Once the amber LED is off, the unit is in manual
EQ mode.
Make sure you adjust the EQ slowly as it is very
sensitive.
Extended Display Identification Data
(EDID) Learning
EDID mismatch is one of the most common prob-
lems in the display and extender industry. Learn-
ing the EDID on the HDMI-1-E can easily solve
this issue.
1. Turn on the display.
2. Connect the HDMI-1-R to the display with an
HDMI cable (do not connect the CATx cable).
3. Apply power to the HDMI-1-R.
4. The green LED will light for one second and
then turn off and the amber LED will remain
flashing.
5. This means the EDID from the display is now
stored in the HDMI-1-E.
Identification Pin Assignment Color Code
Pair 1 5White-Blue
4Blue
Pair 2 1White-Orange
2Orange
Pair 3 3White-Green
6Green
Pair 4 7White-Brown
8Brown
CATx Wiring
Pin
#Signal Pin #Signal
1TMDS Data 2+ 11 TMDS Clock Shield
2TMDS Data 2 Shield 12 TMDS Clock -
3TMDS Data 2- 13 CEC
4TMDS Data 1+ 14 Reserved
(N.C. on device)
5TMDS Data 1 Shield 15 SCL
6TMDS Data 1- 16 SDA
7TMDS Data 0+ 17 DDC/CEC Ground
8TMDS Data 0 Shield 18 +5 Power
9TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
HDMI Pin Out
FEATURES/
MODEL
HDBT-1-E HDBT-1-R
HDMI In 1 x HDMI A-Type
Female
None
HDMI Out 1 x HDMI A-Type
Female
RJ-45 1 1
IR OUT 3.5 mm phone jack None
IR IN None 3.5 mm phone jack
Max Resolution 1080p 60Hz 1080p 60Hz
Cable Distance 100 meters (Max) 100 meters (Max)
Power Adapter 12 V DC 12 V DC
Weight g) 310g 310g
Dimension
(mm)
150 W x 80 x D 25
H
150 W x 80 x D 25
H
Specifications