Aries 2072101 User manual

PAGE 1 • 2072101-INS-RB• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Product Image
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To protect the product, wax after installing. Regular waxing is recommended
to add a protective layer over the finish. Do not use any type of polish or wax
that may contain abrasives that could damage the finish.
For polished, gloss and other smooth finishes,
polish may be used to clear small scratches and scuffs on the finish.
Mild automotive detergent may be used to clean the product.
Do not use dish detergent, abrasive cleaners, abrasive pads,
wire brushes or other similar products that may damage the finish.
Refer to the table to the left when securing hardware during the
installation process to help prevent damage to the product or vehicle.
Level of Difficulty
Moderate
Parts List
1Winch support bracket
2Nut plate
2Hex bolt, M10 x 30mm
2Flat washer, M10
2Lock washer, M10
2Hex bolt, M12 x 30mm
2Flat washer, M12
2Lock washer, M12
Tools Required
Ratchet Torque wrench
Phillips
screwdriver
Flathead
screwdriver
10mm socket Deburring tool
16mm socket Touch-up paint
18mm socket Masking tape
Cut-off tool
Scan
for helpful
install tips
INSTALLATION MANUAL 2072101
Torque Specifications
METRIC
M6 bolt 3 ft.-lbs.
M8 bolt 7 ft.-lbs.
M10 bolt 25 ft.-lbs.
M12 bolt 45 ft.-lbs.
SAE
1/4" bolt 3 ft.-lbs.
5/16" bolt 7 ft.-lbs.
3/8" bolt 16 ft.-lbs.
7/16" bolt 20 ft.-lbs.
1/2" bolt 28 ft.-lbs.
Use above torque setting
unless otherwise noted

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 2072101-INS-RB• PAGE 2
Step 1
Using a flat head screwdriver, pry
and remove the four plastic push pins
securing the air dam in place. Remove
the air dam from underneath the vehicle.
Once removed, pry off the fasteners
securing the brackets to the frame.
Step 2
From behind the bumper, disconnect
the wiring harness attached to each fog
light. Unclip the wiring harness from the
bumper cover
Step 3
Locate the two fasteners securing
the frame cover in place on top of
the bumper. Remove these with a
Phillips screwdriver.

PAGE 3 • 2072101-INS-RB• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 4
When facing the Jeep head-on,
slide the cover to the left to expose
the driver side bolts securing the bumper
in place. Remove the four nuts securing
the bolts onto the bumper frame with an
18mm socket.
Repeat this step on the passenger side.
Step 5
When all the bolts have been removed,
carefully lift the bumper from the frame
and set on a flat work surface.
Step 6
Remove the front bolt securing
the vacuum pump to the frame.
Loosen the rear bolt securing the
vacuum pump to the frame and
rotate it to the left.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 2072101-INS-RB• PAGE 4
Step 9
Tuck the fog light wiring harness
into the frame channel.
Insert a nut plate, aligning the two
threaded holes with the holes in
the Jeep frame. Temporarily hold
in place with tape.
Repeat this process on the driver side.
Step 8
Pull out the wiring harness from
the side of the frame and place
tape on the nut plates.
Step 7
Cut off the vacuum bracket as shown
and deburr the cut edge. Use touch up
paint to protect raw metal.

PAGE 5 • 2072101-INS-RB• 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 10
Set the winch support bracket in place
making sure the wiring harness is routed
below the bracket as shown.
Step 11
Insert the M12 and M10 bolts with
flat washers and lock washers.
Repeat this step on the driver side.
Do not tighten fasteners
until all four bolts are started.
Step 12
Remove the tape from both nut plates.
Using a torque wrench, torque
the M10 bolts to 25 ft./lbs. and
the M12 bolts to 45 ft./lbs.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • 2072101-INS-RB• PAGE 6
Step 13
Congratulations on the installation
of your new winch support bracket.
With the winch support bracket installed,
periodic inspections should be
performed to ensure all mounting
hardware remains tight.
Note: Please refer to the instructions
provided with the front bumper, and
the winch manufacturers instructions
to complete the installation.