ARGON18 NITROGEN DISC 286A User manual

NITROGEN DISC 286A: ASSEMBLY GUIDE
Valid for MY2019 Nitrogen Disc 286A
Revision 1.0 - 07-26-2018

1. Tools Needed and First Aid Kit ...........................3
2. Frameset inspection .....................................4
3. Frameset Parts, SKUs and descriptions ..................5-6
4. Assembly instructions ................................7-22
4.1. Headset Installation ...............................7-9
4.2. Seat Post Installation................................10
4.3. Seat Post Assembly .................................11
4.4. Front Derailleur Adjustement .......................12
4.5. Rear Derailleur Hanger Adjustment ..................13
 4.6.Mechanicalgroupsetspecication ............... 14-16
 4.7.Electronic(Di2)groupsetspecication ........... 17-21
 4.8.Electronic(Wireless)groupsetspecication ..........22
For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,
particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque
wrench to make sure every bolt is at the right torque setting to prevent damage.
NITROGEN DISC 286A: Table of Contents
2
My Nitrogen Disc
Date of purchase:
Retailler:
Size:
Serial Number:

Tools needed for assembly
1: Bearing Cup Press (Park Tool HHP-2)
2: Allen Key Set
3: Grease
4: Utility Pick Set (Park Tool Item #UP-SET)
5: Clean Rags
6: Derailleur Hanger Alignment Gauge (Park Tool Item #DAG-2 or #DAG-2.2)
7: Cables and Housing Cutter
8: Carbon Paste
9: Loctite #242
10: Torque Wrench
First Aid Kit: Essential parts to always have on hand
IN CASE OF EMERGENCY…THIS MIGHT SAVE YOUR RIDE!
1: Spare rear derailleur hanger assembly
2: Seat post collar
NITROGEN DISC 286A: 1. Tools Needed and First Aid Kit
80802 80832
(Direct mount option if utilized)
3

Parts installed on the frame Description Screw Tork Detail
type Nm
Front derailleur hanger Screw (2) 5mm 4Nm Loctite
Rear derailleur hanger Screw 4mm 2Nm Loctite
Bottle cage Screw (4) 5mm 3Nm Grease
Bottom bracket cable guide Screw 5mm 1.5Nm Grease
IMPORTANT:
The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their torque
specications.
NITROGEN DISC 286A: 2. Frame Inspection
4
BEFORE ASSEMBLING YOUR NEW NITROGEN DISC, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:
1: Frameset parts checklist (see p.5)
2: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)
3: For reference, check serial number and write it on p.2
4: All the necessary bolts (refer to Frameset Parts, p.5)
5: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is
straight (p.13)

NITROGEN DISC 286A: 3. Frameset Parts, SKUs and descriptions
5
38757
38885 38260
38884
80802
38882
38724
38880 38888
FK.NIT_D.286A
SP.NIT_D.286A
38881 38879 39009
80375,
80478
80374,
80477
running change
Images are for reference only. Proportions are not accurate.
Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.
*For more info please consult notice on Seatpost clamp dated 2016-06-09
8099981000
80832
80812 80813
80551

NITROGEN DISC 286A 3. Frameset Parts, SKUs and descriptions
6
No. Name Assembled on A18 SKU# Qty
Parts already assembled
Parts
1 Nitrogen Disc Frame - - 1
2 Nitrogen Disc Fork - FK.NIT_D.286A 1
3 Nitrogen Disc Seat Post Assembly - SP.NIT_D.286A 1
4 Head Tube Brake Cable Stopper Frame 38878 1
5 Top Tube Cable Stopper Frame 38879 1
10 BB Cover (incl. screw) Frame 38260 1
11 Seat Clamp Base (incl. screw) Frame 80375, 80478 1
12 Seat Clamp Wedge (incl. screw) Frame 80374, 80477 1
13 Di2 Cable Grommet Frame 38888 1
14 Mechanical Cable Grommet (Top Tube) Frame 38880 1
15 Di2 Grommet (Top Tube) Frame 38881 1
16 3D Headset Assembly Fork 38724 1
19 Chainstay Cable Grommet Frame 39009 1 Set
20 Internal Di2 Battery Support Seat Post 38757 1 Set
21 8mm Wrench for Seat Clamp - 38543 1
22 HT Rear Brake Grommet Di2 Frame 81000 1
23 HT Rear Brake Grommet Frame 80999 1
24 Direct Mount Rear Derailleur Hanger Frame 80832 1
25 DT Swiss RWS Thru-axle FRONT 12 x 119mm Fork 80812 1
26 DT Swiss RWS Thru-axle REAR 12 x 161mm with handle Frame 80813 1
27 TT Di2 Plug Frame 80026 1
28 Oblong Cable Guide Frame 80551 2
29 Rear derailleur plug for eTap Frame 80825 1
30 Round plug Frame 80554 1
31 TT grommet (Di2) Frame 38881 1
8 Rear Derailleur Hanger (incl. dropout, screw) Frame 80802 1
6 Front Derailleur Hanger (incl. screws) Frame 38882 1
9 BB Cable Guide (incl. screw) Frame 38885 1
7 Bottle Cage Screws Frame 38884 4
*Except for the frame itself, which is not sold as a spare part, all parts can be ordered by referring to their respective SKU number.

Install the 3D headset (16.3 & 16.4)
accordingtotheAEROPresstassembly
guide.Youcanchoosefrom3dierent
heights: 25mm, 15mm or 0mm.
7
NITROGEN DISC 286A: 4.1. Headset Installation
16.3 & 16.4
GREASE
GREASE
GREASE
GREASE

8
NITROGEN DISC 286A: 4.1. Headset Installation
25mm
15mm
0mm
setup
setup
setup
5
3
4
1
1
1
5
3
4
5
3
4
5
6
7
2
6
2
7
8
6
5 5
Compressor
Top cap (including O-ring & seal)
Micro spacers
Compression ring
Bearing
3D bearing holder
Plastic sleeve (no need for 0mm setup)
Top cap for 0mm setup
1
2
3
4
5
6
7
8
head tube
(bike)
head tube
(bike)
head tube
(bike)
To remove the 3D bearing holder, insert the Park Tool
RT-1 and then tap it carefully until the spacer comes out.
1
STEP
Inspect the bike’s head tube for any sharp edges and
apply a small amount of grease.
2
STEP
For the 25mm and 15mm setups, lightly grease the
bottom section of the 3D bearing holder (6) and insert
the plastic sleeve (7).
3
STEP
Position the headset inside the head tube. Place
the top 3D assembly with the headset bearing inside
(this will prevent the sleeve from getting damaged).
Add the compression ring on top of the bearing, then
add the press t 3D system tool and softly press down
the assembly until it bottoms out using a Bearing Cup
Press (Park Tool HHP-2). Then, insert the bottom
bearing (5), compression ring (4) micro spacers (3) and
top cap (2), slide the fork and stem and measure the
steerer length needed.
For the 0mm setup , do not use the plastic sleeve.
Install the 3D bearing holder (6) with grease applied
directly inside the frame.
4
STEP
First, you must assess which setup suits your needs:
25mm, 15mm or 0mm.

9
NITROGEN DISC 286A: 4.1. Headset Installation
Compressor
Top cap (including O-ring and seal)
Micro spacers
Compression ring
Bearing
3D bearing holder
Plastic sleeve (no need for 0mm setup)
Top cap for 0mm setup
1
2
3
4
4
5
5
6
6
7
7
8
Press Fit 3D system tool 1 1/4”
Bearing Cup Press (Park Tool HHP-2)
IMPORTANT: Use the Press Fit 3D system tool 1 1/2” with
the Bearing Cup Press (ParkTool HHP-2) to avoid any
damage on the bike frame.

NITROGEN DISC 286A: 4.2. Seat Post Installation
10
1. Place the seat post collar inside the
frame.
2. Insert the seatpost (3) on which
somecarbonberassemblygelhas
been applied.
3. Position the seatpost to the desired
height.
4. Apply a drop of blue Threadlocker
(n. 242) on the bolt’s thread
5. Tighten the set screw at max. 5.5Nm
while leaving a space between the two
parts allowing them to slide.
GREASE
GREASE
THREADLOCKER
BLUE (n. 242)
LOCTITE
GREASE
CARBON FIBER
ASSEMBLY
COMPOSITE
5.5 Nm
1Nm
11
RUNNING CHANGE
11
12