Argos Home Jorvic 620/5555 User manual

MADE IN
BRITAIN
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0330 016 1114
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
More help is available throughout this
booklet by scanning in the QR codes
or typing in the links
WARNING!
In order to prevent overturning, this product must be
used with the 2 wall attachment devices provided
Assembly Instructions - Important: Retain these instructions
for future reference
Dimensions
Width - 90.5cm
Depth - 24cm
Height - 150.5cm
Jorvic - CD Unit
Issue 4 - 23/01/20
620/5555

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
1
Care and maintenance
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Regularly check all fastenings
to ensure that they are properly
tightened.
• Warning: This unit weighs
approximately 28kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions
- otherwise a safety risk can
occur if incorrectly installed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall
using the 2 overbalance
protector kits supplied.
• Dispose of all packaging
carefully and responsibly.
• Do not use this item if any
components are missing or
damaged.

Components - Panels
Please check you have all the panels listed below
2
1Left Side (DF-00021890)
(147.5 x 16.7cm)
Middle Shelf (DF-00021894)
(87 x 16.5cm)
Top Upright (DF-00021895)
(83.6 x 16.3cm) x 2
2Right Side (DF-00021891)
(147.5 x 16.7cm)
6
7
Top (DF-00021892)
(90.3 x 16.9cm)
Bottom Upright (DF-00021896)
(62.4 x 16.3cm) x 2
8Shelf (DF-00021897)
(28 x 16.1cm) x 15
Base (DF-00021893)
(90.3 x 23.9cm)
3
4
5
9Middle Back (X802)
(150 x 29.4cm)
10 Back (X1500-300)
(150 x 30cm) x 2

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
Tools required
3
Wooden dowel (F22) x 28
B C
D E
Large locking
cam nut (F900) x 6
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(only use when
drilling into walls)
Metal dowel (F901) x 6
A
Wooden dowel (F40) x 24
50mm Screw (F49) x 8
F
Allen Key (F36) x 1
HG
Nail (F51) x 32
IStrap Screw Washer x 2
Overbalance protector kit (F269) x 2
15mm Screw (F284) x 12

A
A
AA
AA
Assembly Instructions
4
Prepare the 2 top
uprights
Tap 2 short wooden
dowels into each of
the top uprights as
shown.
Note: The short wooden
dowels must not stick
out from the edge by
more than 10mm or they
may damage other
panels.
B
6
Join 3 shelves to a
top upright
Position 3 shelves
against a top upright
as shown.
Tap 6 long wooden
dowels through the
top upright and into
each of the shelves .
Step 1
Step 2
Fit the other top
upright
Fit the other top upright
. to the assembly.
Tap 6 long wooden
dowels through the
top upright and into
each of the shelves .
Step 3
x 2
B
B
Finished
front edge
Gently tap the large
dowels through the top
upright and into the shelf
until they ‘bottom out’.
A
A
Finished
front
edge
10mm
B
Finished
front
edge
Short wooden
dowels at the top
A
6
6
8
8
6
A
6
8
Finished
front
edge
Finished
front
edge
8
8
8
8
8
6
6
Finished
front
edge
Short wooden
dowels at the top
A
6
8
A
A
A
A

Assembly Instructions
5
Prepare the middle
shelf
Insert 4 large locking
cam nuts into the
middle shelf as
shown.
5
Fit the middle shelf
Position the middle shelf
. onto the assembly as
shown.
Tap 4 long wooden
dowels through the
middle shelf and into
the bottom of the 2 top
uprights .
Step 4
Step 5
Step 6
D
A
AA
A
5
5
A
5
6
6
Finished
front
edge
6
A
A
A
A
Join 2 shelves to a
bottom upright
Position 2 shelves
against a bottom upright
. .
Tap 4 long wooden
dowels through the
bottom upright and
into each of the shelves
. .
Note: Make sure that the
bottom uprights are the
right way around. The
8mm holes are in the top
edge and the 5.5mm
holes are in the bottom
edge.
8
A
7
8
Finished
front
edge
Finished
front
edge
8mm holes
5.5mm holes
Finished
front
edge
7
8
8
7
Finished
front edge
D
D
D
D
D
5

A
A
A
A
5
Assembly Instructions
6
Step 7
Fit the bottom upright
assembly
Push the 2 bottom
uprights onto the
middle shelf .
Step 8
Step 9
7
7
7
Finished
front
edge
Finished
front
edge
5
Finished
front
edge
8
8
7
Fit the other bottom
upright
Fit the other bottom
upright to the
assembly.
Tap 4 long wooden
dowels through the
bottom upright and
into each of the shelves
. .
7
A
7
Prepare the remaining
shelves
Tap 2 short wooden
dowels into each of
the remaining shelves
as shown.
x 10
B
B
Finished
front edge
8
B
8
8mm holes
5.5mm holes
5.5mm holes
5.5mm holes
8

Finished
front edge
Assembly Instructions
7
Step 10
Step 11
Prepare the left side
Screw 2 metal dowels
into the left side .
Note: Tighten metal
dowels up fully against
the panels.
Tap 2 short wooden
dowels into the left
side as shown.
Insert a large locking
cam nut into the left
side .
Fit the shelves
Push the shelves
onto the top uprights
and bottom uprights
as shown.
Note: Make sure that all
of the shelves have the
finished front edge
pointing upwards.
7
7
Finished
front edge
Finished
front edge
8
8
8
8
88
8
8
8
8
6
6
8
6
7
D
B
B
CC
1
C
C
1
B
1
D
1
8
6
7

Assembly Instructions
8
Step 12
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 2 large locking
cam nuts fitted to the
middle shelf .
Note: Turn the large
locking cam nuts as
far as they will go - more
than 1/2 a turn.
1
D
5
D
Finished
front edge
B
B
D
Finished
front edge
CC
Step 13
Prepare the right side
Screw 2 metal dowels
into the right side .
Tap 2 short wooden
dowels into the right
side as shown.
Insert a large locking
cam nut into the right
side .
C
2
2
2
B
D
2
5
1
C
D

Assembly Instructions
9
Step 14
Step 15
Fit the base
Fit the base to the
assembly with 8 screws
. and tighten them
using the allen key .
7
Fit the right side
Push the right side
onto the assembly.
Use a screwdriver to
tighten the 2 large locking
cam nuts fitted to the
middle shelf .
2
D
5
5
Finished
front edge
Step 16
Prepare the top
Screw 2 metal dowels
into the top .
Finished
front edge
C
C
E
E
E
E
FE
E
E
E
Finished
front edge
4
E
F
4
C3
3
2