Argos Home Maddison Bunk 805/8906 User manual

Maddison Bunk
Important - Please read these instructions fully before starting assembly
Dimensions
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Issue 1 -12/10/17
805/8906
Assembly Instructions - Please keep for future reference
Length - 198cm
Width - 97cm
Height - 165cm
798/6110

Important - Please read these instructions fully before starting assembly
Mattress height safety notice
Important
1) Please note the maximum mattress height is indicated on the corner post inside the opening at the
top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.
3) Maximum thickness of the mattress is 16cm:The top of the mattress shall not come above the line
marked on the bed.
4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are
loose.
5) Recommended size of the mattress for the both bunks is 90×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) Warning: High beds and the upper bed of bunk beds are not suitable for children under six years
due to the risk of injury from falls.
8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or
hung on a bunk bed.
Warning
1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance
between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2012+A1:2015.
1
Safety and Care Advice
!
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Place the product on flat and
steady surface during use.
• Keep these instructions for
future use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing
points be fully tightened.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Safety: To avoid any risk of
suffocation to animals or
children dispose of the plastic
bags immediately.
• Cleaning: As with all surfaces
clean with a damp cloth and
mild detergent, do not use
bleach or abrasive products.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Please check you have all the parts listed below
1
Components - Parts
2
Upper corner post x 4 (3.8 x 103.5cm)
8Ladder (109 x 35.7cm)
3End panel (Upper) x 2 (97 x 39.8cm)
4End panel (Lower) x 2 (25 x 88.5cm)
7Front guard rail (95.5 x 42cm)
5Rear guard rail (95.5 x 42cm)
10 Slats x 44 (□2 x 1 x 95cm)
6Guard rail x 2 (97 x 42cm)
9End Slats x 4 (□2 x 1 x 95cm)
2Lower corner post x 4 (3.8 x 66.5cm)
12 External bracket x 2 (4.3 x 2.3 x 12cm) 11 Internal bracket x 4 (3.7 x 1.7 x 12cm)
Lower side rail (95.5 x 6.8cm)-Extra hole for ladder
13
Lower side rail × 3 (95.5 x 6.8cm)
14 15 Support foot x 2 (26 x 2.3 x 12cm)

Please check you have all the fittings listed below
Components - Fittings
3
If you have damaged or missing components,
call the Customer Helpline: 0345 6400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
ABC
M6x15mm Allen screw x 4
D E
M6x40mm Allen screw x 8
F
Curved washer-large x 16
G H J
Nut x 28
K M
Plastic plug x 2
A
Curved washer-small x 27
Plastic washer x 16
M6x60mm Allen screw x 11
M8x60mm Allen screw x 8
M6x10mm Allen screw x 102
L
Plastic cap x 4
M6x35mm Allen screw x 8
R
M6x42mm Allen screw x 8
N
M6x25mm Allen screw x 4
PQ
Small allen key x 2 Large allen key x 1
S
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2 3 4 5 6
Ruler/tape
measure
Ruler - Use this ruler to help correctly identify the screws
Tools required
Foot x 4

Assembly Instructions
4
Assembling side frames
Lay one corner post，an
upper end panel and a
lower end panel flat on
the floor as shown.
Note: The brackets on
end panel must be at
the top.
Insert upper end panel
into the large holes in
the corner post.
Secure using fixings
and .
Note: Do not fully
tighten screws .
Assemble lower end panel
to the corner post
using fixings and .
Note: Do not fully
tighten screws .
Align another corner post
onto the ends of the upper
and lower end panels.
Secure using fixings ,
and as shown.
Repeat for the other side
frame.
4
3
3
A
A
4
BC
B
C
B
2
4
Top
Bottom
3
Step 1
C
L
1
2
Step 2
AB
C
Preparing corner posts
Join upper corner posts
and lower corner
posts together and
secure using fixings
and .
1
2
C
L
2
C
B
2
3
1
1
C
A
4
K
J
K
J
2
CJK

Step 3
L
6
5
Assembly Instructions
5
P
P
J
J
J
J
P
P
L
6
7
J
J
P
P
5
6
11
11
L
6
11
Assembling upper
guard rail (front)
To assemble the front
guard rail, repeat the
assembly from step 3
above, using front guard
rail and remaining
guard rail .
11
6
L
a:
a:
Rear
Front
Step 4
Assembling upper
guard rail (rear)
a: To assemble the rear
guard rail, locate internal
bracket inside guard
rail as shown.
Secure using screw .
b:
b: Locate rear guard rail
over the end of the
internal bracket in guard
rail and secure using
fixings and .
6
5
JP
7
6

Assembly Instructions
6
L
11
14
14
b:
Step 5
Assembling lower side
rails
a: Locate internal bracket
inside lower side rail
, and secure using
screw .
Slide lower side rail
over the internal bracket
and secure using screw .
Note: Lower side rail
has an extra hole for the
ladder fixing, This will
become the front side rail !
L
11
14
13
a:
L
11
13
14 L
14
b: Repeat a: to assemble
two lower side rails
together as shown.
This will become the rear
side rail !
14
11
14
13
L
L
13
Note: Hole for
ladder fixing.
Rear
Front

Assembly Instructions
Assembling rear guard
and side rail
Two people are needed
here.
With help, stand both
side frames upright.
a: Assemble the rear
guard rail assembly
and in between the
side frames as shown.
Note: Do not fully tighten
any screws during the
assembly.
Secure at the top using
fixings and as
shown.
Secure at the bottom
using fixings ,
and as shown.
Note: Plastic washers
are located in between
the rear guard and the
side frames.
5
BC
E F G H
J
F
7
6
Step 6
BC
b: Assemble the lower
side rail assembly at
the rear of the side frames
using fixings ,
and as shown.
Note: Ensure the 24 holes
in side rail are on the
top edge.
With help, fit feet to the
corner posts .
Note: Ensure the feet
extend outwards as
shown.
Warning:
The bunk bed
is heavy. Lift
with care.
Q
14
E F G H
J
14
JE
G
F
Q
2
Feet to extend outwards.
b: 2G
F
F
E
E
J
H
14
Q
Q
b:
Holes on top
6
5
a:
1
BC
HEF
G
6
JEF
a:
1
1
1
1
2
2
2
2
14 14
G
F
JE
HE

Assembly Instructions
Step 7
EH
F
G
J
B
C
1
6
E
F
8
H
E
J
F
G
2
F
E
14
Alternative assembly
b:
a:
Assembling front
guard
At this stage, choose if
you want the ladder on
the right hand side or left
hand side.
a: According to which
side you want the ladder,
assemble the front guard
assembly and in
between the side frames
as shown.
Secure at the top using
fixings and .
Secure at the bottom
using fixngs , , ,
and .
b: Assemble the lower
side rail assembly and
in between the side
frames at the front of the
bed using fixings ,
and .
Note: Ensure the ladder
fixing holes in the front of
side rail are on the
same side as the ladder
access gap in front guard
.
Note: Ensure all fixings
are left loose.
E F G
HJ
13
E F
HJ
13
7
14
G
67
BC
H
E
F
E
F
G
J
b:
Note: Hole
Note: Hole
L
A
D
D
E
R
13
14
7
6
J
EH
F
G
E
F
a:
B
C
D
2
D
Note: Hole
Note: Hole
L
A
D
D
E
R
c: Insert end caps into
the top of the corner
posts.
D
c:

Assembly Instructions
9
Step 8
Assembling end slats
Fit end slats in the
very last fixing holes at
each end of the bed
(top and bottom bunks).
Note: The arrow labels
on
slats must point
outside.
Note: Slats have been
labelled for easier
identification.
9
9
9
9
Slats at
each end
93
Arrow label to
point outside
9
9
9
L
9
L