Armacost Lighting AL-RGB4A User manual

21 Color RGB LED Lighting Controller
Model # AL-RGB4A
This low voltage DC color controller is an easy-to-use, 3-channel,
preprogrammed RGB LED light mixer designed to change the colors of
RibbonFlex Pro®Custom Color RGB LED Tape Lighting. It will also work
with other 3-channel 12 or 24V DC RGB tape light strips and modules.
Suitable for RV and boat interior applications (dry location only), this
device can be direct wired to an on-board 12-24V battery.
FEATURES
 21 preprogrammed static colors, including shades of white
 4 dynamic color-changing effects
 Brightness adjustable for static colors
 Speed adjustable for color-changing effects
 Built-in memory, unit will remember last color after powered off
 Remote control (infrared, must aim remote at controller)
INSTALLATION GUIDELINES
CAUTION: Do not connect to 120V AC current.
For use only with low voltage 12 or 24 volt RGB LED lighting.
For dry location only.
IMPORTANT
Wire runs inside walls must be installed in accordance with the National
Electrical Code, low voltage Class 2 circuit. Use properly certified CL2
or better cabling. Do not install low-voltage wiring in the same wire run
as AC power. If AC and low-voltage wires cross, keep them at 90-degree
angles. If you are unclear as to how to install and wire this device, contact
a qualified electrician.
 Use only insulated staples, plastic ties or clips to secure wires.
 Route and secure wires so they will not be pinched or damaged.
 For longer life and better color-changing performance, keep voltage drop
to a minimum (see Understanding voltage drop).
 Failure to observe polarity or shorting of wires may damage the controller
and LED lights.
 Know your LED wattage requirements. Read and follow instructions for
watts required and length limitations of your RGB LED lighting.
CONNECTIONS
RGB LED Tape Lighting
+
R
G
B
Power Supply
+
–
DC Out
AC120V
RGB LED
Controller
+
–
+
R
G
B
RGB LED Tape Lighting
+
R
G
B
Visit armacostlighting.com for RGB LED wiring diagrams and an online
voltage-drop calculator.
Maintain polarity for correct color sequencing
The 2-conductor red/black wire connects to the low voltage output of your
power supply. Red connects to positive, black to negative.
The 4-conductor RGB flat ribbon wire connects to the RGB LED lighting.
Be sure red connects to red, green to green, blue to blue. The white
wire from the controller always connects to the + (positive) indicator
or + wire on your LED light. Note: The positive wire on your RGB
LED light strip will be either a black or white wire depending on the
manufacturers’ configuration.

OPERATION Understanding voltage drop
Voltage drop is a natural occurrence in all low voltage lighting systems.
It is the gradual decrease in voltage that occurs along the length of your
DC power feed wires to your LED lighting. It is a function of wire length,
wire thickness, and the total watts used by your LED lighting.
With longer lengths of RGB LED tape lighting, voltage drop also occurs
within the tape light. Voltage drop only becomes undesirable if you notice
the light color or brightness in one area of your lighting is objectionably
different than another area.
As a practical approach to installing your RGB LED tape light, test your
lighting prior to final installation. If voltage drop appears to be a concern,
use shorter lengths of power feed wires, switch to a heavier gauge wire
(lower AWG number), or shorten the length of your LED tape lighting.
SPECIFICATIONS
Input voltage..........................................................................................12-24V DC
Output............................................................................................. 3 channel RGB
Maximum load............................................................................4 amps per channel
Static power consumption ........................................................................... < 1 watt
Working temperature............................................................... -4~140°F (-20~60°C)
Infrared remote ............................................................... Battery, coin style CR2025
Ratings............................................................................................CE, RoHS, CSA
Control the speed of the
color-changing effect.
Press MODE button to cycle to next
static color (21 colors in all), then to
four (4) color-changing effects.
TROUBLESHOOTING
Limited colors displaying?
Check to be sure all RGB connections are secure
No color-changing effects?
Increase effects speed on controller or cycle through mode to the effects
Uneven brightness?
Shorten length of lighting, reduce the length of RGB power wire or use
thicker wires or an RGB signal amplifier (see Understanding voltage drop)
Remote not working?
Point remote at controller, move closer to controller or replace battery
(CR2025)
For additional RGB color controllers, RGB
signal amplifiers, and LED tape lighting and
accessories, visit armacostlighting.com.
Limited 2-year warranty. This product is for dry location use only. Failure to use this
device for its intended purpose or improper installation will void warranty. Questions?
Email [email protected].
Control the
brightness level.
Displays the color mixture
signal being delivered to
the RGB LED lights.
© 2014 Armacost Lighting. All rights reserved.
REV 10.13
Colors
1. Cool Bright White
2. Golden White
3. Red
4. Blue
5. Dark Purple
6. Emerald Green
7. Lime Green
8. Ice Blue
9. Orange
10. Turquoise
11. Arctic Blue
12. Champagne White
13. Yellow
14. Sky Blue
15. Purple
16. Light Purple
17. Lime Yellow
18. Hot Pink
19. Purple White
20. Sea Foam
21. Pale Blue-White
Color-Changing Effects
1. Quick change flash:
Red, Green, Blue
2. Seven color quick change:
Red, Green, Yellow, Blue,
Purple, Teal, White
3. Red, Green, Blue Cross Fade
4. Seven color dissolve: Red,
Yellow, Green, Blue, Teal,
Purple, White
COLORS AND EFFECTS