Argos Home 875/0352 User manual

Multi-Purpose Tidy Rail
Dimensions
Width - 106cm
Depth - 43.5cm
Height - 166cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions - Please keep for future reference
875/0352
Issue 1 - 28/05/10

1
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the unit as close to its
final position (in the same room)
as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
• Dispose of all packaging
carefully and responsibly.
Safety and Care Advice
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit. 
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre. 
Care and maintenance
Important - Please read these instructions fully before starting assembly
as this could damage the unit.
Only use hand screwdrivers.

2
End section x 1
1
Upright section x 1
2
End section x 1
3
Base x 1
4
Crossbar x 1 (73cm)
5
Shelf support x 6 (28cm)
6
Shelf x 3
7
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Components - Fittings
Please check you have all the fittings listed below
38mm Screw x 20 Spacer x 2 Threaded cap x 4
Spanner x 1
Allen key x 1
Castor x 4
A
D
B
EF
C

a:
b:
Assembly Instructions
Step 1
Note: It would be useful
to ask someone to help
you at this stage.
2
3
2
1
2
2
1
A
A
A
E
A
A
A
C
A
F
A
D
2
6
2
6
1
3
A
CA
F
A
D
1
6
2
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
E
a: Insert Threaded end
cap into End sections
& . Ensure screw
of End cap correctly
aligns with hole for
castor in End section
& , then screw
Castor into position
and tighten firmly with
Spanner .
b: Secure Shelf supports
to End section
using Screws and
tighten with Allen key .
And then fit Upright
support to Shelf
supports using
Screws .
3
A
C
12
3
A
D

b:
a:
Assembly Instructions
Step 2
2
1
2
5
4
2
3
3
5
4
E
Finishing the Unit
a: Attach Base to
End section using
Screws , and then
attach to Upright
support as shown at
the figure.
A
A
A
A
A
A
A
A
5
32
4
b: Fix Crossbar to
Upright support and
End section using
Screws .Then using
Screws attach End
section to Base
and Crossbar .
4
4
1
A
A
B
E

a:
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Step 3
Assembly is complete.
7
6
6
7
Finishing the Unit
a: Stand product up.
Position Shelf over
two Shelf support
and push down gently
until shelf clips into
place on both sides.
7