Aristel AN1204 User manual

AN1204 3G Intercom 1 Revision E16 ,Oct 2015
ARISTEL NETWORKS
MANUAL
DOORINTERCOM
AN1204 3G INTERCOM
(ACCESS CONTROL SYSTEM)
For your protection, read these instructions completely
And keep them for future reference.

AN1204 3G Intercom 2 Revision E16 ,Oct 2015
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTION .................................................................................................3
AN1204 3G INTERCOM INTRODUCTION .........................................................................................4
AN1204 3G INTERCOM WITH ACCESSORIES ...................................................................................4
INSTALLATION ..................................................................................................................................5
AN1204 3G Intercom Unit ..........................................................................................................6
Wiring Diagram.............................................................................................................................6
LED Indicator ...............................................................................................................................7
AN1204 3G INTERCOM OPERATION ................................................................................................8
Enter Listener Monitoring Mode ................................................................................................10
Enter Access Control Mode ........................................................................................................10
Enter Programming Mode ..........................................................................................................10
Programming ..............................................................................................................................11
Door/ Gate Release ...................................................................................................................12
Check 3G Signal Strength ..........................................................................................................14
Check Relay Status ....................................................................................................................14
Administrator Number....................................................................................................14
CHECK A LOG OF DIAL IN AND DIAL OUT NUMBERS VIA E-MAIL OR SMS ...................................15
USER COMMANDS .........................................................................................................................18
HOW TO RESET THE HARDWARE WHEN YOU FORGET YOUR PASSWORD.........20
SPECIFICATIONS..............................................................................................................................20
QUICK PROGRAMMING VIA SMS ..................................................................................................21
TROUBLESHOOTING (Q&A) ...........................................................................................................22

AN1204 3G Intercom 3 Revision E16 ,Oct 2015
Thank you for purchasing an AN1204 3G Intercom. Please read this manual carefully before using.
Be sure to keep this manual for future reference in case of any problem or question should arise.
IMPORTANT SAFTY INSTRUCTIONS
When using this AN1204 3G Intercom, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and personal injury. Please read the following before using your equipment.
1. Follow all warning and instructions on the product.
2. Unplug all the connections of product before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
3. Do not use this product near water.
4. Do not use this product near an area where there is a potential of gas leaks or near any fumes that can
be explosive.
5. Do not place this equipment near or over a radiator or any other heat source.
6. Do not overload the wall outlet or power cord where the power adapter is installed. This can result in
fire or electric shock
7. Avoid spilling liquid on this equipment and do not insert any objects through the ventilation slots.
8. Avoid using the equipment during an electrical storm. There is a remote risk of electrical shock from
lighting.

AN1204 3G Intercom 4 Revision E16 ,Oct 2015
AN1204 3G INTERCOM INTRODUCTION
The AN1204 3G is an intercom system, installed at the entrance of a building. It is an ideal product replacing
the traditional door phone. It allows you to speak with visitors standing at the entrance of your company or
house entrance from a remote location. A visitor, by simply pressing the call button establishes a mobile
call with you. During the call you will be able to activate realty.
This AN1204 3G Intercom gives you the opportunity not only to know who is waiting at the entrance from a
remote location but also to control the access point. Use of AN1204 3G Intercom at your company or house
does not require any special installation and wiring. Simply install the AN1204 3G and connect the door
latch and power supply.
AN1204 3G INTERCOM WITH ACCESSORIES
Item
Description
Q’ty
Included
Optional
1
AN1204 3G Intercom
1
◎
2
Power adapter
1
◎
3
External antenna
1
◎
4
Mounting Bracket for antenna
1
◎
5
Operational manual
1
◎

AN1204 3G Intercom 5 Revision E16 ,Oct 2015
INSTALLATION
This 3G Intercom is suitable for both flush and surface mounting.
Note:
For surface mounting, you will have to remove the plastic enclosure before fitting main station into the
stainless steel cabinet.

AN1204 3G Intercom 6 Revision E16 ,Oct 2015
AN1024 3G Intercom Unit
Wiring Diagram
Call Button
Speaker
Microphone

AN1204 3G Intercom 7 Revision E16 ,Oct 2015
LED INDICATORS
1. LED “Intercom Status “ Indicator
LED
Status
Yellow (standby)
Flashes once per 5 seconds
Yellow (using)
Solid
2. LED ‘Network “Indicator
LED
Status
Green (ready)
Flashes once per 3 seconds
Green (searching)
Flashes once per second
Green (busy)
Solid
3. LED “ Power “ Indicator
LED
Status
Red (power on)
Solid
Red (power off)
Off
1. SIM card
Register your SIM card with the network, and check it works in a mobile phone
You MUST remove the PIN request from the SIM before inserting it in the AN1204 3G.
Ensure the power is OFF before inserting the SIM card. Carefully side the SIM holder in the OPEN
direction, insert the SIM, and slide in the CLOSED direction to lock it in place.
2. Antenna
Install the antenna as high as possible on the top of the pillar for best possible reception.
3. Door Lock
Connect an electric door lock to terminals marked “door latch”.
4. Power Supply
Connect a 12 volt DC power supply to terminals marked “AC, AC”
The power supply should be capable of supplying a constant current of no less than 1amp.
5. After a final check of wiring , switch on the power
6. Allow 20~30 seconds for the unit to boot up and detect the network. Once successful connection has
been made, the unit will sound a confirmation tone and the status LED will begin flashing.

AN1204 3G Intercom 8 Revision E16 ,Oct 2015
AN1204 3G INTERCOM OPERATION
When the visitor pushes the call button to activate the AN1204 3G ring tone will be heard from the 3G
intercom. At the same time connection is established with the phone number that is stored in the AN1204
3G. If the first number is busy or not answered the call can be diverted to the second and the third.. The
remote phone answers the call from AN1204 3G and starts conversation with the visitors. During
conversation press * on your mobile for door open. The relay switches can also be temporarily or
permanently switched on or off by press # and 1.
Enter system menu
There are three different modes under system menu.
1. Listener monitoring mode
2. Access control mode
3. Programming mode
To gain access to the system menu via dial in, follows these steps:
1. Call the telephone number of the 3G intercom
2. Wait for the intercom to answer and signal by one beep to enter system menu
3. Enter the password of the mode you would like to enter
4. Password correct one beep, password error 3 beeps.
5. 3 times failure attempt on password , hang up the call

AN1204 3G Intercom 9 Revision E16 ,Oct 2015

AN1204 3G Intercom 10 Revision E16 ,Oct 2015
Enter Listener Monitoring Mode
1. Call the telephone number of the 3G intercom
2. This device will then verify your phone number with your predefined numbers.
3. You will hear a “Do” tone to enter listener monitoring mode by pressing【*13*1212＃】where
1212 is the password.
4. You are now in the” listener monitoring mode”.(you can hear the live sound of the intercom’s
surrounding environment)
* Under this mode speaker is OFF.( 35＃: turn on speaker )
* You can still control the relay output when you are under listener monitoring mode but speaker must
be ON status.
Enter Access Control Mode
1. Call the telephone number of the 3G intercom.
2. This device will then verify your phone number with your predefined numbers.
3. You will hear a “Do” tone to enter access control mode by pressing【*33*5678＃】where 5678 is
the password.
4. The door will be opened after enter the correct password
*(To open the door by password, if the number is not stored in the access control section)
Enter Programming Mode
1. Call the telephone number of the 3G intercom
2. This device will then verify your phone number with your predefined numbers.
3. You will hear a “Do” tone to enter into programming mode by pressing【*12* 1234＃】where
1234 is the password.
4. You are now in the “programming mode”
Note: At the end of each command there can be one of the two indications:
Successful: a long “beep” tone, failed: three short “beep” tone.
5. To make changes on settings please refer to the user commands.(P15,16)
6. To end programming mode just hang up.
NOTE:
*To be successful in programming, originate a call from a land line and enter the digits slowly or using
programming by text message.