Armacost Lighting Proline 713420 User manual

Proline RGB Color LED Controller
With RF Remote Control
Model # 713420
Introduction
This LED controller is designed to drive constant voltage
RGB LED products such as LED tape light or LED
fixtures in a voltage range of 5–24 volts DC. The receiver
works with the RF wireless remote control, which allows
the user to choose between multiple colors, adjust
the LED brightness, and select dynamic effects.
Receiver & wiring
24mm
72mm
87mm
123
1. Input – from power supply
The controller input and output voltage range is
5–24 volts DC. Make sure the LED lighting voltage is
within this range and below the rated wattage of the
power supply. Connect input wires from the power
supply to the controller as indicated by the polarity
markings on the controller (+ to + and – to –).
2. Output – to LED lighting
Observe polarity indicated on the controller
when connecting to LED lighting (+ to +,
G to G, R to R, and B to B).
Make sure the voltage of the LED lighting is the
same as the power supply and the maximum
load doesn’t exceed that of the controller.
CAUTION: Shorting of output cables could cause
permanent damage to controller. Make sure
cables are well insulated from each other.
3. Controller status indicator
This light shows the controller status as follows:
Steady green: Normal working mode
Single green blink: Command received
Long single green blink: Mode or color cycle limit reached
Long single yellow blink: Brightness or speed limit reached
Red flash: Overload protection
Yellow flash: Overheat protection
Green flash 3 times: New remote control paired
4. Wiring diagram
Connect the power supply to the controller input
and the controller output to the LED lighting.
The output voltage of the power supply must
be the same as the voltage of the LED lighting.
Make sure all power cables are conected
securely and insulated before powering on.
LED
Controller
5–24V DC
Output
Power Supply
5–24V DC 5–24V DC
100/230V
AC Power
LED
Lighting
Remote Control
7
6
58
5. On / Off
Press the “|” key to turn on controller or the “0”
key to turn off. The controller will remember
the controller state when powered off, and will
return to that state when powered back on.
6. RGB color setting
Press the “COLOR+” and “COLOR–” keys to
scroll through all the color options. The colored
keys are shortcuts for preset colors. Press the
and the keys to adjust color brightness.
1
2 3
Compact
Size
Wide Voltage
Range
High
Power
Full Safety
Protection
Wireless
Remote

7. Dynamic effects
Press “MODE+” and “MODE–” to select the
dynamic effect mode and “SPEED+” and
“SPEED–” to adjust the effect speed.
Press the “DEMO” key to play the dynamic effects.
8. Remote indicator
When pressing keys, the indicator blinks if the remote
is working properly. If the indicator flashes slowly
when pressing keys, battery power is low and it needs
to be replaced. Replace with a CR2032 battery.
Remote control operation
9. Using the remote control
Pull out plastic battery insulation tab before use.
The RF wireless remote will work through walls
and doors. Do not install in a metal enclosure.
10. Pairing with a new remote control
The remote control and receiver are already paired,
but up to 5 remotes can be paired to one receiver.
To pair a new remote:
1. Disconnect power to receiver
and wait five seconds.
2. Reconnect power and wait ten seconds.
3. Press the “SPEED–” and “SPEED+” keys
simultaneously for about three seconds
until the remote indicator flashes quickly.
11. De-pairing remotes
To de-pair a remote control, pair the remote you
wish to continue using with the controller and
any other paired remotes will be de-paired.
Safety Protection
The controller has a function to prevent it from
being damaged by mis-wiring, output short circuit,
overloading, or overheating. It will automatically
shut down under these extreme conditions until
safe operating conditions are restored. To avoid
shutdowns, make sure the installed LED lighting is
compatible with constant voltage driving, is in the
rated range of the controller, and the cables are well
connected and insulated. Also, install the controller
with proper ventilation and heat dissipation in mind.
Customer support
Email: [email protected]
Phone: [phone]
Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
Limited 1-year warranty. This product is for dry
location use only. Improper installation, improper
powering, abuse, or failure to use this device for
its intended purpose will void warranty. Proof of
purchase is required for all returns. Questions?
Email [email protected].
Specifications
Output mode..........................PWM constant voltage
Working voltage .......................................5–24V DC
Rated output current.......................3x4A (12A max)
Brightness levels ................................................. 5
Static colors...................................................... 30
Dynamic effects................................................. 34
Dynamic speed levels......................................... 10
Color preset keys ................................................. 7
PWM physical grade............................... 4000 steps
Overload protection............................................Yes
Overheat protection............................................Yes
Remote frequency.................................433.92MHz
Remote control range ....... >49 ft./15m in open areas
Controller dimensions .......... 3.43 X 0.95 X 0.59 in./
................................................... 87 X 24 X 15mm
Remote dimensions ........... 3.41 X 1.42 X 0.329 in./
............................................... 86.5 X 36 X 7.5mm
4 5
© 2020 Armacost Lighting. All rights reserved. 201001
armacostlighting.com