Aranet PRO User manual

USER GUIDE
Aranet PRO/Aranet PRO+
Applicable for Aranet PRO/Aranet PRO+ with firmware starting from v.3.0.1
Document revision v.9
July 2022

Page 2
FCC Compliance statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the device.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from the one the receiver is connected to.
● Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Aranet PRO/PRO+ does not contain serviceable parts. Warranty will not be applicable in the
event of Aranet PRO has been opened or Aranet PRO+ warranty seals are damaged.
The information presented in this guide is the property of SAF Tehnika, JSC. No part of this document may
be reproduced or transmitted without proper permission from SAF Tehnika, JSC.
The specifications or information contained in this document are subject to change without notice due to
continuing introduction of design improvements. If there is any conflict between this document and
compliance statements, the latter will supersede this document.
SAF Tehnika, JSC has no liability for typing errors in this document or damages of any kind that result from
the use of this document.
To get up to date information about accessories and their availability, please contact sales representative.
© 2017 - 2022 SAF Tehnika JSC. All rights reserved.

Page 3
Industry Canada Regulatory Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following
two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.

Page 4
TABLE OF CONTENTS
1 INTRODUCTION 6
1.1 ARANET PRO BASE OVERVIEW 7
1.1.1 What’s in the box 7
1.1.2 Aranet PRO indicators 8
1.1.3 Aranet PRO mounting 9
1.1.4 Aranet PRO ports 9
1.1.5 Aranet PRO power options 10
1.1.6 Internal battery backup 10
1.2 ARANET PRO+ BASE OVERVIEW 11
1.2.1 What’s in the box 11
1.2.2 Aranet PRO+ front view 12
1.2.3 Aranet PRO+ indicators 13
1.2.4 Aranet PRO+ mounting 13
1.2.5 SIM-card installation 14
1.2.6 Aranet PRO+ power options 14
1.2.7 Emergency switching off 14
1.3 ARANET PRO/PRO+ SPECIFICATIONS 15
2 INITIAL SETUP 17
2.1 Initial setup of Aranet PRO/Aranet PRO+ 17
2.1.1 Initial setup of Aranet PRO/Aranet PRO+ using built-in Wi-Fi Access Point 17
2.1.2 Initial setup of Aranet PRO/Aranet PRO+ using Ethernet cable 18
2.1.3 Initial Login and Fast Settings 19
2.2 Pair sensors to Aranet PRO /PRO+ 23
2.3 Connecting Aranet PRO/PRO+ to internet network 26
2.3.1 Connecting Aranet PRO/PRO+ to internet network using local Wi-Fi router 26
2.3.2 Connecting Aranet PRO/PRO+ to internet network using external router 28
2.4 Accessing the Aranet PRO/PRO+ from Internet 30
3 ARANET SENSORHUB OVERVIEW 31
3.1 Main navigation bar 31
3.2 Main menu 31
3.3 Graphs 33
3.4 Sensors 36
3.5 Groups 36
3.5.1 Using groups 36
3.6 System 38
3.6.1 Status menu 38
3.6.2 Region menu 39
3.6.3 Time menu 40
3.6.4 Network menu 41
3.6.5 Firmware menu 45
3.6.6 Backup menu 47
3.6.7 Tools menu 47
3.6.8 Licenses menu 48
3.6.9 Notifications 48
3.6.10 Radio menu 54
3.6.11 Aranet MINI monitor mode 55
3.6.12 Users menu 57

Page 5
3.6.13 SNMP menu 58
3.7 Integrations 59
3.7.1 MQTT 59
3.7.2 Aranet Cloud 62
3.7.3 Modbus 65
4 SENSORS’ SPECIFIC NOTES 68
4.1.1 Weight Sensor 68
4.1.2 Soil (Substrate) Sensor 69
4.1.3 4-20 mA and Voltage Sensors 71
4.1.4 Stem Micro-Variation sensor 72
4.1.5 Ultrasonic Distance sensor 75
4.1.6 CO2 and Temperature sensor 76
4.1.7 Pulse Counter sensor 76
4.1.8 NH3 Sensor kit 77
5 LEGAL INFORMATION 78
5.1 TERMS OF USE 78
5.2 WARRANTY 78
5.3 RMA (RETURN MERCHANDISE AUTHORIZATION) FORM 80
5.4 INTELLECTUAL PROPERTY RIGHTS 81
5.5 DATA SECURITY 81
5.6 CLEANING AND MAINTENANCE 81
5.7 ACCESSORIES 82
5.8 DISCLAIMER 82
5.9 ADDITIONAL INFORMATION 82

Page 6
1 INTRODUCTION
Aranet offers environmental monitoring solutions for a variety of businesses. Aranet PRO and Aranet PRO+
are industrial grade environment monitoring solutions.
Aranet PRO/PRO+ can support 12, 50 or 100 sensors depending on license purchased.
The base station has exceptional sensitivity and allows placing the sensors within line-of-sight range of at
least 3km/1.9mi.
All Aranet PRO/Aranet PRO+ base stations include embedded local webserver Aranet SensorHUB. Easy
to use interface allows viewing, analyzing, and comparing data in real time, setting thresholds for alarms as
well as exporting reports. Responsive design of the software adapts to smartphone, tablet, or laptop.
Document describes the functionality of Aranet PRO/Aranet PRO+ with firmware version starting
v3.0.1.
Aranet PRO and Aranet PRO+ differences in hardware and software are highlighted in
corresponding chapters using the icon.
Aranet PRO having part numbers TDSBWPA1.xxx, TDSBWPA2.xxx, TDSBWPC2.xxx are
referred in this document as Aranet PRO Mk2and their specific differences in software are
highlighted in corresponding chapters using the icon.
Visit www.aranet.com for more information.

Page 7
1.1 ARANET PRO BASE OVERVIEW
1.1.1 What’s in the box
(1) 1 pc of Aranet PRO base station with installed Aranet SensorHUB software and License
(2) 1 pc of Aranet PRO base station mount
(3) 2 pcs of W1412 screws
(4) 1 pc of AC power adapter (EU or US version depending on product version)

Page 8
1.1.2 Aranet PRO indicators
(1) Sensor data indicator LED – flashes amber every time a data packet is received from a sensor.
(2) Wi-Fi connection indicator LED – amber light when Aranet PRO is connected to Wi-Fi or works in
Access Point mode
(3) LAN connection indicator LED – amber light when Aranet PRO is connected to LAN connection through
an Ethernet cable
(4) 12V power indicator LED – green light when Aranet PRO is connected to 12V power either through a
PoE connection or with the included AC power adapter
(5) Battery power indicator LED – red light when Aranet PRO is using built in backup battery power

Page 9
1.1.3 Aranet PRO mounting
(1) (2) (3)
(1) Base station mount configuration for positioning on vertical surface (e.g., wall).
(2) Base station mount configuration for positioning on vertical surface (e.g., wall).
(3) Base station mount configuration for placement on horizontal surface (e.g., table).
1.1.4 Aranet PRO ports
(1) On-Off switch – switch in the left position means Aranet PRO is turned off, switch in the right position
means Aranet PRO is turned ON
(2) AC Power port - for using the included AC power adapter to power Aranet PRO
(3) Ethernet port – for LAN connectivity as well as PoE connectivity
(4) Reset button, press, and hold for 5 seconds or more and then release the button to reset network
settings and password of “root” user account. The reset button is accessed through hole with some thin
object like pencil.
(5) USB port – for connecting USB modem to enable SMS notification functionality, and for connecting and
configuring Aranet MINI.

Page 10
1.1.5 Aranet PRO power options
Aranet PRO can be powered with the included power adapter either directly or via the passive Ethernet
injector.
1.1.6 Internal battery backup
Aranet PRO is supplied with built in battery backup providing up to 30 minutes of power supply in case of
main power failure. It is meant only as a backup and allows Aranet PRO to shut down safely. System
warning (if enabled) will be issued in case of main power failure and before Aranet PRO switches off
completely. Warning will be sent as email and/or SMS to the destination configured by users belonging to
the Administrator group.
!WARNING! ARANET PRO BASE STATIONS CONTAIN A LI-ION 14500 PROTECTED
TYPE RECHARGEABLE BATTERY AND A CR2032 TYPE BATTERY. RISK OF DAMAGE
IF BATTERY IS REPLACED BY AN INCORRECT TYPE. THE USER IS RESPONSIBLE
FOR DISPOSAL OF BATTERIES ACCORDING TO THE STATE LEGISLATION.

Page 11
1.2 ARANET PRO+ BASE OVERVIEW
1.2.1 What’s in the box
(1)
(2)
(1) 1 pc of Aranet PRO+ base station with installed Aranet SensorHUB software and License
(2) 1 pc of Cat.5 Ethernet cable 1m

Page 12
1.2.2 Aranet PRO+ front view
(1) IP68 protected RJ-45 Ethernet port for Network and Power connection.
(2) Screws for detaching/securing Aranet PRO+ case lid – 4 pcs.
(3) Warranty seals - Nylon screws – 4 pcs. Warranty is lost if damaged.
(4) SIM-card holder (P/N TDSBOB03, TDSBOBU3, TDSBOBC3 only).
(5) Network Reset button; press and hold for 5 seconds or more and then release the button to reset
network settings and password of “root” user account.
(6) Humidity membrane. Do not unscrew!

Page 13
1.2.3 Aranet PRO+ indicators
(1) Sensorsdata indicator LED – flashes amber every time a data packet is received from a sensor.
(2) Cellular connection indicator – slow flashes red when no SIM-card is installed, or no connection is
established; fast flashes with steady pauses when connected to GSM LTE network.
(3) Wi-Fi connection indicator LED – yellow light when Aranet PRO+ Wi-Fi network interface is
enabled, and base is connected to Wi-Fi or works in Access Point mode.
(4) Ethernet connection indicator LED – yellow light when Aranet PRO+ is connected to LAN using
cable
(5) System indicator – green light when Aranet PRO+ system is started.
(6) Power indicator LED – green light when Aranet PRO+ is powered.
1.2.4 Aranet PRO+ mounting
Aranet PRO+ case has four dedicated holes for 4…4.5 mm screws by which base can be mounted to
smooth surface:

Page 14
1.2.5 SIM-card installation
Aranet PRO+ P/N TDSBOB03, TDSBOBU3, TDSBOBC3 is equipped with GSM LTE 4G modem
accepting Mini size SIM-card.
To install SIM-card into modem:
(1) Disconnect Aranet PRO+ from power source and wait for system to shutdown (all LEDs go Off).
(2) Detach Aranet PRO+ transparent lid by loosing 4 screws at the base’s case corners.
(3) Locate SIM-card holder.
(4) Loosen the holder cover by rotating metal locking plate counterclockwise.
(5) Flip the cover off.
(6) Insert SIM-card into the cover observing correct orientation.
(7) Flip cover back and fasten it by rotating metal locking plate clockwise.
(8) Put back Aranet PRO+ lid and fasten 4 screws.
1.2.6 Aranet PRO+ power options
Aranet PRO+ is powered by 802.3af PoE directly from the PoE enabled Ethernet switch or using optional
PoE insert.
1.2.7 Emergency switching off
Aranet PRO+ can shut down and switch off safely in case of main power failure. System notification will be
sent as email and/or SMS to the destination configured by users belonging to the Administrator group.
!WARNING! ARANET PRO+ BASE STATIONS CONTAIN CR2032 TYPE BATTERY. RISK
OF DAMAGE IF BATTERY IS REPLACED BY AN INCORRECT TYPE. THE USER IS
RESPONSIBLE FOR DISPOSAL OF BATTERIES ACCORDING TO THE STATE
LEGISLATION.

Page 15
1.3 ARANET PRO/PRO+ SPECIFICATIONS
Aranet PRO
Aranet PRO+
Part Number (P/N)
TDSBWB01,
TDSBWBU1,
TDSBWBC1,
TDSBWPA1.xxx,
TDSBWPA2.xxx,
TDSBWPC2.xxx
TDSBOB03,
TDSBOBU3,
TDSBOBC3
TDSBOA03,
TDSBOAU3,
TDSBOAC3
Maximum sensor
count*
100/50/12
Alarm type
Email
Optional alarm
SMS notification
through external
USB modem
SMS notification
N/A
Memory
10 years of measurements of 100 sensors**
Receiver sensitivity
-127 dBm
Channels – Europe
EU868
Channel 1: 868.10 MHz
Channel 2: 868.30 MHz
Channel 3: 868.50 MHz
Channels –
Americas US920
Channel 1: 917.3 / 922.9 MHz
Channel 2: 917.5 / 923.1 MHz
Channel 3: 917.7 / 923.3 MHz
Channel 4: 917.9 / 923.5 MHz
Channels – Russia
RU869
Channel 1:
868.85 MHz
N/A
Channel 2:
869.05 MHz
N/A
Channels – Asia
AS923
Channel 1: 923.1 MHz
Channel 2: 923.3 MHz
User interface
Aranet SensorHUB
Interface
accessibility
PC, tablet, or smart phone connected via Ethernet cable
or local Wi-Fi connection
Interface languages
English, French, Spanish, Nederland, Russian, Latvian, German, Portugal
Temperature scale
Celsius, Fahrenheit, Kelvin
Data protection
Password protected user accounts, encryption for data
Communication
Ethernet cable, local
Wi-Fi (2.4 GHz)
Ethernet cable,
local Wi-Fi
(2.4 GHz),
GSM LTE 4G
Ethernet cable,
local Wi-Fi
(2.4 GHz)

Page 16
Browser
compatibility
Latest versions of
Chrome
Safari
Edge
Power options
AC/DC power
adapter
PoE 802.3af
Optional power
supply with Passive
12V PoE injector
N/A
Built-in battery
(backup power up to
30 min)
Supercapacitors for safe shutdown
Operating
temperature
0°C to 40°C /
32°F to 104°F
-40 °C to +60 °C / -40 °F to 140 °F
Operating humidity
0% to 100%
non-condensing
Dimensions
107x170x26 mm /
4.2×6.7×1.02 in
w/o mounting
bracket
180 x 120 x 45 mm /
7.09 x 4.72 x 1.77 in
Ports
12VDC power port,
1 x Ethernet,
1 x USB A
1 x Ethernet
SIM-card
N/A
1 x Mini size
N/A
Weight
190g/ 6.7oz
w/o mounting
bracket
250 g /(8.8 oz
Construction
ABS Plastic, steel
mounting bracket
PC plastic
Protection class
IP42
IP67
CE / FCC / IC
Marking
Yes
CE
Included
AC/DC power
adapter, mounting
bracket
Cat.5 Ethernet cable 1 m
Additional – Europe
Aranet MINI can be used as a monitor
* Depending on license purchased
** Aranet4 PRO sensor with 5-minute TX interval chosen for calculation.

Page 17
2 INITIAL SETUP
2.1 Initial setup of Aranet PRO/PRO+
Aranet PRO/Aranet PRO+ can be configured with built-in Wi-Fi Access Point or with Ethernet connection to
local network. This allows quick and easy access to Aranet PRO using any personal devices like PC, tablet,
or smartphone.
Aranet PRO/Aranet PRO+ base station Network factory settings are:
• Wi-Fi interface configured as Access Point:
o SSID - “Aranet-******” (refer to the label
attached to Aranet PRO/PRO+);
Encryption – WPA2-PSK-CCMP;
o Aranet PRO Mk2 SSID - “Aranet-******”
Encryption – None;
o IP address – 192.168.206.100;
o Subnet Mask – 255.255.255.0
• Ethernet Interface:
o DHCP client – On;
o Static IP fallback – On;
o IP address – 192.168.205.100;
o Subnet Mask – 255.255.255.0
2.1.1 Initial setup of Aranet PRO/PRO+ using built-in Wi-Fi Access Point
Aranet PRO/Aranet PRO+ setup using built-in Wi-Fi Access Point is the easiest way to start working.
(1) Aranet PRO+: Plug in Ethernet cable connected to powered PoE insert “OUT” terminal or
PoE enabled switch.
Wait until LED indicators “Power”, “System”, and “Wi-Fi” turn On.
Aranet PRO: Plug in included AC power adapter jack and switch base on using On-Off switch.
Wait until LED indicators next to “12V” and “Wi-Fi” turn on and wait for another 30 seconds.
(2) Using a smartphone or a PC open its Wi-Fi
network settings and find new wireless network
access point called “Aranet-******”.
Connect to it using password from the label.
Aranet PRO Mk2 – connect without
password.
(3) Open internet browser and type in the URL bar IP address: 192.168.206.100
(4) You should now see the Aranet PRO/Aranet PRO+ login screen (refer to chapter 2.1.3 Initial Login
and Fast Settings of this manual).

Page 18
2.1.2 Initial setup of Aranet PRO/PRO+ using Ethernet cable
I. Aranet Pro connection to Local Network (LAN) with working DHCP server
II. Aranet PRO/Aranet PRO+ connection to PC
(1) Aranet PRO+: Plug in Ethernet cable connected to powered PoE enabled switch or
powered PoE insert “OUT” terminal; plug in another Ethernet cable to PoE insert “IN”
terminal and connect it to LAN Ethernet switch (router).
Wait until LED indicators “Power”, “System”, and “Ethernet” turn On.
Aranet PRO: Plug in Aranet PRO into power source using the AC power adapter and plug in
the Ethernet cable that connects Aranet PRO into local network (Router or Ethernet Switch)
Wait until LED indicators next to “12V” and “Wi-Fi” turn on and wait for another 30 seconds.
(2) Search for new IP-address assigned to Aranet PRO/Aranet PRO+ by DHCP server. You can
consult your local network administrator or scan your local network with any Network
scanner.
(3) Open internet browser and type in the URL bar discovered in the previous step IP address.
(4) You should now see the Aranet PRO/Aranet PRO+ login screen (refer to chapter 2.1.3 Initial
Login and Fast Settings of this manual).
(1) Aranet PRO+: Plug in Ethernet cable connected to powered PoE insert “OUT” terminal;
plug another Ethernet cable to PoE insert “IN” terminal and connect it directly to your PC.
Wait until LED indicators “Power”, “System”, and “Ethernet” turn On.
Aranet PRO: Plug in included AC power adapter jack and switch base on using On-Off
switch, plug in Ethernet cable that connects Aranet PRO directly to your PC. Switch Aranet
PRO on. Wait until LED indicators next to “12V” and “LAN” turn on and wait for another 30
seconds.
(2) Make sure the PC is not connected to any Wi-Fi Internet connections.
(3) For Windows 10, in the Control Panel menu navigate to Control Panel >Network and
Internet >Network and Sharing Center.
(4) Click “Change adapter settings”.
(5) Right-click on “Local Area Connection” and click on “Properties”.
(6) Select “Internet Protocol Version 4 (TCP/IPv4)” and click on “Properties”.
(7) Select “Use the following IP Address”, set IP address to 192.168.205.101 and subnet mask
to 255.255.255.0, leave rest of the fields blank and press “Save”.
(8) Open the Internet browser and in URL bar type the IP address of Aranet PRO/PRO+:
192.168.205.100
(9) You should now see the Aranet PRO/PRO+ login screen (refer to chapter 2.1.3 Initial Login
and Fast Settings of this manual).

Page 19
2.1.3 Initial Login and Fast Settings
Username and password for login can be found on the label attached to Aranet PRO/PRO+ (see example
below).
Aranet PRO Mk2:
Username: root
Password: changeme
!NOTE! Root is an administrator account. For security reasons, we recommend changing
the password as soon as possible.
We also recommend creating separate accounts for users as required. There are two levels
(groups) of access - user and administrator. User group accounts have read-only
permissions, can only view parameters, and can subscribe to notifications. The total account
limit is 20 (including root account).
After entering Username, Password and clicking LOGIN button for the first time, following page will open:
Now you can change the regional, network, and other settings, as well as start pairing the sensors.
Refer to chapter 3.2 ARANET SENSORHUB OVERVIEW for detailed information about Menu.

Page 20
It is a good practice to start with System settings.
Click with your mouse to the Menu icon to open MAIN menu and select System:
Navigate to Region menu and set your preferred Language, Units, Time, and Data formats. Click Save