Armacost Lighting ProLine 513115 User manual

ProLine Single Color LED Controller
With RF Remote Control
Model # 513115
Introduction
This LED controller is designed to drive constant
voltage single color LED products such as LED tape
light or LED fixtures in a voltage range of 5–24
volts DC. The receiver works with the RF wireless
remote control, which allows the user to adjust LED
brightness.
Receiver & wiring
24mm
72mm
87mm
123
1. Input – from power supply
The controller input and output voltage range is
5–24 volts DC. Make sure the LED lighting voltage is
within this range and below the rated wattage of the
power supply. Connect input wires from the power
supply to the controller as indicated by the polarity
markings on the controller (+ to + and – to –).
2. Output – to LED lighting
Observe polarity indicated on the controller when
connecting to LED lighting (+ to + and – to –).
Make sure the voltage of the LED lighting is the
same as the power supply and the maximum
load doesn’t exceed that of the controller.
CAUTION: Shorting of output cables could cause
permanent damage to controller. Make sure
cables are well insulated from each other.
3. Status indicator
This light shows the working status of the
controller. It shows different events as following:
Steady green: Normal operation
Single green blink: Command received.
Long single green blink: Mode or color cycle edge.
Long single yellow blink: Reach brightness limit.
Red flash: Overload protection.
Yellow flash: Over heat protection.
Green flash 3 times: New remote controller paired.
Wiring diagram
Connect the power supply to the controller input
and the controller output to the LED lighting.
The output voltage of the power supply must
be the same as the voltage of the LED lighting.
Make sure all power cables are conected
securely and insulated before powering on.
Remote
Control
LED
Controller
5–24V DC
Output
Power Supply
5–24V DC 5–24V DC
100/230V
AC Power
LED
Lighting
1
2 3
Wireless Remote
Built-in Safety Protection
Wide Voltage Range
High Power
Compact Size

Remote Control
6
5
4
7
4. On/Off
Press this key to turn on controller. Press and
hold to turn off. The controller will remember
the controller state when powered off, and will
return to that state when powered back on.
5/6. Brightness adjustment
Press the “▲” and “▼” keys to adjust brightness.
7. Remote indicator
When pressing keys, the indicator blinks if the remote
is working properly. If the indicator flashes slowly
when pressing keys, battery power is low and it needs
to be replaced. Replace with a CR2032 battery.
Remote control operation
8. Using the remote control
Pull out plastic battery insulation tab before use.
The RF wireless remote will work through non-metal
walls and doors. Do not install in a metal enclosure.
9. Pairing with a new remote control
The remote control and receiver are already paired,
but up to 5 remotes can be paired to one receiver.
To pair a new remote:
1. Disconnect power to receiver
and wait five seconds.
2. Reconnect power.
3. Within ten seconds, press the ON/OFF
and “▼” keys simultaneously
for about three seconds.
10. De-pairing remotes
To de-pair a remote control, pair the remote you
wish to continue using with the controller and
any other paired remotes will be de-paired.
Safety protection
The controller has built-in protection for incorrect
wiring, output short circuiting, overloading and
overheating. If the any of these conditions occurs,
the receiver will automatically shut down until
the issue is corrected. If this occurs, check
to make sure the connected LED lighting is
rated for constant voltage current and is in the
controller’s voltage output range. Also, make sure
all cables are securely connected and insulated,
and that the receiver is well ventilated.
Specifications
Output mode..........................PWM constant voltage
Working voltage .......................................5–24V DC
Rated output current.....................................1x10A
Brightness grade....................................... 11 levels
PWM grade ...........................................4000 steps
Overload protection............................................Yes
Overheat protection............................................Yes
Remote frequency.................................433.92MHz
Remote control range ....... >49 ft./15m in open areas
Controller dimensions .......... 1.97 X 0.59 X 0.28 in./
................................................ 87 X 24 X 14.5mm
4 5
Customer support
Email: [email protected]
Phone: [phone]
Monday–Friday, 9 a.m.–5 p.m., ET
Three-year limited warranty
This product is for dry location use only. Improper
installation, improper powering, abuse, or failure
to use this device for its intended purpose will void
warranty. Proof of purchase is required for all returns.
Questions? Email [email protected].
© 2021 Armacost Lighting. All rights reserved. 210601
armacostlighting.com