Aristel SD-902 User manual

1
Quick Guide for SD-902 Door phone Intercom

2
Overview
This document describes the features of Door phone Intercom (SD-902) and
uses several examples to illustrate its settings.
Pre-Requisites
SN-902 V2 Base
SN-902 V2 Handset (HS) with new firmware which supports the SD902
SD-902 intercom
Feature List
Works with SN-902 v2 SPK handset, base and land line.
Supports either two way intercom (Intercom to handset) or land
line call via the base unit.
Outgoing call from DS: calls up to 3 numbers
Incoming call to DS: programmable auto-answer mode
Accepts 2 to 4-digits code to control the door relay
Stores 90 numbers on authorized guest list: if caller ID matches
the pre-stored number in the phone book, the DS will open the
door/gate automatically without inputting the password.
Option 1: Setting DS by DS Main Menu
3 sets of phone numbers for outgoing calls: Via MENU, 1, 5, PSTN
90 sets of authorized guests for incoming call: Via MENU,2 →PhoneBook
Menu for DS: Menu →1. KeyGuard → DoorPhone
Item
Description
Default Value
Ring Timeout
Outgoing call from DS. Setting the
ring timeout after pushing the “Call”
button.
35 seconds. (Range: 15~ 254)
Unlock Code
Setting 2 to 4-digit code of opening
door. 1 digit access not supported.
****
Auto-Answer
This function will be enabled always
for setting DS from HS directly.
ON

3
Relay Timer
Setting the relay duration.
2 seconds.
(Range: 1~15)
Call Mode
Selecting destination (telephone/HS)
to answer the call from DS.
PSTN/HSID: 13
(HSID Range: 11~19, 21~29,
31~39, 41~49)
Table 1: The Descriptions of DS items
-Menu for DS – You can see the menu from DS (menu →1)
Menu →1. DoorPhone
Figure 1: The Menu of DS
1. Ring Time Out
You can enter the value of ring timeout (15~254 seconds) here, and if you
enter an invalid value and it will revert to the previous valid value stored.
Figure 2: Setting Ring Timeout
2. Unlock Code
You can enter a 2 to 4-digits code (it can be composited by 0~9 and *) here,
and the length of code must be 2 to 4 digits.
Figure 3: Setting Code of Opening Door
3. Auto-Answer
It is enabled always for the feature that can set DS by cordless HS.

4
4. Relay Timer
You can enter the value of relay duration to control the relay of DS, and if
you enter an invalid value and it will revert to the previous valid value stored.
Figure 4: Setting Relay Duration
5. Call Mode
You can select a HS or telephone here for answering the call from DS.
-PSTN: Just save and DO NOT FORGET to set telephone number or nothing
will happen when pushing the “Call” button. You can follow the steps as
Figure 5 to set the number and you can enter 3 sets of number to DS.
Figure 5: Setting Call Mode (PSTN).
-INTERCOM: Press up/down key, you will see INTERCOM and can set HS ID
after pressing ‘NEXT’, if you enter an invalid ID and it will revert to the ID
stored before. Please note that if you choose PSTN and save, the HS ID
will be reset to default ID.
Figure 6: Setting Call Mode (HS). Figure 7: Setting HS ID.
-After DS Setting
You must power cycle the DS off/on, in order for any change to take effect

5
Option 2: Setting DS by cordless HS
You have to know the ID of DS before setting this way.
These functions can be set using HS11 and HS12.
There is a programing menu for setting DS.
You can explore the KEY MAP of HS (see Figure 8) first before setting.
Figure 8
You should understand the setting flow of the HS and can reference Figure
9. If you want to leave the programing menu, press the END key anywhere
and it will return to IDLE state of HS.
Figure 9: The flow of programing menu.

6
Item
Description
Call Mode
There are two modes for DS, one is INT mode and the other
is PSTN mode. You can refer the section ‘Call Mode’ to fully
understand it.
Indication HS ID
In INT mode, a HS ID will be assigned to DS and the HS will
ring when DS ‘Call’ button is pressed. You can see the
section ‘Call Mode’ to fully understand it .
Code
Enter the code to open the door. See section ‘Unlock Code’.
Speaker Volume
The volume of DS and the default value is 3.
Dial Out Nmber1
In PSTN mode, the telephone will ring when pushing ‘Call’
button of DS and you should store the ‘Dial Out Number’ in
advance. See section ‘Call Mode’.
Dial Out Nmber2
It is the same as the item ‘Dial Out Number1’.
Dial Out Nmber3
It is the same as the item ‘Dial Out Number1’.
Ring Timeout
See ‘Ring Time Out’.
Relay Timer
See ‘Relay Timer’.
Guest List
Enable/disable the guest list. When you enable it, the guest,
whose number is in your guest list, will cause the door /gate
to open automatically when he/she makes a call to the DS.
Table 2: The Descriptions of Programing Menu Items.
-Push the call button to register
Try the easy way to register your DS, just follow the steps listed below:
1. Using the admin HS (The ID is 11 or 12) to assign an ID for DS
A. Menu →9.System
B. Enter Base ID for entering the System menu, in our case, the ID is 10.
C. After entering the menu, go to the item ‘4.Assign HS’.
D. Assign an ID you want for DS.
2. Long press the REGISTER KEY of BASE until in register mode.
3. Long press the CALL BUTTON of DS and power it on and it will be registered
to the base automatically.

7
-HS To DS – You can set DS by HS directly
We provide another convenient way to modify DS mode, code, speaker
volume…etc. You have to know the ID of your DS before setting. For example, a user
wants to modify the DS mode to INT mode and he/she will make an intercom call to
DS, and press the RIGHT key, the HS will show the user the option of mode
(INTERCOM:0, PSTN:2) and press key ‘0’. After setting, the DS mode will be changed
to mode INT automatically.
The following section will show you the setting steps of ‘HS to DS’.
Call Mode
Steps:
1. Press the ‘INTERCOM’ key and enter the ID of DS.
2. Press the ‘RIGHT’ key until you see the options of changing DS mode (see
Figure 10)
3. Press ‘0’ or ‘2’ to change the mode you want.
Figure 10
Indication HS ID
Steps:
1. Press the ‘INTERCOM’ key and enter the ID of DS.
2. Press the RIGHT key until the HS show you the string ‘IND HS ID’ such as
Figure 11.
3. Enter the indication HS ID you want, and note that you can’t enter the DS’ ID.
Figure 11

8
Code
Steps:
1. Press Key ‘INTERCOM’ and enter the ID of DS.
2. Press the RIGHT key until the HS shows you the string ‘ENTER NEW CODE’
such as Figure 12.
3. Enter the new code of opening door.
Figure 12
Note:
The code can be a 2 to 4-digits, and if you want to use a 2 or 3-digits to be your
code, you should enter ‘#’ to tell the DS the completion of changing code. For
instance: You want to use ‘11’ be your code, you should type ‘11#’.
Speaker Volume
Steps:
1. Press Key ‘INTERCOM’ and enter the ID of DS.
2. Press the RIGHT key until the HS show you the string ‘VOLUME: 1-6’ such as
Figure 13.
3. Press the value to change the volume you want.
Figure 13

9
Dial Out Numbers 1/2/3:
Steps:
1. Press Key ‘INTERCOM’ and enter the ID of DS.
2. Press the RIGHT key until the HS show you the string ‘DIAL OUT NUM1’/‘DIAL
OUT NUM2’/‘DIAL OUT NUM3’ such as Figure 14/15/16.
3. Enter the number you want.
Figure 14 Figure 15 Figure 16
Note:
1. The MAX length of dial out number is 16.
2. The number can be composed by 0 to 9 and ‘*’ just.
3. If your number’s length is smaller than 16, you should type ‘#’ to tell DS the
procedure is done. For example: your number is ‘123456789’ and you should
type ‘123456789#’.
4. You can type ‘#’ only to clear it.
Ring Timeout
Steps:
1. Press Key ‘INTERCOM’ and enter the ID of DS.
2. Press the RIGHT key until the HS show you the string ‘RING TIMEOUT’ such as
Figure 18.
3. Enter the value of timeout you want.
Figure 18
Note:
1. The value of ‘RING TIMEOUT’ should be 16 to 254.
2. If you want to complete the setting, you can type ‘#’.
3. It will become default value when you type ‘#’ only.

10
Relay Timer
Steps:
1. Press Key ‘INTERCOM’ and enter the ID of DS.
2. Press the RIGHT key until the HS show you the string ‘RELAY TIMER’ such as
Figure 19.
3. Enter the value of relay timer you want.
Figure 19
Note:
1. The value of ‘RELAY TIMER’ should be 1 to 15.
2. If you want to complete the setting, you can type ‘#’.
3. It will become default value when you type ‘# only’
Guest List
Steps:
1. Press Key ‘INTERCOM’ and enter the ID of DS.
2. Press the RIGHT key until the HS show you the string ‘RELAY TIMER’ such as
Figure 20.
3. Enter the value of relay timer you want.
Figure 20