Arbor Technology Rigid-750 User manual

Rigid-750 / Rigid-752
Intel® CoreTM i5-520M
Box PC
User’s Manual
Version 1.1
70
P/N: 4016075200110P 2014.11
70

This page is intentionally left blank.

- I -
Index
Chapter 1 - General Information..............................................1
1.1 Introduction................................................................2
1.2 Packing List................................................................2
1.3 The Installation Paths of CD Driver..........................4
1.4 Specications ............................................................4
1.5 Power Information .....................................................6
1.6 Dimensions ................................................................6
1.7 Locating Controls and Connectors..........................7
1.8 Connecting Peripherals ............................................9
1.8.1 VGA/DVI/DisplayPort Video Outputs.....................9
1.8.2 Serial Ports (COM1 ~4).........................................10
1.8.3 LAN Ports .............................................................. 11
1.8.4 USB Ports ..............................................................12
1.8.5 Keyboard and Mouse ...........................................13
1.8.6 Expansion PCIe Slots...........................................13
1.8.7 Audio Line-out/Mic-in ...........................................14
1.8.8 DC Power Input and Power ON/OFF Button.......15
Chapter 2 - The Engine of Rigid-750/Rigid-752....................17
2.1 Board Layout............................................................18
2.2 Jumpers and Connectors .......................................19
2.2.1 Jumpers & Connectors List.................................19
2.2.2 Jumper Setting......................................................20
SW1, 2, 4 (RS-232/RS-485 Function Select Jumper for
COM3, COM4)................................................................20
SW1 Setting................................................................... 20
SW2 Setting................................................................... 21
2.2.3 Pin Assignments for Connectors ........................21
PWRIN1 (Power Input)..................................................21
SW4 Setting................................................................... 21
CN1 (COM1 ~ COM4) ....................................................22
CBL-7100-COM (COM Converter Cable) (Optional) ... 23
VGA1 (CRT Display Connector)................................... 25
DP1 (DisplayPort Connector).......................................25
LAN1/2 (LAN Ports).......................................................26
USB1/2 (USB Ports) ......................................................26

- II -
Index
AUDIO1 (Audio Jacks)..................................................26
MC1 (PCIe Mini-card socket)........................................27
CPUF1/2 (Fan Connector) ............................................28
KBM1 (Keyboard & Mouse)..........................................28
CF1 (CFast Slot)............................................................28
DVI1 (DVI).......................................................................30
JSPI1 (System BIOS Enable/ Disable Pin Header,
factory use only) ...........................................................30
DIO1 (Digital I/O Port) ...................................................31
LPT1 (Parallel Port).......................................................31
SATA1/2 (Serial ATA Connectors)................................32
PWR1/2 (HDD/SSD Power Connectors) ......................32
Chapter 3 - Installation and Maintenance.............................33
3.1 CPU and Memory Module Installation ...................34
3.1.1 Removing Top Cover............................................34
3.1.2 Installing CPU .......................................................35
3.1.3 Installing Memory Module....................................36
3.1.4 Installing Memory Module with Thermal Pad.....37
3.1.5 Installing HSUPA 3.75G Module ..........................42
3.2 How to Access CFast/SIM Card..............................45
3.3 Hard Disk Drive and PCIe Card Installation ..........47
3.3.1 Removing Bottom Cover......................................47
3.3.2 Installing Hard Disk Drive ....................................47
3.3.3 Installing PCIe Card..............................................51
3.4 Wall Mounting ..........................................................52
3.5 Grounding the Box PC ............................................53
3.6 Wiring the DC-Input Power Source........................54
Chapter 4 - BIOS.....................................................................55
4.1 BIOS Main Setup......................................................56
4.2 Advanced Settings ..................................................57
4.2.1 ACPI Settings .......................................................59
4.2.2 CPU Conguration...............................................60
4.2.3 SATA Conguration .............................................62
4.2.4 Intel® IGD SWSCI OpRegion Conguration......63
4.2.5 USB Conguration...............................................64
4.2.6 Super IO Conguration .......................................65

- III -
4.2.7 PC Health Status..................................................66
4.2.8 Second Super IO Conguration .........................67
4.2.9 Platform Thermal Conguration.........................68
4.3 Chipset Settings ......................................................69
4.3.1 North Bridge.........................................................70
4.3.2 South Bridge Conguration................................71
4.4 Boot Settings ...........................................................72
4.5 Security.....................................................................74
4.6 Save & Exit ...............................................................76
Appendix .................................................................................79
Appendix A: I/O Port Address Map ..............................80
Appendix B: Interrupt Request Lines (IRQ) ................82
Appendix C: Memory Mapping.....................................83
Appendix D: Digital I/O Setting.....................................85
Appendix E: Watchdog Timer (WDT) Setting..............87
Index

- IV -
This page is intentionally left blank.

- i -
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this document may be reproduced by any me-
chanical, electronic, or other means in any form without prior written permis-
sion of the manufacturer.
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the di-
rectives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from ARBOR. Please contact
your local supplier for ordering information.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and

- ii -
used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are in
compliance and conform to the European Union’s Restriction of Use of Haz-
ardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main pur-
pose of the directive is to prohibit the use of lead, mercury, cadmium, hexava-
lent chromium, polybrominated biphenyls (PBB), and polybrominated diphe-
nyl ethers (PBDE) in electrical and electronic products. Member states of the
EU are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not con-
tain unintentional additions of lead, mercury, hex chrome, PBB or PBDB that
exceed a maximum concentration value of 0.1% by weight or for cadmium
exceed 0.01% by weight, per homogenous material. Homogenous material
is dened as a substance or mixture of substances with uniform composition
(such as solders, resins, plating, etc.). Lead-free solder is used for all termina-
tions (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the
earth we live, Arbor hereby conrms all products comply with the restriction of
SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH --Reg-
istration, Evaluation, Authorization, and Restriction of Chemicals) regulated
by the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- iii -
Important Safety Instructions
Read these safety instructions carefully
1. Read all cautions and warnings on the equipment.
2. Place this equipment on a reliable surface when installing. Dropping it or
letting it fall may cause damage
3. Make sure the correct voltage is connected to the equipment.
4. For pluggable equipment, the socket outlet should be near the equipment
and should be easily accessible.
5. Keep this equipment away from humidity.
6. The openings on the enclosure are for air convection and protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
7. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
8. Never pour any liquid into opening. This may cause re or electrical
shock.
9. Never open the equipment. For safety reasons, the equipment should be
opened only by qualied service personnel.
10. If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user’s manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
11. Keep this User’s Manual for later reference.

- iv -
Warning
The Box PC and its components contain very delicately Integrated Circuits
(IC). To protect the Box PC and its components against damage caused by
static electricity, you should always follow the precautions below when han-
dling it:
1. Disconnect your Box PC from the power source when you want to work on
the inside.
2. Use a grounded wrist strap when handling computer components.
3. Place components on a grounded antistatic pad or on the bag that came
with the Box PC, whenever components are separated from the system.
Replacing the Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
Technical Support
If you have any technical difculties, please consult the user’s manual rst
at: ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still can-
not nd out the answer.
http://www.arbor.com.tw
E-mail:[e-mail]
About This User’s Manual
This User’s Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User’s Manual, please consult your vendor before further
handling.

- v -
Warranty
This product is warranted to be in good working order for a period of one year
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by any
other related party.
Vendors disclaim all other warranties, either expressed or implied, including but
not limited to implied warranties of merchantability and tness for a particular
purpose, with respect to the hardware, the accompanying product’s manual(s)
and written materials, and any accompanying hardware. This limited warranty
gives you specic legal rights.
Return authorization must be obtained from the vendor before returned mer-
chandise will be accepted. Authorization can be obtained by calling or faxing
the vendor and requesting a Return Merchandise Authorization (RMA) number.
Returned goods should always be accompanied by a clear problem description.
Rigid-750 Fanless embedded controller w/ 1 x PCIex8 slot
Rigid-752 Fanless embedded controller w/ 1 x PCIex1 slot +
1 x PCIex16 slot
SSD-25080 Intel® 2.5" 80GB SATAII SSD kit
HSUPA-3500 HSUPA 3.75G module kit
WRK-GB320 WT DDR3 2GB SDRAM DIMM2 kit
Ordering Information

- vi -
This page is intentionally left blank.

- 1 -
General Information
1Chapter 1
General Information

- 2 -
General Information
1.2 Packing List
1.1 Introduction
Both Box PCs, Rigid-750 and Rigid-752, are targeted at many different
application elds. By adopting it, you can pinpoint specic markets, such as
Thin Client, KIOSK, information booth, GSM Server, environment-critical and
space-critical applications.
• All-In-One Platform
The CPU, DRAM and even software are integrated to provide a plug-
and-play machine.
• Compact-sized
The kernel of Rigid-750/Rigid-752 is FMB-i57M1, which is a non-
standard form factor embedded board. The whole system consumes
only a few space.
• Fanless and Modular CPU Board
By using a low power processor, the system does not have to rely on
fans, which are often unreliable and cause dust to circulate inside the
equipment. The modular design facilitates maintenance or possible
upgrades on the CPU board. Modular Box PC can be easily modied
to t many different applications according to customers' requests.
• Powerful Communication Capability
The Rigid-750/Rigid-752 provides COM, LPT, Ethernet, USB, Mini
Card slot, DVI and Digital I/O expansion slot.
• Numerous Display/Video Output
Integrated with Intel® HD Graphics core, Rigid-750/Rigid-752 improves
graphics and 3D rendering performance and supports numerous
display/video output options includes VGA and DisplayPort.
• Advanced Storage Solution
Rigid-750 / Rigid-752 comes with Compact Flash slot, which offers
a better, faster and more cost-effective expansibilities for various
applications.
• Trustworthy
The onboard Watchdog Timer can invoke an NMI or system RESET
when your application loses control over the system.
After opening the package, carefully inspect the contents. If any of the items is
missing or appears damaged, please contact with your local dealer or distributor.
The package should contain the following items:

- 3 -
General Information
Options:
The following items are normally optional, but some vendors may include
them as a standard package, or some vendors may not carry all the items.
Standard:
1 x Rigid-750 or Rigid-752 Box PC
1 x Accessory Box
(Driver CD/User’s Manual/Screws/
Cable/Terminal Block)
AC/DC Adapter Kit
Wall-mount Kit
COM Converter Cable (1 x 44-pin male to 4 x DB9 male
+ 1 x DB9 female) L=200mm
Intel® 2.5" 80GB SATAII SSD Kit
HSUPA 3.75G module kit
WT DDR3 2GB SDRAM DIMM2 kit

- 4 -
General Information
System Kernel
Processor Intel® CoreTM i5-520M
BIOS AMI Flash BIOS
Chipset Intel® QM57
Graphics Intel® HD Graphics
System Memory 2 x 204-pin Dual-channels DDR3 SO-DIMM Sockets up to 8GB at 800/1066MHz
(2GB WT DDR3-1333 SDRAM installed by default)
Serial ATA 2 x SATA 300MB/s
Expansion Bus
1 x Mini-card slot; 1 x SIM socket
1 x PCIex8 slot w/ riser card (Rigid-750 only )
1 x PCIex16 slot w/ riser card; 1 x PCIex1 slot w/
riser card (Rigid-752 only )
Ethernet
Controller
2 x Intel® WG82574IT Gigabit Ethernet controllers
Watchdog Timer 1 ~ 255 levels reset
I/O Ports
Serial Port • 4 x serial port via one DB-44 female connector
• COM1~COM4: RS-232 • COM3, 4: RS-232/485
1.4 Specications
1.3 The Installation Paths of CD Driver
Windows XP
Driver Path
CHIPSET \CHIPSET\INTEL\XP_32_64_WIN7_32_64_SERIES
VGA \GRAPHICS\INTEL_2K_XP_32\14425
LAN \ETHERNET\INTEL\XP_WIN7_SERIES\32
AUDIO \AUDIO\REALTEK_HD\WINDOWS_R252
ME \ME\6.1.0.1042_PV
Windows 7
Driver Path
CHIPSET \CHIPSET\INTEL\XP_32_64_WIN7_32_64_SERIES
VGA \GRAPHICS\INTEL_WIN7_VISTA_32\Win7Vista_15179
LAN \ETHERNET\INTEL\XP_WIN7_SERIES\32
AUDIO \AUDIO\REALTEK_HD\Vista_WINDOWS7_R251
ME \ME\6.1.0.1042_PV

- 5 -
General Information
*Selectable Port • 1 x LPT • 1 x 16-bit Digital I/O (8-in/8-out)
• 1 x DVI-D (default)
USB Port 8 x USB 2.0 ports
LAN Port 2 x RJ-45
Video Port 1 x DB-15 for Analog RGB; 1 x DisplayPort; 1 x DVI
KB/MS 1 x 6-pin Mini-DIN for keyboard & mouse
Audio Mic-in/Line-out (6W pre-amplied)
GSM/UMTS Up to HSUPA 3.75G (optional Mini-card)
Storage
HDD/SSD 1 or 2 x 2.5" drive bay for HDD or SSD w/ 9.5mm
height
CF 1 x CFAST socket (outside accessible)
Safety
FCC Class A certied
CE Certied
Environment
Operating Temp. -40 ~ 70ºC (-40 ~ 158ºF), ambience w/ air ow
Storage Temp. -40 ~ 85ºC (-40 ~ 185ºF)
Relative Humidity 10 ~ 95% @ 40oC (non-condensing)
Vibration 3 Grms/5 ~ 500 Hz/random operation
Shock & Crash
Operating 20G, 11ms; Non-operating 40G with HDD,
11ms
Operating 40G, 11ms; Non-operating 60G with
CFAST/SSD, 11ms
Crash 80G, 11ms
Mechanical
Construction Aluminum alloy
Mounting Wall mounting
Weight Rigid-750: 4.5 kg (9.9 lb); Rigid-752: 4.8 kg (10.56 lb)
Dimensions
(W x D x H)
Rigid-750: 195 x 268 x 90 mm (7.68" x 10.55" x 3.54")
Rigid-752: 195 x 268 x 110 mm (7.68" x 10.55" x 4.33")
* The selectable ports, including DVI-D, LPT and Digital I/O, are options
that only one of which can be equipped.

- 6 -
General Information
1.6 Dimensions
• Dimension (W x D x H): 195 x 268 x 110 mm (7.68" x 10.55" x 4.33")
• Dimension (W x D x H): 195 x 268 x 90 mm (7.68" x 10.55" x 3.54")
Rigid-750
Rigid-752
268.00
224.00
184.00
195.00
110.00
116.00
207.00
6.00
4.00
NUT
UNC #6-32
CFast / SIM
S/W
ACT1
LNK1
HDD
PWR
ACT2
LNK2
Unit: mm
DisplayPort
COM1~COM4
Optional
SW
DC IN
10V~28V
+ -
Ant.
268.00
224.00
184.00
195.00
90.00
96.00
207.00
6.00
4.00
NUT UNC #6-32
CFast / SIM
S/W
ACT1
LNK1
HDD
PWR
ACT2
LNK2
DisplayPort
COM1󲕏COM4
Optional
SW
DC IN
10V󲕏 28V
+ -
Ant.
Unit: mm
1.5 Power Information
Power Connector 1 x 4-pin DC input receptacle combined with
a power on/off switch for remote control
Input Voltage DC 10 ~ 28V
Power Consumption 120W (Max.)

- 7 -
General Information
CFast / SIM
S/W
ACT1
LNK1
HDD
PWR
ACT2
LNK2
HDD status LED
CFast/SIM Socket
USB Ports
LAN1 Active LED
LAN2 Active LED
Power Status LED
LAN1 Link LED
LAN2 Link LED
Keyboard/Mouse
Port
Power
On/Off
Switch
Front Panel
1.7 Locating Controls and Connectors
Please take a moment to identify those controls and connectors shown in the
following gures.
Both Rigid-750 and Rigid-752 have the same I/O ports and connectors at the
front panel.

- 8 -
General Information
Rear Panel
Rigid-750
Rigid-752
DisplayPort
COM1~COM4
Optional
SW
DC IN
10V~28V
+ -
Ant.
Antenna
Port
COM1~4
Ports
USB Ports
LAN Ports
VGA
DC-IN PCIe Slots
Line-out
Mic-in
DIO/LPT/DVI (Selectable)
DisplayPort
DisplayPort
COM1~COM4
Optional
SW
DC IN
10V~28V
+ -
Ant.
COM1~4
Ports USB Ports
LAN Ports
DC-IN PCIe Slot
Line-out
Mic-in
Antenna
Port VGA
DIO/LPT/DVI (Selectable)
DisplayPort