Aries S223015-2 User manual

PAGE 1 • S223015-2-INS-RA • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Product Image
Brackets
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To protect the product, wax after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may
contain abrasives that could damage the finish.
For stainless steel and aluminum, polish may be used to clear small scratches
and scuffs on the finish. Mild soap may be used also to clean the product.
Refer to the table to the left when securing hardware during the
installation process to help prevent damage to the product or vehicle.
Level of Difficulty
Easy
Tools Required
Ratchet Torque wrench
Tape measure Wrench, 17mm
Socket, 17mm Level
Scan
for helpful
install tips
Front
Rear
INSTALLATION MANUAL S223015-2
Torque Specifications
METRIC
M6 bolt 3 ft.-lbs.
M8 bolt 7 ft.-lbs.
M10 bolt 16 ft.-lbs.
M12 bolt 28 ft.-lbs.
SAE
1/4" bolt 3 ft.-lbs.
5/16" bolt 7 ft.-lbs.
3/8" bolt 16 ft.-lbs.
7/16" bolt 20 ft.-lbs.
1/2" bolt 28 ft.-lbs.
Use above torque setting
unless otherwise noted
Parts List
1Driver / left side bar
1Passenger / right side bar
1Driver / left front bracket
1Passenger / right front bracket
1Driver / left rear bracket
1Passenger / right rear bracket
24 Hex bolt, M10 x 35mm
8Hex nut, M10
24 Flat washer,
M10 x 30mm OD x 1.5mm
8Flat washer,
M10 x 22mm OD x 2mm
24 Lock washer, M10
8Clip nut, M10

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • S223015-2-INS-RB • PAGE 2
Step 1
Starting on the driver side, locate the
three mounting locations along the body.
This installation will use the front and rear
mounting points.
Step 2
The mounting brackets are specific to
a front or rear mounting location. When
mounting the brackets, have the cradle
facing toward the middle of the truck for
proper placement.
Step 3
Starting at the front, remove the factory
tape or plug covering the mounting holes
on the inner rocker panel.
Insert an M10 clip nut onto
each mounting point.
Step 4
Lift the bracket into place and attach
with an M10 hex bolt, locking washer
and 30mm OD flat washer into the
rocker panel and mounting tabs.
Snug the hardware,
but do not fully tighten.

PAGE 3 • S223015-2-INS-RA • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 5
Repeat this for the
passenger-side bracket.
Step 6
To determine the front of the side bar,
measure from the end of the side bar
to the center of the rivet nut. This
measurement should be 15 1/2".
Step 7
Lift the new side bar into place and
attach with an M10 bolt, locking washer
and 22mm OD flat washer.
Step 8
Check for level and adjust if necessary.
Once aligned, tighten all hardware.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • S223015-2-INS-RB • PAGE 4
Step 9
Repeat this entire process on the
passenger side.
Step 10
Congratulation on the installation of
your new ARIES 4" oval side bars.
With the side bars installed, periodic
inspections should be performed to ensure
all mounting hardware remains tight.
To protect your investment, see the
'Notes and Maintenance' section on
the first page of this instruction manual.