Aqua Lung RESCUE SWIMMER VEST User manual

RESCUE SWIMMER VEST
Part no. 769045
Before using the Rescue Swimmer Vest you must read the•
instruction sheet completely.
Before using, inspect the entire vest for leakage or other• damage.
If any part of the vest does not function properly, or it is dam• aged,
remove the Rescue Swimmer Vest from service until repaired.
DonotinhalefromtheRescueSwimmerVestoralinator.The•
vest may contain contaminants from a previous CO2 ringor
other source.
TheRescueSwimmerVestisnotapprovedforuseinSCUBA• Diving.
Place the Rescue Swimmer Vest over your head. Route the waist1.
strap underneath your arms and then tighten strap. (See Fig. 1).
Fully inate the Rescue Swimmer Vest by depressing the oral inator2.
button (See Fig. 2) and exhale into the mouthpiece until the vest is full.
If the t is too tight, adjust the strap for comfort.
Figure 1 Figure 2
WARRANTY
Aqua Lung America Inc. warrants this product to be free from defects in
material and workmanship for a period of one year from the date of original
purchase. Aqua Lung will repair or replace products that prove to be defec-
tive under normal conditions and proper use.
Literature PN 18296
2340 Cousteau Court, Vista, CA 92081
Phone [phone] Fax [phone]
www.aqualung.com/militaryandprofessional
Rev 12/11

PRE-OPCHECKOUT
Prior to each use, the vest should be given a thorough visual
inspection and function test.
Fully inate the vest and set aside for 30 minutes; loss of rmness 1.
indicates leakage, which must be corrected before use.
Ensure that all stitched together components are not separating.2.
Check that the oral inator properly functions by depressing 3. the oral
inator button and exhale into the mouthpiece.
Remove the CO4. 2 cartridges and inspect both actuators. Ensure both
actuators operate correctly by pulling the knob to operate the actuat-
ing lever and checking that the piercing pin travels up and down. Re-
turn the actuating lever to the ring position prior to re-threading the
CO2 cartridge into the actuator.
Perform a function check on the over pressure relief valve (OPRV) 5.
by fully inating the vest and then squeezing the vest to ensure the
OPRV opens allowing air to escape. Next, push the deator button to
ensure the dump valve is correctly working by allowing air to escape
(See Fig. 3).
NOTE: Over pressure relief valve (OPRV) will actuate when the
pressure inside the vest exceeds 2.5 - 3.5 PSI (0.17 - 0.24 BAR)
greater than external pressure.
Figure 3
POST-OPMAINTENANCE
Proper maintenance will provide for years of reliable service. The
Rescue Swimmer Vest should be stored away from direct sunlight.
After each use, soak the exterior of the 1.
vest with fresh water.
Detach HABD / SEA pocket (optional)2.
and fresh water rinse all components
(See Fig. 4).
Open storage pocket and fresh water 3.
rinse. Ensure the hook and loop fabric
is clean from all debris (See Fig. 5).
Unscrew both CO4. 2 cartridges from
the actuators and fresh water rinse all
components.
Inate the vest with air, turn it to an 5.
inverted position and drain any water
out by depressing oral inator button.
If water drains from inside the vest, a
fresh water rinse should be done.
Figure 4
Figure 5
a. To fresh water rinse the vest, depress the oral ination valve button
and directly ll the vest with water.
b. Swish the water around to remove any mineral deposits, invert the
vest so the oral ination valve is the lowest point and drain the
water by depressing the oral ination valve button. Taste the last
remaining drops of water for salt. If salt is detected, repeat the
cleaning procedure for the internal bladder.
To dry the vest after cleaning, inate the 6. vest until it is half full, this will
allow the inner bladder to dry. DO NOT dry the vest in direct sunlight.
Store the half full, inated vest in a cool, dry and clean area.
Check the vest 30 minutes later for any leakage. If any leakage or 7.
holes are detected, repair the vest utilizing the Aqua Lung Repair Kit
pn 42611.
WARNING: DONOTuseaerosolsiliconespraysorclean-
ers to lubricate the components, the propellants or carrier
solvent cause cracking or crazing.
NOTE: Ensure the actuator is free of debris and the CO2 car-
tridge washer is in place prior to re-installing the CO2 cartridge. NOTE: Remove CO2 cartridge
washer from actuator prior to fresh
water rinse.