ARGON18 E-119 TRI+ User manual

travelguide

2E-119TRI+DISC: travel guide
Tableofcontents
TOOLS NEEDED & EMERGENCY REPAIR KIT 
DISASSEMBLY AND PACKING -
 Remove the wheels 
 Remove the seatpost collar and seatpost 
 Remove the bento box 
 Remove the stem cap 
 Remove the bottle cage mount 
 Loosen the bridge 
 Remove the bridge 
 Remove the handlebar 
 Pack your bike 
REASSEMBLY -
 Install the handlebars 
 Install the bridge 
 Tighten the bridge 
 Install the bottle cage mount 
 Install the stem cap 
 Install the bento box 
 Install the wheels 
 Insert the seatpost and seatpost collar 
CONTACT 
My E-119 Tri+ Disc
Size:
Serial number:
Seatpost height:
Bridge angle:

3
E-119TRI+DISC: travel guide
ToolsNeeded&emergencyrepairKit Removethewheels
1. Remove the front wheel using a 6mm allen key.
2. Repeat for rear wheel.
3. If the travel bag or case doesn’t secure both axles,
install an axle spacer to avoid frame compression.
4. Install brake pad spacer in both calipers to avoid
brake pad locking closed during travel.
5. Depending on your travel case, the rear derailleur
may also need to be removed.
Brake pad
spacer
Disassemblyandpacking
IMPORTANT:
EMERGENCY REPAIR KIT. Essential parts to always have on hand
IN CASE OF EMERGENCY…THIS MIGHT SAVE YOUR RIDE!
IMPORTANT:
Indicates special precautions and important steps that must
be taken to avoid damage and/or injury.
Apply carbon paste
on the indicated
surfaces.
Apply grease on the
indicated surfaces.
Apply threadlocker
on the indicated
surfaces.
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
Torque Value
Allen key size
81504 80802 80832
SEAT POST CLAMP
SET OF ALLEN KEYS
SET OF TORX KEYS
CARBON PASTE
& GREASE
TORQUE WRENCH
CLEAN RAG
ISOPROPYL ALCOHOL
MEDIUM-STRENGTH
THREADLOCKER
Tektro F10RS
Semi-Metallic
SPARE BRAKE PADSPARE REAR DERAILLEUR HANGER
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
3
6
2.5
4Nm
8
3
1.5
HT

4E-119TRI+DISC: travel guide
1. Mark or record the height of the seatpost.
2. Unscrew the M8 x 10mm set screw in place.
3. Remove the wedge by lifting with the Allen key before removing the seatpost.
4. Remove the seatpost.
5. Unplug the battery if using Di2.
6. Store the wedge and seatpost in your travel bag.
Removetheseatpostcollarandseatpost Removethebentobox
M4 x 16mm
Disassemblyandpacking
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
3
2.5 3
36
2.5
4Nm
8
3
1.5
HT
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT
1. Remove the rear M4 x 16mm screw.
2. Loosen both M4 x 16mm front screws.
3. Lift the rear of the bento box and slide it toward the rear
of the bike to remove the unit.
4. Place the bento box and screws in the travel bag.

5
Démontageetempaquetage
E-119TRI+DISC: travel guide
REGULAR POSITION
FORWARD POSITION
WITHOUT WATER BOTTLE MOUNT
Removethestemcap
1. Remove both M3 x 6mm stem cap screws.
2. Lift the rear of the stem cap and pull backward until the front edges are clear
of the first spacer.
3. Remove the cap and place the stem cap and screws in your travel bag.
Removethebottlecagemount
1. Unscrew the water bottle cage and the mount.
2. Remove the bridge plug if the mount is not being used.
M5 x 12mm
M5 x 14mm
M5 x 8mm
M5 x 14mm
M5 x 8mm
M5 x 12mm
M3 x 6mm
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
3
6
2.5
4Nm
8
3
1.5
HT
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
3
6
2.5
4Nm
8
3
1.5
HT

6E-119TRI+DISC: travel guide
M6 x 18mm
1. Record your bridge angle. __________________ . Angles are laser etched on
the swivel spacer and beam.
2. Loosen the two M6 x 18mm swivel screws (only one turn) just
to allow angle movement.
3. Unplug the shifter from the junction box or Blipbox, if you have
an electronic build.
Loosenthebridge Removethebridge
1. Tilt the bridge backward to access the front spacer M6 screw.
2. Remove the front spacer screw.
3. Tilt the bridge forward to access the rear spacer M6 screw.
4. Remove the rear spacer screw.
5. Pack the bridge, spacers and screws in the travel bag.
M6
M6
Disassemblyandpacking
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5
5
2.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5
5
2.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5
5
2.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT

7
Démontageetempaquetage
M6 x 16 mm
E-119TRI+DISC: travel guide
Removethehandlebar
1. Remove both M6 x 16mm screws from the first spacer.
2. Remove the first spacer.
3. Pack the first spacer and screws in the travel bag.
Packyourbike
1. Place and secure the handlebar on the non-drive side of the frame.
2. Pack the bike, wheels and small parts in the travel bag according to
bag instructions.
3. Make sure everything is secured (chain, handlebar, bridge assembly, etc.)
to avoid paint damage.
IMPORTANT:
Use a spacer in axles to avoid compression damage
during travel.
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT

8E-119TRI+DISC: travel guide
Installthebridge
1. Apply grease to the threads of the two spacer screws
(SKU: 81532 to 81541).
2. Tilt the bridge forward to install the rear spacer M6 screw.
3. Install and tighten the rear M6 spacer screw to 9 Nm.
4. Tilt the bridge backward to install the front spacer M6 screw.
5. Install and tighten the front M6 spacer screw to 9 Nm.
6. For electronic assembly, run the extension cable from the junction box
through the channel in the spacers and swivel.
7. Connect both extensions cables to the JC-41 junction box or Blipbox
if you have an electronic build.
Installthehandlebars
1. Unpack the bike from the travel bag.
2. Install the handlebar on the fork.
3. Install the first spacer over the handlebar.
4. Apply grease to the threads of both M6 x 16mm
button head screws (SKU: 81545).
5. Tighten both M6 x 16mm button head screws to 6 Nm.
reassembly
M6 x 16mm
M6
M6
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5
5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5
5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm

9
E-119TRI+DISC: travel guide
Installthebottlecagemount
M6 x 18mm
1. Adjust the bridge angle as noted while disassembling.
2. Tighten both M6 x 30mm screws to 9 Nm.
Tightenthebridge
1. Install the water bottle mount on the bridge, using the grey M5 x 12mm screw.
Tighten it to 2 Nm.
2. Screw the water bottle cage onto the mount at the desired position using the
red screws. Tighten both screws to 2 Nm.
3. Insert the bridge plug if the mount is not being used.
REGULAR POSITION
FORWARD POSITION
WITHOUT WATER BOTTLE MOUNT
M5 x 14mm
M5 x 8mm
M5 x 12mm
M5 x 12mm
M5 x 14mm
M5 x 8mm
reassembly
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5
5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm

10 E-119TRI+DISC: travel guide
1. Slide the bento box onto the frame hole on the top tube.
Make sure the frame is between the bento box and the clamp.
2. Apply threadlocker to the threads of the screws.
3. Hand-tighten the three M4 x 16mm screws.
1. Insert the front edges into the first spacer grooves.
2. Push the stem cap down until the holes are aligned with the threads
on the fork.
3. Install and hand-tighten both M3 x 6mm screws.
4. If using eTap: Push the blipbox into the stem cap until it clicks.
M3 x 6mm
eTap Only
M4 x 16mm
InstallthebentoboxInstallthestemcap
reassembly
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
3
2.5
HT
HT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
4
2.5
4
4
25
2 3
4
8
2.5
3
T25
T25
4
10
2.5 52.5
2.5
1.5
32.5 3
36
2.5
4Nm
8
3
1.5
HT

11
E-119TRI+DISC: travel guide
17. Insert the seatpost and seatpost collar16. Install the wheels
1. Remove both axle protectors.
2. Remove both brake pad spacers.
3. Apply grease to the axle threads.
4. Place the rear wheel in the frame.
5. Thread the thru-axle through the wheel
and tighten it to 10 Nm.
6. Repeat for front wheel.
7. Apply pressure on both brake levers.
8. Make sure wheels are turning freely
and the discs don’t rub. If they do,
adjust the caliper position.
reassembly
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
4
6 Nm
2.5
1 Nm
4
5.5 Nm
4
7 Nm
2
HT-1/4
5
12 Nm
2
2 Nm
3
3 Nm
4
3 Nm
8
35 Nm
2.5
HT
3
HT
40 Nm 4 Nm
T25
T25
4
3 Nm
10
HT
2.5 5
9 Nm
2.5
HT-2
2.5
HT-5
2.5
2 Nm
32.5
HTHT
3
4 Nm
3
2 Nm
6
10 Nm
2.5
HT
4Nm
6 Nm
8
3
5 Nm
1. Plug in the Di2 battery if using a Di2 build.
2. Set the seatpost to the desired height (where you marked your height
while disassembling).
3. Tighten the M8 x 10mm set screw on the seat post clamp to 5.5 Nm.
IMPORTANT:
Refer to p.16 of the assembly guide for seat post MIN and
MAX insertion values.

argon18.com