Arctiko LCF 100 User manual

OPERATING INSTRUCTIONS
LCF 100/200/300/400/500

2

3
INDEX...........................................................PAGE
User Instructions
Dixell XT111C for LCF models ..........................................................8
Generalwarning...................................................................8
Generaldescription ................................................................9
Firstinstallation ...................................................................9
Front panel commands ...............................................................10
List of parameters ...................................................................13
Alarms .............................................................................13
Probes and display ..................................................................14
Digital input ........................................................................15
Other ..............................................................................15
Installation and mounting .............................................................15
Alarm signals .......................................................................17
Connections ........................................................................18
Default setting values ................................................................19
Wiring diagram for LCF 100 / 200 / 300 ..................................................20
Wiring diagram for LCF 400 / 500 .......................................................21
.....................................................................4

4
USER INSTRUCTIONS
Congratulations on your new low temperature freezer. We trust that it will serve you for many years to come.
In order to gain optimum benefit from your freezer, please read the following instructions thoroughly and act
accordingly. The low-temperature freezers are used for freezing and long-term storing of medical prepara-
tions ( vaccines, blood plasm, ect.) and other biological products.
1. Environmental protection and disposal.
The packaging is designed to protect the appliance and its components during transportation, and it is made
of recyclable materials.
• Please return the packaging to an official collection point for recycling.
• Old appliances contain reusable materials and should not be disposed of together with household
refuse.
• Remove the spring-action hinges from the appliance, in order to prevent children from being entrapped
in the appliance.
• Ensure that no part of the refrigeration tubing is damaged as the refrigerant in the appliance risks
escaping to the environment.
• Information about refrigerant type and amount will be found on the type plate on the rear of the
appliance (Fig. 1).
2. Safety instructions.
• In order to prevent injuries and or damage to the appliance, it should be unpacked and set up by min.
two people.
• If upon unpacking the appliance is found damaged, do not connect to the mains, but contact the
supplier.
• Interference with or repair to the appliance should only be carried out by authorized personnel, in order
to avoid any injuries. (contact the supplier for further information).
• Never put naked flames or other ignition sources inside the appliance.
• Never touch the freezers interior or products in the freezer when the freezer is operating. Use gloves or
alike in order to avoid injuries (frost-bite).
• Keep the key to the appliance away from the appliance and out of the reach of children.
3. IMPORTANT NOTE !!!
• The type of refrigerant in the –60°C freezers, is a mixture of different flammable hydrocarbons. These
freezers are designed and tested according to the EN 378 standard, under clause A3 room and L3
refrigerants, this means that the volume of the room where the freezers is placed must have a volume
of minimum 40m3 corresponding to approx. 4m2 in a room with a normal floor height.
4. Connection to the mains.
• For safety reasons the appliance must be earthed. If you are in any doubt, please contact an
authorized electrician.
• The appliance should be left for 5 hours before it is connected to the mains. If the appliance is
connected before that, there is a risk of damaging the compressor.

5
• If for any reason the appliance is disconnected from the mains, please wait 10 minutes before re-
connecting. The electronic starting device needs this time to cool down, before a safe re-start can be
made.
5. Before use.
• Before use, the interior of the appliance should be cleaned with a mild soap solution, and wiped off
with a dry clean cloth. Never use any kind of solvent or other chemicals.
6. Setting up the freezer.
The freezer should not be placed where it might be splashed with
water, in extreme high humidity or in direct sunlight. Any of these
factors may lead to a reduction in performance and shorten the life
span of the components. The freezer should be placed on a horizontal
level, and should not be placed close to a heating appliance or
heating tubes. Allow a minimum of 50mm (2”) clearance on the side
and the back. The side with the ventilation grill should have a
clearance of at least 100 mm (4”) in order to allow the heat from the
compressor motor to dissipate. Underneath the appliance there
should be a gap of 15 mm approx. (1/2”). On a soft surface, e.g. carpet, it may be necessary to ensure the
correct distance by means of spacers.
7. Electrical supply.
The electrical supply should always be in accordance with the rating
plate on the back of the freezer. The supply must always be in
accordance with the law and regulations regarding electrical safety, if
any doubts contact your supplier.
8. Starting Up.
In case the compressor does not start when the freezer has been plugged in, the electrical supply may not
be in order. Check if there is an electricity supply to the plug or if the fuse is blown. If not please go to
trouble shooting page 6. 18.
9.Operating the freezer
The empty freezer should be switched on for at least 5-6 hours prior to loading of the freezer. The freezer
should not be loaded above the inside walls which is also the load line limit.
Please note: After the lid has been opened, there will be a vacuum created inside the freezer due to the
low temperatures. Wait a few minutes before trying to reopen the lid otherwise the handle could be
damaged.

6
10.Defrosting.
In order for the freezer to work to its maximum efficiency the cabinet
should be defrosted when a approx. 2mm thick ice layer has formed
inside the cabinet. The ice layer is easily removed with a plastic or
wooden scraper. Never use a sharp metal object which might will
cause damage to the inner liner. The defrosting frequency is
determined mainly by two factors the usage pattern (number of lid
openings) and the relative humidity. Excess water can be drained out
by using the drain water outlet on the front of the freezer.
11.Cleaning.
Cleaning should be done when needed. When used in a dirty
environment it might be necessary to remove the compressor
compartment grill, and clean the compressor compartment eventually
with a vacuum cleaner. If the cleaning process is neglected there is a
risk that the performance of the freezer will be effected, and even
damage to the compressor could occur due to overheating.
12. Storage.
If the freezer is stored for a period of time, the lid should be kept open for free circulation of air inside the
cabinet in order to avoid corrosion of the inner liner.
13. Temperature control LCF- freezers.
The temperature inside the freezer is controlled by the electronic controller in the front grill. The controller
has a digital readout of the temperature inside the cabinet. and the option of changing the temperature
inside the cabinet.
14. External voltage and temperature alarm.
Optionally the freezer can be equipped with a battery operated alarm box with connections for external
alarm for voltage failure and temperature alarm. The battery should be exchanged every two years.
Please note! When commissioning the freezer, the battery must be turned into its correct position. More
details on page 17.
15. Dixell controller (XT111C)
60.0
°C
-
•

7
16. Functions.
How to see the set point:
1.Press and immediately release the SET key, the display will now show the set point value.
2.Press and immediately release the SET key or wait for 5 seconds to display the probe value again.
How to lock and unlock the keyboard
1.Press the up and down keys simultaneously for more than 3.seconds.
How to change the set point
1.Press the SET key for more than 3.seconds to change the set point value.
2.The set point value will be displayed and the LED starts flashing.
3.To change the set point value, push the up or down arrow.
4. To memorise the new setting press the SET key again or wait 15 seconds for the controller to return
to normal display of the probe temperature.
17. Setting the controllers offset value
The LCF freezer is designed for long time and safe storage of sensitive products. In some situations the
LCF freezer is also used for other applications like in laboratories for different low temperature test.
Depending on the actual situation it might be necessary to change the controllers offset value in order to
get a correspondence between the reading on the display and the actual temperature inside the cabinet.
The factory setting is an offset of 2 dgr:C. The offset can be adjusted in the following way.
Unlock the keyboard.
Enter the programming mode by pressing the SET and arrow down keys for 3 seconds.
Select the parameter “Opb” by pressing arrow up or down key.
Press the SET key to display its value.
Use arrow up or down to change its value. The offset can be adjusted to +/- 12 dgr .C
Press SET to store the new value.
Press SET + arrow up or wait 15 seconds without pressing any key. The new value will now be stored.
For more detailed information about programming the Dixell controllers please consult the attached
manuals.
18. Trouble shooting.
The appliance is not operating. Please check:
Is the electrical plug connected to the mains (wall socket)? Has the fuse blown?
The temperature inside the appliance is too high. Please check:
Is the Dixell controller set to the correct temperature?
Has an excess amount of ice formed inside the appliance?
The appliance is operating continuously. Please check:
Is the ambient temperature very high?
Has the appliance recently been loaded with a large amount of warm products?
If you have checked the above points and the appliance is still not working as expected, please contact
your local dealer for further advice.

8
19. LN 2 or LCO 2 back-up
On the rear side of the cabinet there is a label and a marking, where it is possible to insert either a
temperature probe or a backup LN2 or LCO2 supply. The inner and outer skins are pre-drilled.
DIXELL XT111C FOR LCF MODELS
GENERAL WARNING
Please read before using this manual
• This manual is part of the product and should be kept near the instrument for easy and
quick reference.
• The instrument shall not be used for purposes different from those de scribed hereunder.
It cannot be used as a safety device.
• Check the application limits before proceeding.
Safety Precautions
• Check the supply voltage is correct before connecting the instrument.
• Do not expose to water or moisture: use the controller only within the operating limits
avoiding sudden temperature changes with high atmospheric humidity to prevent
formation of condensation
• Warning: disconnect all electrical connections before any kind of maintenance
• The instrument must not be opened.
Back-up inlet
IMPORTANT NOTE !!!
Do not attempt to drill or in other way make access to
the freezers interior other places than at the marking,
there is a risk of damaging the freezers tubing
system, resulting in a leakage with inflammable
gasses.
XT111C
Single Stage Digital Controller For Temperature

9
• In case of failure or faulty operation send the instrument back to the distributor with a
detailed description of the fault.
• Consider the maximum current which can be applied to each relay (see Technical
Data).
• Ensure that the wires for probes, loads and the power supply are separated and far
enough from each other, without crossing or intertwining.
• In case of applications in industrial environments, the use of mains filters (our mod.
FT1) in parallel with inductive loads could be useful.
GENERAL DESCRIPTION
The XT110C and XT111C are single-stage ON/OFF controllers for temperature, humidity and pressure
applications with direct or inverse action, user-selectable. The analogue input type can be set by
parameter between the following, according to the model:
- PTC, NTC;
- PTC, NTC, Pt100, Thermocouple J, K, S;
- 4÷20mA, 0÷1V, 0÷10V.
FIRST INSTALLATION
Probe setting
The pre-set probe type is written on the label of the instrument, see picture.
If it is different from theprobe that has be used, set the probe following
procedure below
How to set the probe.
1. Enter the programming menu by pressing the SET+ n for 3s.
2. Select the Pbc (Probe configuration) parameter and push the SET key.
3. Set the kind of probe:
a. Controller for temperature: Pt= Pt100, J = J thermocouple, c = K thermocouple, S = S
thermocouple; Ptc = PTC; ntc = ntc
b. Controller with current or voltage inputs: cur=4÷20mA, 0- 1= 0÷1V, 10= 0÷10V
4. Push the SET key to confirm it.
5. Switch the controller off and on again
NOTE: Before proceeding check and, if necessary; set with appropriate values the
Minimum Set Points (LS1 e LS2) and Maximum Set Points (US1 e US2). See also the
paragraphs concerning the programming.

10
Front panel commands
SET:
To display and modify target set point; in programming mode it selects a parameter or confirm an
operation.
TO SWITCH THE INSTRUMENT ON/OFF: If the function is enabled (par. onF=yES), by pressing the SET
key for more than 4s the controller is switched OFF. To switch the instrument on again press the SET key.
o UP: in programming mode it browses the parameter codes or increases the displayed value. Hold it
pressed for a faster change
n DOWN: in programming mode it browses the parameter codes or decreases the displayed value. Hold
it pressed for a faster change
KEY COMBINATIONS:
o + n To lock & unlock the keyboard.
SET + n To enter in programming mode.
SET + o To return to the room temperature display.
Use of LEDS
A series of light points on the front panels is used to monitor the loads controlled by the instrument. Each
LED function is described in the following table.
LED2 E.S. LED1
LED
LED1
LED2
E.S.
MODE
ON
flashing
flashing
ON
ON
FUNCTION
Output relay enabled
- Programming Phase (flashing with LED2)
- Programming Phase (flashing with LED1)
Energy saving activated by digital input
- ALARM signal
- In “Pr2" indicates the parameters is also present in “Pr1"

11
TO see THE SETPOINT
1. Push and release the SET key to see the Set point value;
2. To come back to the normal display push again the SET key or wait 10s.
TO CHANGE THE SETPOINT
1. Hold pushed the SET key for 3s to change the Set point value;
2. The value of the set point will be displayed and the LED1 & 2 start blinking;
3. To change the Set value push the o or n arrows within 10s.
4. To memorise the new set point value push the SET key again or wait 10 s.
TO enter the parameters list “Pr1”
To enter the parameter list “Pr1” (user accessible parameters) operate as follows:
1. Push for 3s the SET + n keys (LED1 & 2 start blinking).
2. The controller will display the first parameter present in the Pr1 menu..
TO ENTER the parameters list “Pr2”
The “Pr2” parameter list contains the configuration parameters. A security code is required to enter it.
1. Enter the “Pr1” level, see above paragraph.
2. Select “Pr2” parameter and press the “SET” key.
3. The “PAS” flashing message is displayed, shortly followed by “0 - -” with a flashing zero.
4. Use o or n to input the security code in the flashing digit; confirm the figure by pressing “SET”. The
security code is “321”.
5. If the security code is correct the access to “Pr2” is enabled by pressing “SET” on the last digit.
Another possibility is the following:
After switching ON the instrument, within 30 seconds, push SET + n keys together for 3s: the Pr2 menu
will be entered.
HOW TO MOVE A PARAMETER FROM THE “PR2” MENU TO “PR1” AND VICEVERSA.
Each parameter present in “Pr2” MENU can be removed or put into “Pr1”, user level, by pressing “SET + n”.
In “Pr2” when a parameter is present in “Pr1” the LED is on.

12
HOW TO CHANGE a parameter
To change a parameter value operates as follows:
1. Enter the Programming mode
2. Select the required parameter.
3. Press the “SET” key to display its value.
4. Use “UP” or “DOWN” to change its value.
5. Press “SET” to store the new value and move to the following parameter.
TO EXIT: Press SET + UP or wait 15s without pressing a key.
NOTE: the set value is stored even when the procedure is exited by waiting the timeout to expire.
HOW TO LOCK THE KEYBOARD
1. Keep pressed for more than 3 s the the o and n keys.
2. The “POF” message will be displayed and the keyboard will be locked. At this point it will be
possible only to see the set point or the MAX o Min temperature stored
3. If a key is pressed more than 3s the “POF” message will be displayed.
TO UNLOCK THE KEYBOARD
Keep pressed together for more than 3s the the o and n keys, till the “Pon” message will be displayed.
ON/OFF function
TO SWITCH THE INSTRUMENT ON/OFF:
If the function is enabled (par. onF=yES), by pressing the SET key for more than 4s the controller is
switched OFF. To switch the instrument on again press the SET key.
PROBES AND MEASURING RANGE
Probe
NTC
PTC
Pt100
TcK
TcJ
TcS
Down Scale
-40°C/-40°F
-50°C/-58°F
-200°C/-328°F
0°C/32°F
0°C/32°F
0°C/32°F
Full Scale
110°C/230°F
150°C/302°F
600°C/1112°F
1300°C/1999°F
600°C/1112°F
1400°C/1999°F

13
List of Parameters
REGULATION
Hy1
Differential: (-Full Sc. / Full Sc.) Intervention differential for set point. It can be set with positive value or
with negative value. The kind of action (direct or inverse) depends on the S1C parameter (in or di).
LS1
Minimum set point: (Down Sc.÷ Set) Sets the minimum acceptable value for the set point. Us1
Maximum set point: (Set÷ Full Sc.) Sets the maximum acceptable value for set point.
S1C
Action type: S1C=in inverse action (heating/ humidifying/increase pressure); S1C=dir direct action
(cooling /dehumidifying/decrease pressure).
AC
Anti-short cycle delay: (0÷250 sec) Minimum time between the switching off and the following switching
on
on
Minimum time a stage stays switched ON
(0÷250 sec)
ono:
Minimum time between 2 following switching ON of the same load
(0÷120 min).
ALARMS
ALC
Temperature alarms configuration: it determines if alarms are relative to set point or referred to
absolute values. rE relative to set point; Ab absolute temperature
ALL
Minimum alarm:
with ALC=rE: relative to set point, (0÷|Down Sc.-Set|) this value is subtracted from the set point. The
alarm signal is enabled when the probe values goes below the “SET-ALL” value. with ALC=Ab absolute
value, minimum alarm is enabled when the probe values goes below the “ALL” value.
ALU
Maximum alarm:
with ALC=rE: alarm relative to set point, (0÷|Full Sc.-Set|) Maximum alarm is enabled when the probe
values exceeds the “SET+ALU” value. with ALC=Ab: absolute alarm, (Set÷Full Sc.) Maximum alarm is
enabled when the probe values exceeds the “ALU” value.
ALH
Differential for alarm recovery: (0,1÷Full scale) the alarm recovers when probe value is higher than
Alarm value + ALH.

14
ALd
Alarm delay:(0÷999 min) time interval between the detection of an alarm condition and alarm signalling.
dAO
Delay of alarm at start-up: (0÷23.5h) time interval between the detection of the alarm condition after
instrument power on and alarm signalling.
So1
Relay status with faulty probe: So1=oFF open; So1=on closed.
tbA
Status of alarm relay after pushing a key.
(XT111C only):
oFF = relay disabled; on = relay enabled.
AS
Alarm relay configuration (XT111C only):
cL = 4-6 terminals open with alarm; oP = 4-6 terminals closed with alarm.
PROBES AND DISPLAY
LCI
Start of scale, only with current or voltage input: (-1999÷1999) Adjustment of read out corresponding to
4mA or 0V input signal.
UCI
End of scale, only with current or voltage input: (-1999÷1999) Adjustment of read out corresponding to
20mA or 1V or 10V input signal.
oPb
Probe calibration: (-999÷999) allows to adjust possible offset of the probe.
rES
Decimal point ON/OFF: (rES=in OFF; rES=dE ON; rES= cE with 2 decimal points, only for current or
voltage input) select the resolution of the controller.
NOTE: the decimal point selection is not available on models with thermocouple input.
UdM
Measurement unit: it depends on models:
for temperature:°C = Celsius; °F = Fahrenheit.
with 4÷20mA, 0÷1V, 0÷10V input : 0= °C; 1= °F, 2= %RH, 3=bar, 4=PSI, 5=no measurement unit.
PbC
Probe selection: it sets the kind of probe. It depends on models
for temperature NTC/PTC: Ptc = PTC; ntc = ntc.
for temperature standard: Pt= Pt100, J = J
thermocouple, c = K thermocouple, S = S
thermocouple; Ptc = PTC; ntc = ntc.
with 4÷20mA, 0÷1V, 0÷10V input: cur=4÷20mA, 0-1= 0÷1V, 10= 0÷10V.
P3F
Third wire presence for Pt100 probe: for using 2 or 3 wires Pt100 probes: no = 2 wires probe; yES = 3
wires probe.

15
DIGITAL INPUT
HES
Set point change during during the Energy Saving cycle: (Down Sc./Full Sc.) sets the variation of the
set point during the Energy Saving cycle.
i1F
Digital input operating mode: configure the digital input function: c-H = to invert the kind of action: direct -
reverse;
oFF = to switch the controller off.; AUS = Not used; HES = Energy Saving;
EAL = generic external alarm; bAL = serious external alarm: it switches off the loads.
i1P
Digital input polarity:
CL: the digital input is activated by closing the contact;
OP: the digital input is activated by opening the contact
did
Digital input alarm delay: (0÷255 min) delay between the detection of the external alarm condition (i1F=
EAL or i1F = bAL) and its signalling.
OTHER
Adr
RS485 serial address (0÷247) identifies the instrument within a control or supervising system.
onF
Swithching ON/OFF enabling from keyboard: (no = disabled; yES=enabled) It permits the switching
ON/OFF of the instrument by pressing the SET key for more than 4s.
Ptb
Parameters table: (read only) Shows the code of the parameters map.
rEL
Software release: (read only)
Pr2
To access the Pr2 parameter programming menu.
Installation and mounting
Instrument XT110C and XT111C shall be mounted on vertical panel, in a 29x71 mm hole, and fixed using
the special brackets supplied.

16
To obtain an IP65 protection grade use the front panel rubber gasket (mod. RG-C) as shown in figure. The
temperature range allowed for correct operation is 0÷60 °C. Avoid places subject to strong vibrations,
corrosive gases, excessive dirt or humidity. The same recommendations apply to probes. Let air circulate
by the cooling holes.
Electrical connections
The instruments are provided with screw terminal block to connect cables with a cross section up to 2,5
mm². Before connecting cables make sure the power supply complies with the instrument’s requirements.
Separate the input connection cables from the power supply cables, from the outputs and the power
connections. Do not exceed the maximum current allowed on each relay, in case of heavier loads use a
suitable external relay.
Serial connections
All models can be connected to the monitoring and supervising system Xj500 using the serial port. The
external Xj485 serial module to interface the instrument with the monitoring and supervising system Xj500
is required. The standard ModBus RTU protocol it is used.
NOTE: Instruments with current or voltage input and 230V or 115V supply, cannot be connected to the
XJ485 serial module.
How to use the HOT KEY
How to program a hot key from the instrument (UPLOAD)
1. Program one controller with the front keypad.
2. When the controller is ON, insert the “Hot key” and push o key; the “uPL” message appears
followed a by flashing “End”
3. Push “SET” key and the End will stop flashing.
4. Turn OFF the instrument remove the “Hot Key”, then turn it ON again.
NOTE: the “Err” message is displayed for failed programming. In this case push again o key if you want to
restart the upload again or remove the “Hot key” to abort the operation.
HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD)
1. Turn OFF the instrument.
2. Insert a programmed “Hot Key” into the 5 PIN receptacle and then turn the Controller ON.
3. Automatically the parameter list of the “Hot Key” is downloaded into the Controller memory, the
“doL” message is blinking followed a by flashing “End”.
4. After 10 seconds the instrument will restart working with the new parameters.
5. Remove the “Hot Key”..
NOTE: the message “Err” is displayed for failed programming. In this case turn the unit off and then on if
you want to restart the download again or remove the “Hot key” to abort the operation.

17
Digital input
XT110C and XT111C have 1 free contact digital input. It is programmable in 5 different configurations by
the “i1F” parameter.
invert the kind of action: heatingcooling (I1F = C-H)
This function allows to invert the regulation of the controller: from direct to inverse and viceversa.
REMOTE ON/OFF (I1F = OFF)
This function allows to switch ON and OFF the instrument.
GENERIC ALARM (i1F = EaL)
As soon as the digital input is activated the unit will wait for “did” time delay before signalling the “EAL”
alarm message. The outputs status don’t change. The alarm stops just after the digital input is deact
vated.
serious alarm mode (I1F = BAL)
When the digital input is activated, the unit will wait for “did” delay before signalling the “bAL” alarm
message. The relay outputs are switched OFF. The alarm will stop as soon as the digital input is de
activated.
energy saving (I1F = HES)
The Energy Saving function allows to change the set point1 value as the result of the SET1 + HES
(parameter) sum. This function is enabled until the digital input is activated.
ALARM SIGNALS
alarm relay status (Xt111c)
Silencing buzzer / alarm relay output
Once the alarm signal is detected the buzzer, if present, can be disabled by pressing any key.
Message
“PFo”
“PFc”
“HA”
“LA”
“EAL”
“bAL”
Cause
Probe broken or absence
Probe short circuited
Maximum alarm
Minimum alarm
External alarm
Serious external alarm
Outputs
Alarm output ON; Output according to Parameter “So1"
Alarm output ON; Output according to Parameter “So1"
Alarm output ON; Other outputs unchanged
Alarm output ON; Other outputs unchanged
Output unchanged
Output OFF
Status of the instrument
Instrument off
Normal operating
Alarm present
AS = CL
4-6 closed
4-6 closed
4-6 open
AS = oP
4-6 closed
4-6 open
4-6 closed

18
XT111C: the alarm relay status depends on the tbA parameter: with tbA=yES the relay is disabled by pressing any
key, with tbA=no the alarm relay remains enabled as long as the alarm lasts. The display signal remains as long as
the alarm condition remains.
Alarm recovery: Probe alarms “PFo”, “PFc” start few seconds after the fault in the probe; they automatically stop
few seconds after the probe restarts normal operation. Check connections before replacing the probe. Max. and
min. alarms “HA” and “LA” automatically stop as soon as the variable returns to normal values. Alarms “bAL” and
“EAL” recover as soon as the digital input is disabled.
Technical data
Housing: self extinguishing ABS.
Case: frontal 32x74 mm; depth 60mm;
Mounting: panel mounting in a 71x29 mm panel cut-out.
Protection: IP20.
Frontal protection: IP65 with frontal gasket RG-C (optional).
Connections: Screw terminal block £ 2,5 mm² heat-resistant wiring.
Power supply: 12Vac/dc, ±10% or: 24Vac/dc ± 10% or 230Vac ± 10%, 50/60Hz or
110Vac, ± 10%, 50/60Hz
Power absorption: 3VA max.
Display: 3 1/2 digits, red LED
Inputs: according to the order: NTC/PTC or NTC/PTC /Pt100/Thermo
couple J, K, S or 4÷20mA/ 0÷1V / 0÷10V
Relay outputs: Load relay SPDT 8(3)A, 250Vac
Alarm: (XT111C) relay SPDT 8(3)A, 250Vac
Other output: buzzer (optional)
Kind of action: 1B; Pollution grade: normal, Software class: A.
Data storing: on the non-volatile memory (EEPROM).
Operating temperature: 0÷60 °C (32÷140°F).
Storage temperature: -30÷85 °C (-22÷185°F).
Relative humidity: 20÷85% (no condensing)
Measuring and regulation range: according to the probe
Controller Accuracy a 25°C: better than ±0,5% of full scale
Connections

Default setting values
19
COD
Set
Hy1
LS1
US1
S1C
Ac
on
ono
ALC
ALL
ALU
ALH
ALd
dAO
So1
tba¹
AS¹
Lci²
Uci²
OPb
rES
UdM
PbC
P3F
HES
i1F
i1P
did
Adr
OnF
Ptb
rEL
Pr2
°C/°F
0/32
-1/-2
min
max
in
0
0
0
rE
10.0/ 20
10.0/ 20
2.0/4
15
1.3
oFF
yES
oP
various
various
0.0
in
various
various
no
0.0
EAL
cL
0
1
no
--
--
321
Lev
-
Pr1
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr1
Pr1
Pr1
Pr2
Pr1
Pr1
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr2
Pr1
Name
Set point
Differential
Minimum set point
Maximum setpoint
Action type output
Anti-short cycle delay
Minimum time a stage stays switched ON
Minimum time between 2 following switching
ON of the same load
Alarm configuration
Minimum alarm (ALC=rE)
(ALC=Ab)
Maximum alarm (ALC=rE)
(ALC=Ab)
Alarm recovery differential
Alarm delay
Alarm delay at start up
Output status with faulty pr.
Alarm relay disabling
Alarm relay polarity
Start scale with current or voltage input
End scale with current or voltage input
Probe calibration
Resolution
Measurement unit
(temp.)
(current/voltage)
Kind of probe
3rd wire presence
Energy saving differential
Digital inputconfiguration
Digital input polarity
Alarm delay for dig. input
Serial adress
oFF function enabling
Parameter table
Software release
To access the Pr2
Range
LS1+US1
-Full Sc./Full Sc.
Down Sc./Set
Set/Full Sc.
in=Inverse; dir=directed
0 -250 sec.
0 -250 sec.
0 -120 min.
rE=relat.; Ab=absolute
0 +[Start Sc.-Set].
Start Sc.+ALu
0 +[Full Sc.-Set]
ALL+Full scale
0 -Full scale
0 -999 min
0 -23h 50 min
oFF=open on=closed
no; yES
CL + oP
-1999 -1999
-1999 -1999
-Full Sc./Full Sc.
in=NO; dE=0,1; cE=0,01
°C=°C; °F;
0=°C; 1=°F; 2=HR; 3=bar;
4=PSI; 5=off
PT=Pt100; J=tcJ; c=tck;S=tcS; Ptc=PTC;
ntc=NTC; 0-1=0-1V; 10=0+10V; cur=0-20mA
no=2 wires; yES=3wires
Down SC./Full Sc.
c-H/oFF/AuS/HES/EAL/bAL
cL=closed; oP=open
0-120 m
0-247
no=not enabled; yES=enabled
Readable only
Readable only
Readable only

Wiring diagram for LCF 100 / 200 / 300
20
230V
50/60 HZ
Power supply
Fan
Starting device
Compressor
Dixell XT111C 230V Controller
Line No Nc
B A
Censor