Arbor Technology LYNC-817 Series User manual

I
LYNC-817 Series
Fanless 17” Industrial Panel PC with
Intel®Celeron®J1900 2.0GHz
User’s Manual
Version 1.2
2017.12
P/N: 4012081700120P

- II -
Revision History
Version Time Description
1.0 2014/11 Initial release
1.1 2015/01 P.3: Revise BIOS, Expansion Bus
AMI--> Insyde
Mini-card socket (USB Interface)
P.6, 31, 50, 51, 52: Remove WiFi-AT2350
Module description
P.6: Add CTOS MM-3C-4G
1.2 2017/12 “1.5.2. Congure-to-Order Service”
updated with ELPP-0101-C224, ANT-D11
and WiFi-AT2350
“A.1. Install Wi-Fi Module”
Revise intallation method by using riser
card

- i -
Contents
Revision History ................................................................................II
Contents..............................................................................................i
Preface...............................................................................................iii
Copyright Notice .....................................................................................iii
Declaration of Conformity .......................................................................iii
CE....................................................................................................iii
FCC Class A ....................................................................................iii
RoHS .............................................................................................. iv
SVHC / REACH .............................................................................. iv
Important Safety Instructions .................................................................. v
Warning.................................................................................................. vi
Lithium Battery Replacement................................................................. vi
Technical Support .................................................................................. vi
Warranty.................................................................................................vii
Chapter 1 - Introduction....................................................................1
1.1. The Computer ..................................................................................2
1.2. About this Manual ...........................................................................2
1.3. Specications...................................................................................3
1.4. Inside the Package .......................................................................... 5
1.5. Ordering Information ........................................................................5
1.5.1. Optional Accessories ............................................................. 6
1.5.2. Congure-to-Order Service.................................................... 6
Chapter 2 - Getting Started...............................................................7
2.1. Dimensions ......................................................................................8
2.2. Tour the Computer ........................................................................... 9
2.2.1. Front View..............................................................................9
2.2.2. Rear View ............................................................................10
2.2.3. Bottom View......................................................................... 11
2.2.4. Side View.............................................................................12
2.2.5. Top View ..............................................................................12
2.3. Driver Installation Note................................................................... 13
Chapter 3 - Engine of the Computer..............................................14
3.1. Board Layout..................................................................................15
3.2. Jumpers and Connectors...............................................................16
3.2.1. Jumpers ..............................................................................16
3.2.2. Connectors ..........................................................................19
Contents

- ii -
Contents
Chapter 4 - Installation and Maintenance......................................27
4.1. Use Onboard Jumpers and Connectors ........................................ 28
4.2. Install Hardware .............................................................................29
4.2.1. Install SSD or HDD ..............................................................29
4.2.2. Install CFast Card ................................................................30
4.2.3. Install Wi-Fi Module .............................................................31
4.2.4 Install PCI or PCIe Card ....................................................... 31
4.2.5 Install 2nd CFast module ......................................................33
4.3. Mount the Computer ......................................................................34
4.3.1. Panel Mounting....................................................................34
4.3.2. VESA Mounting.................................................................... 35
4.4. Wire DC-Input Power Source......................................................... 36
Chapter 5 - BIOS..............................................................................37
5.1. Main ...............................................................................................40
5.2. Advanced ....................................................................................... 41
5.2.1. Boot Conguration ...............................................................42
5.2.2. PCI Express Conguration .................................................. 42
5.2.3. Miscellaneous Conguration................................................ 43
5.2.4. SATA Conguration..............................................................43
5.2.5. SIO Fintek 81216.................................................................43
5.3. Security ..........................................................................................44
5.4. Power ............................................................................................45
5.5. Boot................................................................................................46
5.6. Exit .................................................................................................47
Appendices ......................................................................................49
Appendix A: Wi-Fi Module Hardware/Software Installation................... 50
A.1. Install Wi-Fi Module................................................................50
Appendix B: PenMount Utilities............................................................. 55
B.1. PenMount Control Panel ........................................................55
B.2. PenMount Gesture .................................................................60

- iii -
Preface
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this document may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the
directives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of shielded
cables. This kind of cable is available from ARBOR. Please contact your local
supplier for ordering information.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.

- iv -
Preface
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are
in compliance and conform to the European Union’s Restriction of Use of
Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main purpose
of the directive is to prohibit the use of lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl
ethers (PBDE) in electrical and electronic products. Member states of the EU are
to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not contain
unintentional additions of lead, mercury, hex chrome, PBB or PBDB that exceed
a maximum concentration value of 0.1% by weight or for cadmium exceed
0.01% by weight, per homogenous material. Homogenous material is dened as
a substance or mixture of substances with uniform composition (such as solders,
resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-96.5%),
Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the earth
we live, Arbor hereby conrms all products comply with the restriction of SVHC
(Substances of Very High Concern) in (EC) 1907/2006 (REACH --Registration,
Evaluation, Authorization, and Restriction of Chemicals) regulated by the
European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- v -
Preface
Important Safety Instructions
Read these safety instructions carefully
1. Read all cautions and warnings on the equipment.
2. Place this equipment on a reliable surface when installing. Dropping it or
letting it fall may cause damage
3. Make sure the correct voltage is connected to the equipment.
4. For pluggable equipment, the socket outlet should be near the equipment
and should be easily accessible.
5. Keep this equipment away from humidity.
6. The openings on the enclosure are for air convection and protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
7. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
8. Never pour any liquid into opening. This may cause re or electrical shock.
9. Never open the equipment. For safety reasons, the equipment should be
opened only by qualied service personnel.
10. If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user’s manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
11. Keep this User’s Manual for later reference.

- vi -
Preface
Warning
The Box PC and its components contain very delicately Integrated Circuits (IC).
To protect the Box PC and its components against damage caused by static
electricity, you should always follow the precautions below when handling it:
1. Disconnect your Box PC from the power source when you want to work on
the inside.
2. Use a grounded wrist strap when handling computer components.
3. Place components on a grounded antistatic pad or on the bag that came
with the Box PC, whenever components are separated from the system.
Lithium Battery Replacement
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trash can. It must be disposed of in
accordance with local regulations concerning special waste.
Technical Support
If you have any technical difculties, please consult the user’s manual rst at:
ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still cannot
nd out the answer.
http://www.arbor-technology.com
E-mail:[e-mail]

- vii -
Preface
Warranty
This product is warranted to be in good working order for a period of one year
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by any
other related party.
Vendors disclaim all other warranties, either expressed or implied, including but
not limited to implied warranties of merchantability and tness for a particular
purpose, with respect to the hardware, the accompanying product’s manual(s)
and written materials, and any accompanying hardware. This limited warranty
gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or faxing
the vendor and requesting a Return Merchandise Authorization (RMA) number.
Returned goods should always be accompanied by a clear problem description.

- viii -
This page is intentionally left blank.

- 1 -
1Chapter 1
Introduction
Chapter 1 - Introduction

- 2 -
Introduction
1.1. The Computer
Product Highlights
• Cable-less , Fanless Design
• User Selectable Modularized Design
• 17” 1280 x 1024 SXGA LCD Display w/
LED Backlight
• Front Panel IP65 Compliant
• Serial Ports (RS-485), w/ Auto-ow
Control
• Mini-card Sockets x 1, PCI x 1 or PCIe x 1
• Semi-Piercing DB9 Hole Reserved for
Field-bus Card
• SMA Antenna Holes for Optional WiFi Function
• 9~36V Wide Range DC Input
1.2. About this Manual
This manual is meant for the experienced users and integrators with hardware
knowledge of personal computers. If you are not sure about the description in
this manual, consult your vendor before further handling.
We recommend that you keep one copy of this manual for the quick reference
for any necessary maintenance in the future. Thank you for choosing ARBOR
products.

- 3 -
Introduction
1.3. Specications
System
CPU Intel J1900 Quad-Core™ Processor 2.0GHz
Memory
1 x DDR3L SO-DIMM Socket, supporting 1066/1333
MHz SDRAM up to 8GB
1 x 4GB DDR3L SO-DIMM memory module installed
LAN 2 x Intel® I210AT GbE controllers
Watchdog Timer 1~255 levels reset
Storage
1st Device 1 x outside-accessible CFast slot
2nd Device 1 x outside accessible 2.5” Drive Bay (Default), or CFast
slots (Optional)
LCD Display
Size/Type 17" TFT LCD Panel
Max. Resolution 1280 x 1024, SXGA
Max. Colors 16.2M
Luminance 350 cd/m²
Touch Screen 5-wire Analog Resistive
Button & Indicator
Function Key Power on/off
LED Indicator Power on LED
Power System
Power Input DC 9~36V
Power
Consumption Max. 28.0W (w/o I/O cards)
Qualification
Certification CE, FCC Class A
Expansion

- 4 -
Introduction
Expansion Bus
1 x Mini-card socket ( full-size) (USB only)
1 x PCI 32-bit slot (default) or 1 x PCIe x1 slot (both
Riser Cards are included in Standard Accessories)
Optional 1 x semi-piercing DB9 hole reserved
External I/O
Serial Ports 2 x RS-232 and 2 x RS232/485 ports with
auto-flow design, all are DB9 connectors
USB Ports 1 x USB 3.0 Type-A USB port
3 x USB 2.0 Type-A ports
LAN 2 x RJ-45 GbE ports
DVI 1 x DVI-I connector
WiFi 2 x SMA antenna holes are for optional WiFi function
Audio Line-out
Mechanical
Mounting Type Panel Mounting and VESA-75/100 Mounting
Chassis Panel-mounting chassis, aluminum front bezel and
SECC steel chassis
Dimension
(W x H x D)
428.00 x 380.00 x 77.00 mm
(16.8” x 14.9” x 3.0”)
Weight (Net) 6.5 kg (14.3 lb)
Environmental
Operating Temp. -0ºC ~ 55ºC (-32 ~ 131°F)
Storage Temp. -10ºC ~ 75°C (-50 ~ 167°F)
Operating
Humidity 10 ~ 95% RH @ 55°C (non-condensing)
Vibration 5 ~ 500Hz, 2Grms Random (with CF/SSD)
Shock Operating 10G, 11ms
Non-operating 30G, 11ms (with CF/SSD)
OS Support
W7 Pro / WS7E / W8.1 Industry

- 5 -
Introduction
1.4. Inside the Package
Upon opening the package, carefully inspect the contents. If any of the items
is missing or appears damaged, contact your local dealer or distributor. The
package should contain the following items:
1 x LYNC-817 industrial panel PC
1 x Accessory Box that contains the
following items:
• Driver CD
• User’s manual
• Screws/cable
• 3-pin plug for terminal block
1.5. Ordering Information
LYNC-817 17” Intel®Celeron®Processor J1900 industrial panel PC

- 6 -
Introduction
1.5.1. Optional Accessories
The following items are normally optional, but some vendors may include them in
the standard package, or some vendors may not carry all the items.
PAC-P060W-02 12V/5A 60W AC/DC power adapter kit
1.5.2. Congure-to-Order Service
Make the computer more tailored to your needs by selecting one or more
components from the list below to be fabricated to the computer.
150G SSD Intel® 2.5" 150GB SATAIII SSD Kit
MM-3C-4G 4GB DDR3-1333 SDRAM
ELPP-0101-C224
PCIe x 1 to mPCIe adapter card
(inserted to PCIe x 1 Riser card for
optional WiFi module installation)
ANT-D11 2.4G/5G Dual-band WiFi Antenna
WiFi-AT2350 Atheros AR9462 WiFi Module w/ 20cm
& 30cm internal wiring

- 7 -
2Chapter 2
Getting Started
Chapter 2 - Getting Started

- 8 -
Getting Started
2.1. Dimensions
The following illustration shows the dimensions of the computer, with the
measurements in width, depth, and height called out.
428.00
380.00
5.00
21.20
(50.80)
406.40 (cut out)
359.40 (cut out)
77.00
357.40
234.40
374.65
404.40
Unit:mm

- 9 -
Getting Started
2.2. Tour the Computer
Take a look around the computer and nd the external controls and connectors.
2.2.1. Front View
On the front side of the computer is a LCD display, with one Power button.
Power Button

- 10 -
Getting Started
2.2.2. Rear View