Arlight V1-S User manual

User Manual Ver 1.0.4
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Technical Parameters
Output power 180W/360W/540W/720W
(12V/24V/36V/48V)
Output voltage 12-48VDC
Output current 1CH,15A
Input and Output
Input voltage 12-48VDC
Input current 15A
Safety and EMC
EMC standard (EMC) EN301 489,EN 62479
Certification CE,EMC,LVD
EN60950
Safety standard(LVD)
Output type Constant voltage
Warranty and Protection
5 years
Protection
Reverse polarity
Warranty
Ta: -30
O
C ~ +55
O
C
T c:
+85
O
C
LVD
Model No.: V1-S
Constant Voltage Triac Dimmer
1 Channel/Constant voltage /Logarithmic dimmingcurve/AC Push-Dim /Triac dimming
Features
● Triac dimming, input AC40V-220V dimming signal.
● Apply to leading edge/trailing edge Triac dimmers and dimming system.
● One channel PWM constant voltage output, output current 15A max.
● PWM digital dimming, logarithmic dimming curve.
● Over current protection, short circuit protection, over temperature protection.
● Connect with external AC push switch to achieve on/off and dimming function.
V1-S Constant Voltage Triac Dimmer
Page 1
Mechanical Structures and Installations
Wiring Diagram
AC100-240V Power Supply
12-48VDC
Constant Voltage
27mm
175mm
160mm
45mm
Triac dimmer AC L input
AC Push switch L input
Power input -
Power input +
LED output +
AC Push switch N input
Triac dimmer AC N input
LED indicator
LED output -
Single color LED strip
+
Dimming data
Dimming range
40-220VAC + AC Push-Dim
0 -100%
Input signal
Dimming curve Logarithmic
500Hz (default)
PWM Frequency
Installation rack
Over current
Short circuit
Over temperature
AC PUSH
SWITCH
A1
A2
TRIAC DIMMER IN
40~220VAC
LED OUT
INPUT
12-48VDC
Potentiometer
2. Connect Triac dimmer with neutral wire input
1. Connect single wire Triac dimmer without neutral wire
L
N
AC PUSH
SWITCH
A1
A2
TRIAC DIMMER IN
40~220VAC
LED OUT
INPUT
12-48VDC
AC100-240V Power Supply
12-48VDC
Constant Voltage
Single color LED strip
+
L
N
AC PUSH
SWITCH
A1
A2
TRIAC DIMMER IN
40~220VAC
LED OUT
INPUT
12-48VDC
Weight
0.106kg
Gross weight
Net weight
0.126kg
Before connecting the Triac dimmer, look at the input of the dimmer for a neutral line.
Please select the appropriate wiring method according to the type of Triac dimmer.

User Manual Ver 1.0.4 Page 2
Dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.6
AC Push-Dim Function
● Short press:
Turn on or off light.
● Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes to the opposite direction.
● Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.
● Synchronization:
If more than one controller are connected to the same push switch, do a long press for more than 10s,
then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of controllers connected to a push switch does not exceed 25 pieces,
The maximum length of the wires from push to controller should be no more than 20 meters.
The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching
(momentary) wall switchs.
● Connect with AC push switch
AC100-240V Power Supply
12-48VDC
Constant Voltage
Single color LED strip
+
L
N
AC PUSH
SWITCH
A1
A2
TRIAC DIMMER IN
40~220VAC
LED OUT
INPUT
12-48VDC
AC100-240V Power Supply
12-48VDC
Constant Voltage
Single color LED strip
+
AC PUSH
SWITCH
A1
A2
TRIAC DIMMER IN
40~220VAC
LED OUT
INPUT
12-48VDC
Triac Dimming Input
● AC40V-220V dimming signal input can get 0%-100% brightness output, and the brightness is proportional to
the input dimming signal. If the brightness can not go to 0% or 100%, please check the input voltage whether can
get to the lowest or highest voltage.
● While connected with a Triac dimmer, such as Lutrom, Clipsal, Dynalite dimmer, different Triac dimmers from different
suppliers may have different minimum dimming levels which the driver can not be dimmed below. To dim to 1%,
please make sure the dimmer supports 1% minimum dimming level.
● The product adopt analog method detect dimming signal input, adjust brightness consistency between different Triac
dimmer through potentiometer.
● The Triac dimmer or Push switch can be connected at the same time, which makes the product more user-friendly and
more options to fit for some extra-ordinary demands.
● If the product be used with the Push-Dim interface prior to using the Triac interface, the Triac dimming signal should
change over 10% to return Triac control.
V1-S Constant Voltage Triac Dimmer
Push Switch