Argos Brooklyn 8529198 User manual

Singlebed - Brooklyn
Dimensions
Length - 200,4cm
Depth - 100,2cm
Height - 84,4cm
Weight - 26,6kg
Issue 4 - 25/08/22
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
8529198
IMPORTANT! KEEP FOR FUTURE
REFERENCE

1
Safety and Care AdviceSafety and Care Advice
Important – Please read these instructions fully before starting assembly
80-23101-65 Singlebed
IMPORTANT! KEEP FOR FUTURE REFERENCE
PLEASE DISPOSE OF PACKAGING MATERIAL.
PLASTIC BAGS CAN BE DANGEROUS TO YOUNG CHILDREN
WARNING! Not suitable for children under 4 years.
WARNING! Do not place this child’s bed near heat sources, windows and other furniture.
WARNING! Do not use this child’s bed if any of the parts are broken, torn or missing.
WARNING! Once assembled, this bed must not be disassembled. Screws must not be removed once inserted.
This child’s bed is to be used with a 1900mm x 900mm ma ress.
Suitable for over 4 years old to adults.
All assembly Įxings should be checked periodically and re- ghtened where necessary.
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not
be placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords, and should be
placed either ght to any wall or have a gap of 300mm between the wall and the side of the bed.
Any addi onal or replacement parts should only be obtained from the manufacturer or distributor.
This product complies to standard BS8509: 2008+A1:2011
CARE AND MAINTENANCE
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.
Always place the side of the bed with the safety rail against a wall.

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
2

Endrail x2
(86,5x5,5x5,5cm)
Endrail x3
(86,5x8,9x2,0cm)
Filling x2
(86,5x29,8x0,8cm)
Bedside x2
(186.7x8.9x2.0cm)
7 8
10
9
Leg x1 (82x5,5x5,5cm)
3
Components - Parts
Please check you have all the parts listed below
Leg x1 (66,7x5,5x5,5cm)
1
Leg x1 (82x5,5x5,5cm)
4
No. 12-05508201-65
Leg x1 (66,7x5,5x5,5cm)
2
No. 12-05506673-65
Top rail x2
(100,2x8,2x2,4cm)
6
No. 12-02410021-65
No. 12-05508651-65 No. 12-020086510-65 No. 4301-0808653-65
No. 1305-186710-65
If you have damaged or missing components,
call the Customer Helpline:
0045 7668 8055
3
No. 12-05506674-65
No. 12-05508202-65
Slat x15 (89,7x6,5x1,47cm)
11 No. 12-01508971

Components - Fittings
Please check you have all the fittings listed below
M6x100mm Connecting bolt x4
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
M6 ø10x14mm Barrel nut x4
B
E
10x50mm Dowel x18 8x50mm Dowel x4 5x40mm Dowel x2
D
Phillips
screwdriver
(medium)
Small
hammer
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
G
F
H
4,0x70mm Chipboard screw x8 6,3x105mm Assembly screw x8
4
No. 3930-10050
No. 3922-06014
No. 3913-06100
No. 4033-004
No. 3930-08050 No. 3930-05040
No. 3909-631051
No. 3901-40070
4.0x30mm Chipboard screw x30
i
No. 3901-40030

Insert the dowels Dinto
the holes in bedsides 10
and endrail 8and 7.
Insert Ø8 dowels Einto
the holes in endrail 7.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Attach endrails 7to top
rails 6using screws G.
Don’t overtighten.
Attach leg 2to endrail
7using the inserted
dowel only.
Attach endrail 8and
filling 9to leg 2using
the inserted dowel only.
Assembly Instructions
Step 1
Step 2
Step 3
8
2
9
7
7
6
G
G
G
G
10
8
7
D
D
D
E
D
D
D
E
Ø10
Ø8
5
G
E
D

8
2
1
7
H
H
H
H
Attach leg 1to endrails
7and 8.
Insert assembly screws
Hand fasten with
the allen key. Don’t
overtighten.
Insert Ø5 dowel Finto
the leg 4. Attach leg 4
to endrail 7using the
inserted dowels only.
Attach endrails 8and
filling 9to leg 4using
the inserted dowels only.
Step 5
Assembly Instructions
Step 4
8
4
4
9
7
F
Ø5
F
6
H

Assembly Instructions
Insert Ø5 dowel Finto
the leg 3as in the
previous step.
Attach endrail 8to
leg 4, at the same
time should leg 3be
attached to the two
endrails 8and 7using
the inserted dowels only.
Insert assembly screws
Hand fasten with
the allen key. Don’t
overtighten.
Attach bedside 10 to
the bed by placing the
dowels into the holes in
legs 2and 4.
Push 2 barrel nuts B
into the small holes
in bedside 10 . Push
1 connecting bolt A
through legs 2and 4
to meet the barrel nuts B
and fasten with the allen
key.
Step 6
Step 7
4
2
10
B
B
A
A
A
B
7
4
3 8
8
7
H
H
H
H
H

8
Assembly Instructions
Attach the second
bedside 10 to the bed by
placing the dowels into
the holes in legs 1and
3as in the previous
step.
Push 2 barrel nuts B
into the small holes
in bedside 10 . Push
1 connecting bolt A
through legs 1and 3
to meet the barrel nuts B
and fasten with the allen
key.
Place two slats 11 in the
ends of the bed, against
the legs. Fasten with four
chipboard screws i.
Place one slat 11 in the
middle of the bed. Follow
the measurements.
Push the bedsides 10
together whilst attaching
middle slat 11 to the
bed with two chipboard
screws i.
Step 8
Step 9
1
3
10
B
B
A
A
A
B
836 mm 836 mm
i
i
i
i
i
i
1111 11
10
10
i

Ref.no. 44-02047-65 D Stand: 250822 Page 10 (80-23101-65)
9
If you need help or have damaged or missing parts,
call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk
Assembly Instructions
Position the remaining
twelve slats 11 in the
bed with an approximate
distance of 63-64 mm
mm between each.
Fasten each slat with two
screws i.
Assembly is complete.
Step 10
i
i i
ii
i
ii
i
ii
i i
ii i i
i i
i
i i
i
i
63-64 mm
11 1111 1111 1111 1111 1111 11
i