Aristel AN1808-12S User manual

AN1808-12S 4G Audio Intercom (E2.2) 1/16
AN1808-12S 4G LTE
INTERCOM &ACCESS CONTROL
OPERATING MANUAL
For your protection, read these instructions completely
Keep for future reference.

AN1808-12S 4G Audio Intercom (E2.2) 2/16
TABLE OF CONTENTS
Important Safety Instructions........................................................................................3
Introduction ................................................................................................................... 4
Parts List........................................................................................................................4
Installation.....................................................................................................................5
Using the AN1808-12S...................................................................................................9
1. Setting your call out numbers.............................................................................9
2. Setting your dial in numbers (Guest list )........................................................... 9
3. App on iOS and Android....................................................................................9
Enter System Menu.....................................................................................................10
Programming by text message .................................................................................... 11
Command Codes ......................................................................................................... 12
Hardware reset (if you forget password)..................................................................... 15
How to change the name plate ....................................................................................14
Troubleshooting (Q &A).............................................................................................15
Specification:...............................................................................................................16
Setting your PINs............................................................................................... 9
4.

AN1808-12S 4G Audio Intercom (E2.2) 3/16
Thank you for purchasing AN1808-12S 4G audio intercom. Please read this manual carefully
before using.
Be sure to keep this manual for future reference in case of any problem or questions.
Important Safety Instructions
When using this intercom, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and personal injury. Please read the following before using your equipment.
1. Follow all warning and instructions on the product.
2. Unplug all the connections of product before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
3. Do not use this product near water.
4. Do not use this product near an area where there is a potential of gas leaks or near any fumes that
can be explosive.
5. Do not place this equipment near or over a radiator or any other heat source.
6. Do not overload the wall outlet or power cord where the power adapter is installed. This can result
in fire or electric shock
7. Avoid spilling liquid on this equipment and do not insert any objects through the ventilation slots.
8. Avoid using the equipment during an electrical storm. There is a remote risk of electrical shock
from lighting.

AN1808-12S 4G Audio Intercom (E2.2) 4/16
Introduction
The 4G Door Station AN1808-12S isan intercom system andaccess control device which can be
installed at the entrance of a building, gate, fence or door. The device can operate on local 12-24V
AC orDC power. It enables you to speak with visitors, from any location, on or off the premises.
Door orgate release isactivated from your phone keypad by pressing * during the conversation and
can also be activated by calling the SIM card in the unit from an authorized phone number (guest).
The intercom will recognize an authorized phone (guest) number calling it, and then not answer the
call, but will release the door or gate. This call is free.
This intercom supports all Telstra, Optus & Vodafone CSFB networks.
.
Parts List
Item Description Q’ty
1 AN1808-12S 4G audio intercom 1
2 Power adapter 1
3 Antenna with 3 metre tail. 1
4 Mounting Bracket for antenna 1
5 Operating manual 1
6 6 Pin Cable 1
7 Terminal Blocks 1
Mounting Bracket

AN1808-12S 4G Audio Intercom (E2.2) 5/16
Installation
This intercom is suitable for both flush mounting and surface mounting.
Keypad
Speake
Microphone
Call button

AN1808-12S 4G Audio Intercom (E2.2) 6/16
1. SIM card installation (Fig 1)
1.1 Disconnect the power from the intercom
1.2 Remove the rear plastic cover
1.3 Remove the SIM card cover from the bottom of the unit
1.4 Slide the SIM card holder towards the front of the unit
1.5 Lift up the holder
1.6 Before inserting the SIM card, ensure that it is not PIN number locked. (If
locked, use a mobile phone to unlock it).
1.7 Insert the SIM card (Note orientation of notched corner)
1.8 Replace holder and slide towards the rear of the unit to lock in place
1.9 Replace rear plastic cover

AN1808-12S 4G Audio Intercom (E2.2) 7/16
2. Connecting with the door lock system (Fig 2)
2.1 According your door lock type, see wiring diagram below.
3. Connecting the Antenna (Fig 3)
3.1 Plug in the antenna cord to the connector on the rear of the unit
3.2 Place antenna away from electrical/electronic systems (computers, microwave ovens,
etc.)

AN1808-12S 4G Audio Intercom (E2.2) 8/16
4. Power on.
4.1 Connect the 12-24v power source to the connector marked AC
4.2 The blue indicator of call button should be on and you will hear Du Du tone.
4.3 Position the intercom where it will be installed.
4.4 When the Du Du tone has ceased, the device is ready.
Wiring Diagram

AN1808-12S 4G Audio Intercom (E2.2) 9/16
Using the AN1808-12S
1. Setting your call out numbers
1.1 Send the text SMS to the number of device.
1.2 The format of text SMS is
*12*1234#11[call out number 1]#12[call out number 2]#13[call out number 3]#
1.3 When the setting is finished, the sender will receive the reply as below.
11[call out number 1]#12[call out number 2]#13[call out number 3]#OK
1.4 If you press the call button of device, it will call the numbers in sequence.
2. Setting your dial in numbers ( Guest list )
2.1 Send the text SMS to the number of device.
2.2 The format of text SMS is
*12*1234#71[country code]#72[relay][call in number 1]# 72[relay][call in number 2]#...
2.3 When the setting is finished, the sender will receive the reply as below.
71[country code]#72[relay][call in number 1]# 72[relay][call in number 2]#...OK
2.4 If a guest calls the number of the device, it will trigger the relay to control the door
latch.
2.5 If the number is not on the guest list, the device will answer and sound a beep. Then
the administrator can enter the programming mode by password.
4.App on iOS and Android
3.1 Please search 4G intercom on Apple store or Google Play
3.2 The App can help you to program the device more easily.
3.3 You can use the App to unlock the door viacalling orSMS.
3. Setting your PIN numbers
3.1 The format of text SMS is
*12*1234#895[X]#87[relay][pin code 1]# 87[relay][pin code 2]#87[relay][pin code 3]#...
3.2 When the setting is finished, the sender will receive the reply as below.
895[X]#87[relay][pin code 1]# 87[relay][pin code 2]#87[relay][pin code 3]#...OK
3.3 If you press the correct PIN code then the device will trigger the relay to open.

AN1808-12S 4G Audio Intercom (E2.2) 10/16
Enter System Menu
1. Please call the number of the intercom.
2. The device will answer and sound one beep to enter system menu.
3. Enter the password of the mode you would like to enter.
3.1 Listener monitoring mode. 【*13*1212
＃
】
3.2 Access control mode 【*33*5678
＃
】
3.3 Program setting mode 【*12* 1234
＃
】
4. Password correct one is beep, password error is 3 beeps.
5. The device will hand up after 3 failed attempts.
Enter Listener Monitoring Mode
1. You will hear a “Do” tone to enter listener monitoring mode by pressing【*13*1212
＃
】
where 1212 is the monitoring password.
2. Then you can hear the live sound of the device’s surrounding environment.
* Under this mode speaker is OFF. (35
＃
: To turn on speaker)
* You can still control the relay output under listener monitoring mode but speaker must be
ON status.
Enter Access Control Mode
1. You will hear a “Do” tone to enter access control mode by pressing【*33*5678
＃
】where
5678 is the access control password.
2. The door will be opened after enter the correct password
*(To open the door by password, if the number is not stored in the access control section)
Enter Program setting Mode
1. You will hear a “Do” tone to enter into program setting mode by pressing【*12* 1234
＃
】where 1234 is the setting password.
2. You are now in the “program setting mode”
Note: At the end of each command there can be one of the two indications:
Successful: a long “beep” tone, failed: three short “beep” tone.
3. To make changes on settings please refer to the command codes in page 12.
4. To end program setting mode just hang up.
NOTE:
*To be successful in programming, originate a call from a land line and enter the
digits slowly or using programming by text message.