ARC LYCT-505 User manual

Version 2.
pecification:
Function: 16 Channel wireless remote control
Group ON/OFF Function
Frequency: 433.92MHz
Battery: 3V CR2032 Lithium Cell Battery
verview:
Compact 16 channels hand held remote control with the ability to control your lighting system
wirelessly.
With 4 sets of ON/OFF button, 1 set of group ON/OFF function and a slide switch to select 4
channels.
S
O
Wireless Remote Control
LYCT-505

Version 2.
aring:
Hand held remote control can memorize unlimited receivers into the 16 channels.
Pairing using LEARNING MODE:
1. First choose the desired receiver(s) that you wish to control.
2. Press the ‘Learn’ button once (LED will flash), this will now enter learning mode.
3. On the remote control press the ‘ON’ button intended to be paired; the load will flash twice to
confirm that the remote control is now paired.
＊To pair two or more receivers as a group, during the learning mode press the ‘Group ON’button
instead.
NOTE: Learning mode lasts for 12 seconds; if no signal is given to the receiver then it will
automatically exit learning mode without pairing the device.
To exit learning mode manually, simply press the ‘Learn’ button again.
！If, during learning mode the load does not flash to confirm, this means that the receiver’s memory
is FULL and no further remote control may be paired unless one of the existing remote control is
first unpaired (see below).
nparing:
Removing single device:
1. With the receiver that you intent to un-pair press the ‘Learn’ button once (LED will flash), this
will now enter learning mode.
2. On the remote control press the ‘OFF’ button intended to be unpaired; the load will flash twice to
confirm that the remote control is now unpaired.
＊To un- paired receiver(s) from a group, during the learning mode press the ‘Group OFF’button
instead.
P
U

Version 2.
peration:
If you wish to use more than 4 memories, the I / II / III / IV slide switch at the bottom of the remote
control must be used. Each channel can store up to 4 memories.
Slide Switch.
Slide switch allows the remote control to transmit up to 16 commands.
By using the slide switch, the 4 ON/OFF buttons can each transmit 4 signals. i.e. ON/OFF button 1
transmits to receivers paired when slide switch at position I, ON/OFF button 1 transmits to receivers
paired when slide switch at position II etc..
ON/OFF Function:
Press the ‘ON’button on remote control, the lights will gradually illuminate.
Press the ‘OFF’button on remote control, the light will gradually turn OFF.
Group ON/OFF Function:
Press the ‘Group ON’button on remote control, the group of lights you first set up will gradually
illuminate.
Press the ‘Group OFF’button on remote control, the group of lights you first set up will gradually
turn OFF.
Dimming Function: (not available under ‘Group’button)
1. Make sure load is switched ON.
2. On the remote control press the ON button again, the loads will start to dim.
3. To stop at the desired brightness level, press the ON button again.
※Dimming level dims in cycle, during the cycle if no signal is given, after 4 cycles it will stop at
100% brightness.
！After setting a dim level using the remote control the light is then switched OFF, the next time that
the light is switched back ON again the load will return to the previous stipulated brightness.
O

Version 2.
attery Replacement:
3V CR2032 lithium battery is included.
When the battery voltage is low, the transmission range will be reduced accordingly.
Slide down battery cover and with a screw driver push out the battery.
Replace with a new battery then slide up the battery cover.
roubleshoot:
Problem: The LED on remote control does not light up.
Solution:Please check if the battery is inserted correctly or replace a new battery.
Problem:I cannot pair my remote control with the receiver.
Solution:The memory on receiver is full, please delete one or more memory and try pairing again.
B
T