Aries 203014 User manual

Page 1 of 3 1/13/2010
PARTS LIST:
Qty Description Qty Description
1 Driver/Left Side Bar 4 12mm Flat Washer
1 Passenger/Right Side Bar 4 12mm Lock Washer
1 Driver/Left Front Mounting Bracket 4 10mm Clip Nuts
1 Passenger/Right Front Mounting Bracket 12 10mm x 30mm Hex Bolt
1 Driver/Left Rear Mounting Bracket 20 10mm x Flat Washer
1 Passenger/ Rear Mounting Bracket 12 10mm x Lock Washer
4 12mm x 50mm Hex Bolt 8 10mm x Hex Nut
INSTALLATION INSTRUCTIONS
203014 / 203014-2
1999-10 FORD F250/350 SUP.DTY.REG CAB
Drive
r
Rear
Mounting Brackets
Passenger F
r
ont
Mounting Brackets
Driver/Left side
Side bar
Passenger/Right
Side bar
Front
Driver F
r
ont
Mounting Brackets
Passenge
r
Rear
Mounting Brackets

Page 2 of 3 1/13/2010
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting with the Driver/Left side, Proceed with your install by locating the factory mounting
holes underneath Vehicle (Fig 1) shows location of mounting holes, note: on some vehicles
you may need to remove the factory tape covering these holes. Install the 10mm Clip nuts as
seen in (Fig 1A)Select the Driver/Left side front mounting bracket from the list above, and
attach to Vehicle with the supplied (3) 10mm Hex bolts (5) 10mm flat washers (3) 10mm lock
washers & (2) 10mm Hex Nuts (Fig 1B) shows bracket attached. Snug but do not tighten
hardware at this time.
3. Begin to now install the Driver/Left rear mounting brackets (Fig 2) shows location of mounting
holes, note: on some vehicles you may need to remove the factory tape covering these holes.
Install the 10mm Clip nuts as seen in (Fig 2A)Select the Driver/Left side rear mounting bracket
from the list above, and attach to Vehicle with the supplied (3) 10mm Hex bolts (5) 10mm flat
washers (3) 10mm lock washers & (2) 10mm Hex Nuts (Fig 2B) shows bracket attached. Snug
but do not tighten hardware at this time.
4. With the brackets attached select the Driver/Left sidebar and install to brackets with the
supplied hardware (2) 12mm x 50mm Hex bolts, (2) 12mm flat washers (2) 12mm lock
washers (Fig 4) shows front bracket attached. Snug but do not tighten hardware at this time
5. Level and align Sidebar properly; then tighten all hardware at this time.
6. Repeat steps 2-4 for Passenger/right Sidebar.
7. Do periodic inspections to the installation to make sure all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives
that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
DRIVER/LEFT SIDE INSTALLATION PICTURED
Fig 1A
Fig 1 Driver/Left side
Front mounting
holes
Driver/Left side
Front clip nut
installed

Page 3 of 3 1/13/2010
DRIVER/LEFT SIDE INSTALLATION PICTURED
Fig 1B
Fig 2A Fig 2B
Fig 2
Driver/Left side
Rear mounting
bracket
Fig 4
(3)10mm Hex Bolt
(5)10mm flat washer
(3)10mm Lock Washer
(2)10mm Nuts
Driver/Left side
Rear mounting
holes
Driver/Left side
Rear clip nut
installed
(3)10mm Hex Bolt
(5)10mm flat washer
(3)10mm Lock Washer
(2)10mm Nuts
(1)12mm Hex Bolt
(1)12mm Flat Washer
(1)12mm Lock Washer