Argos Darcy 424/5366 User manual

Dimensions
Width - 120 cm
Depth - 50 cm
Height - 91.6 cm
Darcy - 1 Door 2 Drawers Sideboard
424/5366
Important - Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400 800
Issue 1 -03/06/2015 1

!Safety and Care Advice
Important - Please read these instructions fully before starting assemb ly
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately 57 kgs.
Please lift with care.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly .Keep this page with
these instructions for future
reference.
2
• Check you have all the
components and tools listed on
pages 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels during assembly,
this could cause damage.
• Assemble the unit as close
to its final position (in the same
room) as possible.

Please check you have all the panels listed below
3
1
3
4
2
Right side
(82.5 x 49.8cm)
Left side
(82.5 x 49.8cm)
Top
(120 x 50.0cm)
Bottom
(120 x 50cm)
5
Vertical
partition top
(44.9 x 47.8cm)
8
Horizontal partition
(116.3 x 47.8cm)
6
Vertical
partition right
(44.9 x 47.8cm)
7
Vertical
partition
bottom
(35.8 x 44.2cm)
9
Front support
(86.3 x 8cm)
10
Flap
(115.7 x 35.2cm)
11
Drawer front x 2
(85.7 x 20.6cm)
12
Drawer back x 2
(80.7 x 12cm)
13
Drawer left side x 2
(40 x 12cm)
14
Drawer right side x 2
(40 x 12cm)
15
Drawer base x 2
(83.8 x 40,5cm)
18
Long plinth x 2
(109.6 x 5cm)
19
Short plinth x 2
(39,4 x 5cm)
16
17
Rear top (117.6 x 46.5cm)
Rear bottom (117.6 x 37.3cm)
Component - Panels If you have damaged or missing components
call the Customer Helpline: 0845 6400 800

Components - Fittings
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
4
I
(7x50) Hexagon bolt x 14
Wooden dowel x 70 (8x35) Hinge plate x 2
4x13mm Screw x 4 5x13mm Screw x 12
Cap x 20
Cap bolt x 14
Metal dowel x 20
Handle x4
Locking nut x20
( 15x13)
Door hinge x 2
CC
F
A C
D E
H
B
G
J
3x16mm Screw x 31
P
3,5x16mm Screw x 18
Q
Stabilizer x 14
U
K
3.5x27mm Screw x 8
HM
3x20mm Screw x 12
N
Allen key x 1
O
Feet x 4
R
Flap stay x 2
S
Bumper x 1
V
Runner x 2
W
Runner x 2
X
Mounting bracket x 6
Y
Height adjuster x 1
Z
4x16mm Screw x 2
L
Wall bracket x 2
T
Washer x 5
U1

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
5 & 8mm Suitable drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
Tools required
Assembly Instructions
Step 1Step 1
Insert locking nuts
into the left side panel
.
Insert wooden dowels
into the left side panel
.
Screw metal dowels .
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
A
F
a:
H
F
A
H
E
W
W
W
b: fixing runners
Position runners 38mm
from front edge
of the left side panel .
Fix runners with screws .
Mark the top left with a
punch. Screw into the
hole.
Attach flap stay using
screws .
b:
P
1
1
1
1
1
5
A
A
A
A
A
A
H
H
H
F
F
F
S
QQ
Q
Q
S
S
W
P
E E
38
E
Punch
a: Inserting dowels
and locking nuts

Assembly Instructions
Step 1Step 2
a:
b:
6
Insert locking nuts
into the right side panel
.
Insert wooden dowels
into the right side panel
.
Screw metal dowels .
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
A
F
H
2
2
2
F
A
H
A
A
A
A
A
A
H
H
F
F
b
flap stay usingAttach
screws .
Q
Q
Q
Q
S
S
S
2
a: Inserting dowels
and locking nuts

Assembly Instructions
Step 1Step 2Step 1Step 3
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
F
F
F
F
F
F
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
F
A
7
H
H
5
6
7
Insert locking nuts
into the vertical partitions
.
Insert wooden dowels
into the vertical partitions
.
Screw metal dowels .
A
F
H
5
5
6
6
7
7
Finished
front edge
a: Inserting dowels
and locking nuts

Assembly Instructions
Step 1
Step 1
Step 2
Step 2
Step 1
Step 1
Step 4
Step 5
Finished
front edge
8
8
8
E
W
W
W
Fixing runners
Position runners 40mm
from front edge
of the vertical partition
top .
Fix runners with screws .
Mark the top right with a
punch. Screw into the
hole.
5
5
P
A
F
H
A
A
A
A
A
F
F
H
H
H
A
A
F
F
F
Insert locking nuts
into the horizontal partition
.
Insert wooden dowels
into the horizontal partition
.
Screw metal dowels .
8
W
P
EE
38
E

Assembly Instructions
Step 6
Screw metal dowels
into the top .
Attach “hinge plates"
into the bottom .
3
4
Step 7
3
4
H
H
B
B
B
B
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
Insert locking nuts
into the front support .
Insert wooden dowels
into the front support .
Insert wooden dowels
into the long plinth .
Repeat with the short
plinth .
18
18
19
19
9
9
9
F
A
F
A
H
H
H
H
H
H
H
H
A
A
A
A
AA
A
A
A
F
A
A
F
x2
x2
9
a: Inserting dowels
and locking nuts

Assembly Instructions
Step 8
10
C
C
C
D
D
Fitting hinges to doors
Fix 2 hinges to the
flap using screws .
CD
Step 9
10
a: Attaching plinth
Attach feet to the
long plinth
Attach the long plinth
to the short plinth .
b: Attaching plinth
Fit long plinth
& short plinth to the
bottom .
44
R
RR
R
R
R
18
18
18
18
18
18
18
19
19
19
19
19
19
a:
b:
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
sliders in place.
!
10