Argos Walton 162/8405 User manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 89.5cm
Height - 74cm
Walton - Corner Desk
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/10/13
Important - Please read these instructions fully before starting assembly
ALR2915
162/8405

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 29kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Return Leg (D1417A)
(718 x 231mm)
Left Side (D1414A)
(718 x 570mm)
Right Side (D1415A)
(718 x 570mm)
Large Modesty (D1418A)
(944.5 x 239mm)
Small Modesty (D1419A)
(639.5 x 239mm)
Top (D1413A)
(1199 x 894mm)
2
4
6 7
3
Leg (D1416A)
(718 x 214mm)
5

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 8
C
D E
Large locking
nut (F900) x 8
F
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
see malibu fitment mk2 for large number of panels and fittings
Electric drill
(do not use for
fitting screws)
50mm Screw (F49) x 8 45mm Screw (F65) x 2 Allen Key (F36) x 1

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the top
Screw 8 metal dowels
into the top .
Note: Tighten the metal
dowels up fully against
the panels.
B
B
BB
B
B
B
B
B
B
1
1
Step 3
Prepare the return leg
Insert 2 large locking
nuts into the
return leg .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
C
C
C
Finished
front edge
C
Prepare the leg
Insert 2 large locking
nuts into the leg .
C
4
5
4
C5

Assembly Instructions
5
Fit the return leg
Push the return leg
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the return leg .
Step 4
Step 5
1
C
B
5
1
Finished
front edge
4
Fit the leg to the top
Push the leg onto the
top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the leg .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
1
C
5
C
4
1
C
4

Assembly Instructions
6
Step 6
Secure the leg to the
return leg
Secure the return leg
to the leg using 2
screws .
Note: Make sure that
the leg is straight and in
line with the return leg.
1
45
E
E
4
5
E
Step 7
Fit the small modesty
Push the small modesty
. against the leg
and secure it using 2
screws and the allen
key .
5
7
D
F
D
75
D
F

Assembly Instructions
7
Step 8
Fit the large modesty
Push the large modesty
. against the return leg
. and secure it using 2
screws and the allen
key .
6
4
D
F
6
4
DF
D
A
A
Step 9
C
10mm
A
Prepare the left side
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the
left side .
Step 10
C
A
2
C
2
2
Finished
front edge
A
A
C
C
Prepare the right side
Tap 2 wooden dowels
into the right side .
Insert 2 large locking
nuts into the
right side .
3
A
3
C
3
Finished
front edge

Assembly Instructions
8
Step 11
Fit the right side
Push the right side
onto the top .
Secure the right side to
the large modesty
using 2 screws and
allen key .
D
D
F
3
1
6
3
1
3
6
D
F
Secure the right side
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Step 12
C
3
3

Assembly Instructions
9
Step 13
Step 14
D
D
F
Fit the left side
Push the left side
onto the top .
Secure the left side to
the small modesty
using 2 screws and
allen key .
2
1
2
7
D
F
1
2
7
2
Secure the left side
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
C
2