ARJO HUNTLEIGH Kwiktrak Gate User manual

KWIKtrak Gate
Instruction for Use
001-11502-EN rev. 6 • June 2013

Design Policy and Copyright
® and ™ are trademarks belonging to the ArjoHuntleigh group of companies.
© ArjoHuntleigh 2013.
As our policy is one of continuous improvement, we reserve the right to modify designs without
prior notice. The content of this publication may not be copied either whole or in part without the
consent of ArjoHuntleigh.

001-11502-EN rev. 6
Table of Contents iii
Table of Contents
Foreword......................................................................................................................................1
Please Read this Manual Thoroughly!..................................................................................................... 1
Service and Support ................................................................................................................................ 1
Manufacturer Information......................................................................................................................... 1
Denitions Used in this Manual ............................................................................................................... 1
Safety Instructions......................................................................................................................2
Operational Life ....................................................................................................................................... 2
Product Identication ............................................................................................................................... 2
How to Use this Manual........................................................................................................................... 2
Safe Working Load .................................................................................................................................. 3
Important Safety Directions ..................................................................................................................... 3
Shock Prevention..................................................................................................................................... 3
Environmental Advice .............................................................................................................................. 3
Homecare Environment Considerations.................................................................................................. 3
Symbols Used..............................................................................................................................4
General Symbols ..................................................................................................................................... 4
Product Description / Labels......................................................................................................5
How to use the KWIKtrakGate ..................................................................................................6
Crossing the Gate.................................................................................................................................... 6
Using the Gate System............................................................................................................................ 6
Troubleshooting ..........................................................................................................................8
Care and Maintenance ................................................................................................................8
Preventive Maintenance Schedule .......................................................................................................... 8
Annual Inspection by an Authorized Technician ...................................................................................... 8
Cleaning................................................................................................................................................... 8
Technical Specications.............................................................................................................9
Product Dimensions..................................................................................................................10
Dimensions..........................................................................................................................................................10
Electromagnetic Compatibility.................................................................................................11
Electromagnetic Compliance..................................................................................................................11
Electromagnetic Emissions.....................................................................................................................11
Electromagnetic Immunity ..................................................................................................................... 12

001-11502-EN rev. 6
iv

001-11502-EN rev. 6
Foreword 1
Please Read this Manual Thoroughly!
The information in this manual is crucial to the
proper use and maintenance of the
KWIKtrak® Gate system. It will help protect your
product as well as ensure that it performs to
your satisfaction.
Lifting and transferring a person always
presents a potential risk. This manual contains
safety related information that must be read
and understood to help prevent injuries.
WARNING: ArjoHuntleigh strongly advises
and warns that to avoid injuries that can be
attributed to the use of inadequate parts,
only parts designated by ArjoHuntleigh
should be used on product and other
appliances supplied by ArjoHuntleigh.
WARNING: Unauthorized modications on
any ArjoHuntleigh product may affect its
safety. ArjoHuntleigh will not be held
responsible for any accidents, incidents or
lack of performance that occur as a result of
any unauthorized modication to its products.
Do not attempt to expose, service or repair the
KWIKtrakGate system . If any unit is defective,
contact your local ArjoHuntleigh vendor.
Always ensure that the equipment is installed
and put into service by an authorized
ArjoHuntleigh contractor or installer in
accordance with the information contained in
the accompanying documents.
Service and Support
A service routine has to be done on your
KWIKtrakGate system by ArjoHuntleigh trained
service personnel. This will ensure it remains
safe and functional.
Please contact your local ArjoHuntleigh vendor
for any of the following:
• If you require further information.
• Want to report an unexpected event,
change in the performance or a
malfunction.
• Need any help in setting up, using or
maintaining your KWIKtrakGate.
• Need replacement parts.
Your ArjoHuntleigh vendor can offer support
and service programs to maximize the long-
term safety, reliability and value of the product.
Additional copies of this manual can be
purchased from your local ArjoHuntleigh agent.
When ordering, include the Instructions for Use
part number (see front page) and the product
part number.
Manufacturer Information
This product was manufactured by:
ArjoHuntleigh AB
Verkstadsvägen 5
241 38 Eslöv
SWEDEN
 : [phone]
: [phone]
ü: www.ArjoHuntleigh.com
Denitions Used in this Manual
WARNING:
Means: Failure to understand and follow this
instruction may result in injury to yourself and
others.
CAUTION:
Means: Failure to follow this instruction may
cause damage to the product(s).
NOTE:
Means: Important information regarding correct
use of the product.
Foreword

001-11502-EN rev. 6
Safety Instructions2
Intended Use
The KWIKtrakGate system is a track accessory
to be used with the KWIKtrak track system and
a xed ceiling lift in a homecare setting, at
nursing homes and other assisted living centers.
The gate system allows the ceiling lift to travel
from a mobile track to a xed track and vice
versa. Patient transferring is performed under
the supervision of an appropriately trained
caregiver staff in accordance with the
instructions outlined in this manual. All other
uses must be avoided.
The equipment must only be used for the
purposes stated above, and must be installed
by ArjoHuntleigh authorized personnel and in
accordance with local codes.
WARNING: The KWIKtrakGate system is
not intended to be operated by the patient.
In the event of a malfunction, patient could
get stuck.
WARNING: The KWIKtrakGate system is
for transferring patients only. Do not use the
equipment for any other purpose.
Using this equipment outside the scope of
its intended use could lead to injuries.
Operational Life
This track accessory is designed and tested for
a useful life of 10 000 cycles at maximum safe
working load (SWL), subject to preventive
maintenance as specied in the “Care and
Maintenance” section.
A complete cycle is acheived when the gate is
unlocked to allow the ceiling lift to exit the
mobile track and locked after the ceiling lift has
returned onto the mobile track.
Time equivalence between the number of
cycles versus the number of years is made
clear in the following table.
Cycles per Day Years
(10,000 transfers)
47
6 4.5
83.5
WARNING: The manufacturer cannot
ensure full safety for an accessory of which
the life span has been exceeded. Wear may
cause the breakage of a part and lead to a
patient fall.
The operating life of this equipment corresponds
directly to the safe operating time period before
a complete overhaul is required. Aging of the
equipment, frequency of use (cycles per day),
the weight of the resident and maintenance
frequency are factors that have an impact on
the KWIKtrakGate system’s life span.
Product Identication
The product’s identication number
(specication, model, serial number) appears
on labels on both the motor and xed boxes,
see “Fig. 1” on page 5 for labels positionning.
How to Use this Manual
To ensure the safe operation of the
KWIKtrakGate system, read the entire manual
carefully before operating this equipment.
If anything is not completely understood, please
contact your local ArjoHuntleigh representative
for more details. Failure to comply with warnings
in this manual may result in injuries.
Keep this manual handy and refer to it as
required. Make sure that all operators are
regularly trained in the use of the equipment
according to the information found therein.
The equipment must be used in accordance
with these safety instructions.
Anyone using the equipment must also have
read and understood the instructions in this
manual.
If there is anything you are not sure about,
contact your local ArjoHuntleigh representative.
Safety Instructions

001-11502-EN rev. 6
Safety Instructions 3
Safe Working Load
The KWIKtrakGate system has been designed
to be used with ArjoHuntleigh ceiling lifts with a
safe working load of 272 kg (600 lb) or less.
WARNING: The KWIKtrakGate system is
intended to be used for residents whose
weight is within a specied safe working load
(SWL). Do not attempt to lift more than the
lowest weight limit indicated on the following:
• the track system
• the “maximum load” label on the
ceiling lift
• on the spreader bar
• on the sling.
Overloading any of these elements could
lead to a patient fall.
Important Safety Directions
NOTE: ArjoHuntleigh’s KWIKtrakGate
System is specically designed for KWIKtrak
track systems and ArjoHuntleigh’s ceiling
lifts series #910XXXX, #911XXXX,
#913XXXX, #923XXXX, #LDXXXXX and
MSX1X-XX-XX.
CAUTION: Always keep components of the
KWIKtrakGate system clean and dry and
ensure that the daily check is carried out
before using the lift as instructed in the “Care
and Maintenance”section.
WARNING:It is unsafe to interconnect this
product with other products not described in
the instruction herein.
Shock Prevention
• Do not splash or expose the device to
water or moisture.
• Do not attempt to expose, service or
repair the KWIKtrakGate. If any unit is
defective, contact your local
ArjoHuntleigh vendor.
Environmental Advice
When disposing of any items associated with
the product, contact the appropriate local
authorities for information.
Homecare Environment
Considerations
WARNING: This product contains small
parts that might present a choking hazard
for children if swallowed or inhaled.
WARNING: The KWIKtrakGate is not
intended to be operated by children. Serious
injuries could occur.
NOTE: Rigorous cleaning actions should be
done when the KWIKtrakGate is exposed to
an animal. Pet hair trapped inside the device
can reduce the product performance.

001-11502-EN rev. 6
Symbols Used4
Symbols Used
General Symbols
This symbol points out the
manufacturer’s name and
address. May also point
out manufacturing date.
This symbol means that
the product complies
with the medical device
directive 93 / 42 / EEC.
ISO 15223 3.15
This symbol points out
the manufacturer’s
catalogue number.
ISO 15223 3.16
This symbol points out the
manufacturer’s serial number.
“Separate collection” for all
batteries and accumulators
as per the WEEE Directive.
SWL SWL is the maximum load the
device is rated for safe usage.
This symbol means that
the item can be recycled.
1641
This symbol means that
you must refer to the
Instructions for Use (IFU).
IP N1N2
Degree of protection
provided by enclosure.
N1: Ingress of particles,
N2: Ingress of water.
Conforms to CSA standards.
Direct current.
Alternating current.
Warning symbol. Whenever
this symbol becomes visible
on the Gate System, the
product is not safe to use.

001-11502-EN rev. 6
Product Description / Labels 5
Product Description / Labels
Fig. 1
Product Identication
Warning !
Warning !
Product Identication
1
23
4
4
5
6
8
7
Legend
1) KWIKtrakGate xed track box
2) Energy reserve box
3) KWIKtrakGate motor box
4) Double contact box
5) KWIKtrakGate DF Locker
6) KWIKtrakGate clamp block
7) KWIKtrakGate reinforcement kit
8) KWIKtrakGate xed block

001-11502-EN rev. 6
How to use the KWIKtrakGate6
Crossing the Gate
WARNING:
If you see the warning symbol appearing at the
end of the track, and the mobile track is not aligned
with the xed track, DO NOT use the gate system.
Using the gate when the warning symbol
is visible could lead to a patient fall.
Contact ArjoHuntleigh for assistance.
•
Using the Gate System
1) With the ceiling lift turned on, move it to the activation station next to the gate stopper.
Fig. 2
Contacts aligned with
activation Station
Gate stopper deployed
2) Align the mobile track with the xed track. The gate will clamp both tracks together and the
gate stopper will retract allowing the lift to pass through the gate.
Fig. 3
3) Move the ceiling lift onto the xed track.
How to use the KWIKtrakGate

001-11502-EN rev. 6
How to use the KWIKtrakGate 7
4) When the ceiling lift is returned under activation station #2, the gate stoppers will go back to
their closed position, blocking the end of the tracks.
Fig. 4
Activation Station #2 Activation Station #1
5) The X-Y’s mobile track can again travel freely.
NOTE: The ceiling lift must always be routed slowly under an activation station. If the lift is
moved too quickly, it may not be detected by the station and the gate’s position would remain
unchanged. To close the gate, move the lift slowly under activation station #2.

001-11502-EN rev. 6
Troubleshooting8
Care and Maintenance
Preventive Maintenance Schedule
The KWIKtrakGate is subject to wear and tear, and the following actions must be performed when specied
to ensure that the product remains within its original manufacturing specication.
WARNING: The points on this checklist are the minimum the manufacturer recommends. In some
cases more frequent inspections should be carried out. Continuing to use this equipment without
conducting regular inspections will seriously compromise the user and resident / patient’s safety.
Preventive maintenance specied in this manual can prevent accidents.
WARNING: Safety related maintenance and authorized service must be carried out by qualied
personnel, fully trained in servicing procedures by ArjoHuntleigh, and equipped with correct tools and
proper documentation, including Parts List and Service Manual. Failure to meet these requirements
could result in personal injuries and / or unsafe equipment.
POINTS TO BE INSPECTED BY
USER / SERVICE TECHNICIAN
FREQUENCY
Annually or 3000 cycles
Before every use
Initially   
Inspect for evidence of external damage or missing parts.  
Make sure that the activation stations are clean. 
Make sure that the gate stoppers are fully deployed, indicating that the gate is closed. 
No beeping sound from motor box. 
Annual Inspection by an Authorized Technician
The KWIKtrakGate system must be inspected by a qualied ArjoHuntleigh technician on an
annual basis to ensure the proper functioning of its components, as well as the safety of the
patients and care givers that use the equipment. Please contact your local representative to make
arrangements.
NOTE: If the product does not work as intended, immediately contact your local ArjoHuntleigh
representative for support.
Cleaning
To clean the KWIKtrakGate system, wipe it down with a damp cloth using warm water and a
disinfectant cleaner.
Do not use phenol, chlorine or any other type of solvent that may damage the nish.
Troubleshooting
In the event the gate system is malfunctioning, check for the following:
• Make sure the ceiling lift unit is on. The power status LED must be illuminated;
• the tracks are aligned when the gate needs to be operated;
• the lift unit is not resting against the gate stopper;
• the contact blades on the ceiling lift unit making good contact with the activation station
when trying to lock or unlock the gate system.
If the gate system still fails to function properly after all these checks, or if the gate emits a beeping
sound, contact your local ArjoHuntleigh representative for assistance.

001-11502-EN rev. 6
Technical Specications 9
Technical Specications
PRODUCT INFORMATION KWIKtrakGate SYSTEM
Total weight 7 kg (15.4 lb)
Max. safe working load 272 kg (600 lb)
ELECTRICAL
Degree of protection (IP code) IP21
Rating 24 VDC, 5 A max.
Duty cycle 10% (6 min./hour), max. 1 min continuously
Sound power level (dBA) <65 dBA
The KWIKtrakGate meets the requirements of Electromagnetic Compatibility (EMC)
as stated in clause 12.5 of the Medical Devices Directive 93 / 42 / EEC.
The KWIKtrakGate system is compliant with CAN/CSA C22.2 No. 601.1 (SUP1+AM2), UL 60601 1, CAN/
CSA-C22.2 No. 60601-1-08, ANSI/AAMI ES60601-1:2005, and designed according to ISO 10535: 2006.
WARNING: Wireless communications equipment such as wireless home network devices,
mobile phones, cordless telephones and their base stations, walkie-talkies, etc. can affect the
KWIKtrakGate system and should be kept at least 2.3 m away from it. Cables from potentially
strong sources of electromagnetic elds should not be placed near the unit.
ENVIRONMENTAL CONDITIONS
Ambient temperature range Operation: 5° to 40°C (+41 to +104 °F)
Storage: - 25 to 40°C (-13 to 104°F)
Relative humidity range Operation: 15 to 93% non-condensing
Storage: < 94%, non condensing
Atmospheric pressure range Operation: 700 hPa to 1060 hPa (2000 m max)
Storage: 500 hPa to 1060 hPa
WARNING: Product is not suitable in the presence of ammable
anaesthetic mixture with air or oxygen, or with nitrous oxide.
RECYCLING
Package Cardboard recycleable
Gate system Separated and recycled, according to the European Directive
2002/96/EG (WEEE).

001-11502-EN rev. 6
Product Dimensions10
Dimensions
Fig. 5
Track “B”
Track “A”
Product Dimensions
Tracks Height
A B
H90 H90 200 mm
H90 H140 253 mm
H90 H180 293 mm
H140 H140 306 mm
H140 H180 346 mm
H180 H180 386 mm
Electromagnetic Compatibility

001-11502-EN rev. 6
Electromagnetic Compatibility 11
Electromagnetic Compliance
The KWIKtrakGate has been tested for compliance with current regulatory standards regarding
its capacity to block EMI (electromagnetic interference) from external sources.
Nonetheless, some procedures can help reduce electromagnetic interferences:
• Use only ArjoHuntleigh cables and spare parts to avoid increased emissions or
decreased immunity which can compromise the correct functioning of the equipment.
• Ensure that other devices in patient-monitoring and / or life-support areas comply to
accepted emissions standards.
• Maximize the distance between electro-medical devices. High-powered devices may
produce EMI that can affect the ceiling lift. Refer to separation distance table further on in
this document.
For more information on how to manage the unit’s RF electromagnetic environment, please
consult the AMI TIR 18-1997 - Guidance on Electromagnetic Compatibility of Medical Devices for
Clinical / Biomedical Engineers.
Electromagnetic Emissions
Guidance and Manufacturer’s Declaration -
Electromagnetic Emissions - For all Equipment and Systems
The KWIKtrakGate is intended for use in the electromagnetic environment indicated below. The
customer or the user of the KWIKtrakGate should assure that it is used in such an environment.
Emissions test Compliance Electromagnetic environment - guidance
RF emissions
CISPR 11 Group 1
The KWIKtrakGate uses RF energy only for its internal
function. Therefore, its RF emissions are very low and are
not likely to cause any interference in nearby electronic
equipment.
RF emissions
CISPR 11
IEC 61000-3-2
Class B
The KWIKtrakGate is suitable for use in all
establishments, including domestic establishments and
those directly connected to the public low-voltage power
supply network that supplies buildings used for domestic
purposes.
Harmonic
emissions Not applicable
Voltage
uctuations / icker
emissions
IEC 61000-3-3
Not applicable
Electromagnetic Compatibility

001-11502-EN rev. 6
Electromagnetic Compatibility12
Electromagnetic Immunity
Guidance and Manufacturer’s Declaration -
Electromagnetic Immunity - For all Equipment and Systems
The KWIKtrakGate is intended for use in electromagnetic environment specied below. The
customer or the user of the KWIKtrakGate should assure that it is used in such an environment.
Immunity test IEC 60601 test
level Compliance level Electromagnetic environment - guidance
Electrostatic
discharge
(ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete or
ceramic tile. If oors are covered with
synthetic material, the relative
humidity should be at least 30%.
Electrical fast
transient / burst
IEC 61000-4-4
±2 kV for power
supply lines
±1 kV for
input / output lines
±2 kV for power
supply lines
Not applicable
for input/output
lines
Mains power quality should be that
of a typical commercial or hospital
environment.
Surge
IEC 61000-4-5
±1 kV differential
mode
±2 kV for
input / output
Not applicable
Mains power quality should be that
of a typical commercial or hospital
environment.
Voltage dips,
short
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
<5% UT
(>95% dip in UT)
for 0.5 cycle
40% UT
(60% dip in UT) for
5 cycles
70% UT
(30% dip in UT) for
25 cycles
<5% UT
(>95% dip in UT)
for 5 sec.
Not applicable
Mains power quality should be that
of a typical commercial or hospital
environment. If the user of the
KWIKtrakGate System requires
continued operation during power
mains interruptions, it is
recommended that the
KWIKtrakGate System be powered
from am uninterrupted power supply
or a battery.
Power
frequency
(50 / 60 Hz)
magnetic eld
3 A / m 3 A/m
Power frequency magnetic elds
should be at levels characteristic of a
typical location in a typical
commercials or hospital
environment.
NOTE: UT is the AC mains voltage prior to application of the test level.

001-11502-EN rev. 6
Electromagnetic Compatibility 13
(continued)
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity -
For Equipment and Systems that are Not Life-Supporting
Immunity test IEC 60601
test level Compliance level Electromagnetic environment - guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to
80 Mhz
3 V / m
80 MHz to
2.5 GHz
10 Vrms
150 kHz to 80
Mhz
10 V/m
80 MHz to 2.5
GHz
Portable and mobile RF communications
equipment should be used no closer to any
part of the KWIKtrakGate including cables,
than the recommended separation distance
calculated from the equation applicable to the
frequency of the transmitter.
Recommended separation distance
150 KHz to 80 MHz
80 MHz to 800 MHz
800 MHz to 2.5 GHz
where P is the maximum output power rating of
the transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in meters.
Field strengths from xed RF transmitters, as
determined by an electromagnetic site survey,
(a) should be less than the compliance level in
each frequency range. (b)
Interference may occur in the vicinity of
equipment marked with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: Theses guidelines may not apply in all situations. Electromagnetic propagation if
affected by absorption and reection from structures, objects and people.
(a) Field strengths from xed transmitters, such as base stations for radio (cellular / cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to xed RF transmitters, an electromagnetic site survey should be
considered. If the measured eld strength in the location in which the KWIKtrakGate is used
exceeds the applicable RF compliance level above, the KWIKtrakGate should be observed to
verify normal operation. If abnormal performance is observed, additional measures may be
necessary, such as reorienting or relocating the KWIKtrakGate
(b) Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V / m.

001-11502-EN rev. 6
Electromagnetic Compatibility14
(continued)
Recommended Separation Distance Between -
Portable and Mobile RF Communications Equipment and the KWIKtrakGate for
Equipment and Systems that are not Life-Supporting
Recommended separation distances between portable and mobile RF communications
equipment and the KWIKtrakGate
The KWIKtrakGate is intended for use in electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the KWIKtrakGate can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile
RF communication equipment (transmitters) and the KWIKtrakGate as recommended below,
according to the maximum output power of the communications equipment.
Rated maximum
output power of
transmitter
W
Separation distances according to frequency of transmitter m
150 KHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in metres (m) can be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W) according
to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range
applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reection from structures, objects and people.
Electromagnetic Immunity

AUSTRALIA
ArjoHuntleigh Pty Ltd
78, Forsyth street
O’Connor
AU-6163 Western Australia
Tel: [phone]
Free: [phone]
Fax: + 61 89337 9077
BELGIQUE / BELGIË
ArjoHuntleigh NV/SA
Evenbroekveld 16
B-9420 ERPE-MERE
Tél/Tel: [phone]
Fax: [phone]
E-mail: [email protected]
CANADA
ArjoHuntleigh
90 Matheson Boulevard West
Suite 300
MISSISSAUGA, ON, L5R 3R3
Tel/Tél: [phone]
Free: [phone] Institutional
Free: [phone] Home Care
Fax: [phone]
E-mail: [email protected]
ČESKÁ REPUBLIKA
ArjoHuntleigh s.r.o.
Hlinky 118
CZ- 603 00 BRNO
Tel: [phone]
Fax: [phone]
DANMARK
ArjoHuntleigh A/S
Vassingerødvej 52
DK-3540 LYNGE
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
DEUTSCHLAND
ArjoHuntleigh GmbH
Peter-Sander-Strasse 10
D-55252 MAINZ-KASTEL
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
ΕΛΛΑ∆Α
C. Psimitis Co Ltd
Dimitriou Andr. 59
GR-16121 KAISARIANI ATTIKIS
Τηλ: 21 0724 36 68
Φάξ: 21 0721 55 53
ESPAÑA
ArjoHuntleigh Ibérica S.L.
Ctra. de Rubí, 88 1ª planta - A1
08173 Sant Cugat del Vallés
ES- BARCELONA 08173
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
FAR EAST
ARJO Far East Limited
Unit 3A, 4/F., block B Hoi Luen
Industrial Centre
55 Hoi Yuen Road,
Kwun Tong, Kowloon
HONG KONG
Tel: [phone]
Fax: [phone]
FRANCE
ArjoHuntleigh SAS
2 Avenue Alcide de Gasperi
CS 70133
59436 RONCQ CEDEX
Tél: [phone]
Fax: [phone]
E-mail : [email protected]
INTERNATIONAL
ArjoHuntleigh International Ltd.
ArjoHuntleigh House
Houghton Hall Park
Houghton Regis
UK-DUNSTABLE LU5 5XF
Tel: [phone]
Fax: [phone]
E-mail:
[e-mail]
ITALIA
ArjoHuntleigh S.p.A.
Via di Tor Vergata 432
00133 ROMA - ITALIA
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
NEDERLAND
ArjoHuntleigh Nederland BV
Biezenwei 21
4004 MB TIEL
Postbus 6116
4000 HC TIEL
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
NEW ZEALAND
ArjoHuntleigh Ltd
41 Vestey Drive
Mount Wellington
AUCKLAND 1060
Tel: [phone]
Free Call: 0800 000 151
Fax: [phone]
E-mail: [email protected]
NORGE
ArjoHuntleigh Norway AS
Ryenstubben 2
NO-0679 OSLO
Tel: [phone]
Faks: [phone]
E-mail: [email protected]
POLSKA
ArjoHuntleigh Polska Sp. z o.o.
ul. Ks Piotra Wawrzyniaka 2
PL 62-052 KOMORNIKI (Poznan)
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
PORTUGAL
ArjoHuntleigh em Portugal:
MAQUET Portugal, Lda. (Distribudor Exclusivo)
Rua Poeta Bocage n.º 2 - 2G
1600-233 Lisboa, Portugal
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
SUISSE / SCHWEIZ
ArjoHuntleigh AG
Fabrikstrasse 8
Postfach
4614 Hägendorf,
Tél/Tel: [phone]
Fax: [phone]
SUOMI
ArjoHuntleigh OY
Vanha Porvoontie 229
FI-01380 VANTAA
Puh: [phone]
Faksi: [phone]
SVERIGE
ARJO Scandinavia AB
Verkstadsvägen 5
Box 61
SE-241 21 ESLÖV
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
UNITED KINGDOM
ArjoHuntleigh UK
ArjoHuntleigh House
Houghton Hall Park
Houghton Regis
UK-DUNSTABLE LU5 5XF
Tel: [phone]
Fax: [phone]
E-mail:
[email protected]
USA
ArjoHuntleigh Inc.
2349 W Lake Street Suite 250
Addison, IL 60101
Tel: [phone]
Free: [phone] Institutional
Free: [phone] Home Care
Fax: [phone]
E-mail: [email protected]
ÖSTERREICH
ArjoHuntleigh GmbH
Dörrstrasse 85
AT-6020 INNSBRUCK
Tel: [phone]
Fax: [phone]
www.arjohuntleigh.com

www.ArjoHuntleigh.com
GETINGE GROUP is a leading global provider of products and systems that
contribute to quality enhancement and cost efficiency within healthcare and life
sciences. We operate under the three brands of ArjoHuntleigh, GETINGE and
MAQUET. ArjoHuntleigh focuses on patient mobility and wound management
solutions. GETINGE provides solutions for infection control within healthcare and
contamination prevention within life sciences. MAQUET specializes in solutions,
therapies and products for surgical interventions and intensive care.
ArjoHuntleigh AB
Verkstadsvägen 5
241 38 Eslöv
SWEDEN