Arbor Technology P0715 User manual

Quick Installation Guide
Version 1.0
P0715
7" Compact Intel Low Voltage
PIII / Celeron Panel PC

2P0715 Quick Installation
Copyright©2006
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequen-tial damages arising from the use or inability to
use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
About this installation guide
This manual provides general information and installation instructions about the
product. This Quick Installation is intended for experienced users and integrators
with hardware knowledge of personal computers. If you are not sure about any
description in this Quick Installation, please consult your vendor before further
handling.

3
3
P0715 Quick Installation
Warning
Panel PC and their components contain very delicate Integrated Circuits
(IC). To protect the Panel PC and its components against damage from
static electricity, you should always follow the following precautions
when handling it :
1. Disconnect your Panel PC from the power source when you want to work on
the inside
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came with
the Single Board Computer, whenever components are separated from the
system
5. It possibly needs BIOS support in the case of using special backplane,
otherwise, it might be not able to function completely.
6. Please make sure the power connector is tightly plugged into the power
socket before power on.

4P0715 Quick Installation
Getting Started
This section will help you have your P0715 up and running
smoothly.
Before up and running, please make sure the package contains
all of above accessories.
If any of the above items is damaged or missing, contact your
vendor immediately.
P0715
PACKING LIST
9 x Screws
1 x Arm Holder Bracket
2 x Wall Mount Bracket
1 x Adaptor
2 x Power Cord (American & French Cordset)
1 x Driver CD

5
5
P0715 Quick Installation
Model Name
CPU Intel Low Voltage Celeron 400~733MHz CPU
FSB100/133MHz
Cache 2nd Level 256K
Memory 1 x 144Pin SO-DIMM up to 512MB SDRAM
VRAM SMI722 G8 Lynx 3D+ engine 8MB Video RAM on chip
Chipset Intel 815E + Intel CH2
ATA / IDE Ultra DMA 33, support 2 IDE device
Audio Realtek ALC202A AC97 Codec, support Line-out
Watchdog Timer 127-level Reset
System Fan 1 x 4cm x 4cm / 8 CFM
Serial Port 2 x RS-232 ports (COM1/2)
USB Port 2 x USB 1.1 compliant
KB / MS 1 x PS2 K/B and 1 x Mouse
Speaker 1 x speak out
LAN RJ45
Size / Type 7" TFT Color LCD
Max. Resolution 800 x 480, SVGA
Pixel Pitch 0.3075mm x 0.3075mm
Touch Screen 7" 4Wire Resistive (USB Interface)
Viewing Angle 160° (V), 160° (H)
Luminance (cd/m2)300
Back Light MTBF 50,000 hours
HDD / Type 1 x built-in 2.5" vibration Resistant HDD bay
Flash Disk 1 x Type II Compact Flash Disk Socket (Internal)
Output rating 63W
Input voltage DC 12V Input
Operating Temp. 0°C ~ 50°C
Storage Humidity 5% ~ 95%, non condensing
Vibration 17~500 Hz, 1G PTP
Shock 10G/peak (11m sec)
Construction Heavy-duty steel & Aluminum (Front bezel)
Weight 1.9kg (4.18 lb)
Dimension (L x H x D) 227 x 158 x 76mm
Storage
Power Supply
Mechanical &
Environmental
Specification
System
I/O
LCD Display
Panel PC P0715

6P0715 Quick Installation
Mounting
Hook Mounting
Arm Mounting

7
7
P0715 Quick Installation
Dimension
Unit: mm

8P0715 Quick Installation
OSD of Front Panel

9
9
P0715 Quick Installation
Location of I/O Ports
Before starting to install software on your new Panel PC please spend some
time to find out the exact location of connectors and HDD (if pre-installed). The
front panel does not contain any indicators, switches, connectors or drive
access. All these are to be found on the left and right side and on the rear of the
system.
Default I/O

10 P0715 Quick Installation
Connecting Peripherals
The user can use the I/O interfaces located at the backside of the chassis to
connect external peripheral devices, such as a mouse, a keyboard, a monitor,
serial devices or parallel printer etc. Before connection, make sure that the
computer and the peripheral devices are turned off.
Connecting an external CRT
P0715 has a 15-pin analog RGB interface connec-
tor located at the rear side of the chassis. As to
resolution, P0715 otputs 800 x 480 instead of 800
x 600, it won't display completely at first when
you connect the monitor.
External Serial Ports (COM1/2)
The P0715 logic board supports four onboard serial ports, all COM ports
supports RS-232.
The external COM1, COM2 are all D-SUB 9-pin
connectors. To connect any serial device, follow
the following instructions:
1. Turn off the Panel PC system and the serial
devices.
2. Attach the interface cable of the serial device to the 9-pin D-SUB serial
connector. Be sure to fasten the retaining screws.
3. Turn on the computer and the attached serial devices.
4. Refer to the serial device's manual for instruction to configure the operation
environment to recognize the new attached devices.
5. If the serial device needs specified IRQ or address, you may need to run the
CMOS setup to change the hardware device setup.
Speaker Jack
P0715 has one speaker jack.