Argos Atlas 161/5803 User manual

MADE IN
BRITAIN
Dimensions
Width - 47cm
Depth - 50cm
Height - 75cm
Atlas - Internal 3 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 19/03/14
Important - Please read these instructions fully before starting assembly
ALR2958
161/5803
Issue 2 - 13/01/14 - Right Side changed to D2766A.
Issue 3 - 19/03/14 - 4 Plastinails added.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 19kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
13
9
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4 5
Top (D2384A)
(496 x 468mm)
7
6
8
Wrap Back (W387-124)
(387 x 124mm) x 3
Rail (D2386A)
(437 x 60mm) x 2
Drawer Front (D2387A)
(433 x 189mm) x 3
Left Drawer
Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer
Side (W370-124RH)
(370 x 124mm) x 3
Drawer Base (T402-367)
(398 x 367mm) x 3
2
Left Side (D2385A)
(735 x 495mm)
Right Side (D2766A)
(735 x 495mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
I
B
Metal dowel (F901) x 10
C
D E
Large locking
nut (F900) x 4
F
G H
Rule Scissors
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small locking
nut (F3) x 6
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
13mm Screw (F52) x 18
13mm Screw (F63) x 18 Knock-in Peg (F171) x 12
Jb
Jc
Ja
Jd
50mm Screw (F49) x 8
Allen Key (F36) x 1
Hammer
A
Wooden dowel (F22) x 2
K
Wedgefix (F639) x 6
CL Runner
(F904) x 3
DL Runner
(F906) x 3
DR Runner
(F905) x 3
CR Runner
(F903) x 3
400mm long
L
Plastic Nail (F91) x 4

4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the
reference numbers below
Step 1
B
4
6
B
B
D
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
4
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
D
5
6
Attach the drawer
sides to the drawer
fronts
Push the left drawer side
and right drawer
side . onto the back of
the drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
5
6
4
D
D
5
6
Groove
5
DD
B
B
4
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
D
6
5
x 3
x 3 x 3
x 3

4
4
Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer backs
Fit the drawer back .
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
5 6
4
7
5 6
8
7
7
H
5 6
8
H
H
8
5
6
7
5
6
8
x 3
x 3
Step 6Runners must be
pushed up against
the drawer front
5
6
4
x 3
J d
J c
G
G
G
G
DL
DR
Fit runners to the
drawers
Turn the 3 drawer
assemblies over.
Fit runner d , marked
with ‘DR’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. . Use a bradawl to
mark the fixing positions,
then secure with 2
screws .
Fit runner , marked
‘DL’, to the bottom edge
of the left drawer side
using the same method.
5
J d
6
4
G
J c
DR
DL

Assembly Instructions
6
Step 7
Step 8
Prepare the top
Screw 4 metal dowels
into the top . B
B
B
B
Plain chipboard
surface
3
B
3
Finished
front edge
Fit the wedgefixes
Slide 1 wedgefix into
the small groove located
on the back of the
drawer front and 1
into the small groove in
the drawer back .
Once in place, tighten up
the screws in the
wedgefixes .
K
4
7
K
4
K
K
7
x 3

Assembly Instructions
7
Step 9
A
a:
b:
J a
F
Finished front edge
F
1st
screw
2nd
screw
F
3rd
screw
J a
Finished front edge
G
G
C
C
C
Prepare the left side
a: Fit runners to
the left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
J a
1
F
F
G
J a
C
1
10mm
A
A
1
1
CL
F
F
F
CL
F
F
F
CL
F
F
F
Ja
Ja
Ja
1
CL
CL
CL
G
G
Finished
front edge
Finished front edge

Assembly Instructions
8
Step 10
A
J b
F
Finished front edge
F1st
screw
2nd
screw
F3rd
screw
J b
Finished front edge
G
Finished
front edge
Prepare the right side
a: Fit runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Insert 2 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
J b
2
F
F
G
J b
C
2
Finished
front edge
a:
b:
C
A
2
2
J b
CR
CR
H
F
H
F
H
F
J b
CR
F
F
F
J b
CR
F
F
F
2
CR
CR
CR
G
G
G
C

Assembly Instructions
9
Step 11
Fit the top
Push the top onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
3
C
C
C
B
2
2
3
Finished
front edge
Step 12
Fit the 2 rails
Fit the 2 rails onto
the right side using 4
screws and tighten
using the allen key .
2
9
E
3
Plain
chipboard
surface
I
I
9
I
I
I
E
CR
CR
CR
9
3
3
CR
CR
CR
I
E
I
I
I
1
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
1
C
1
9
9
Fit the 2 rails onto
the left side using 4
screws and tighten
using the allen key .
1
9
E
I