Armstrong 11AV User manual

Free Floating Lever Air/Gas Vents
Models 11AV, 22AV and 13AV
Installation and Operation Manual
46-C

Installation Procedures.............3
Troubleshooting......................4
Technical Data Charts...............5
Warning: This bullen should be used by experienced personnel as a guide to the installaon and
maintenance of the Armstrong Air/Gas Vents. Selecon or installaon of equipment should always be
accompanied by competent technical assistance. We encourage you to contact Armstrong or your local
representave if further informaon is required.
Overview
©2011 Armstrong International, Inc. Designs, materials, weights and performance ratings are approximate and
subject to change without notice.

Installation Procedures
Install air vents at all the high points on liquid service systems, hydronic systems, or any liquid storage or distribution
system. See Figures 1, 2 & 3 for typical installations.
3
Do not exceed the maximum allowable pressure noted on the label on the side of the air vent
body. Also, check to see if the air/gas vent has the proper maximum differential pressure for your
particular application.
When tightening a pipe into either the inlet or outlet fittings of an 11AV, 22AV or 13AV use only the
hex-shaped fittings as wrenching surfaces. Do not use other parts of the vent for wrenching as
unnecessary stress may be placed on the vent body.
Before installing the vent, flush out the line to remove loose dirt. Use pipe dope or teflon tape
sparingly and on male threads only. Leave the end thread exposed to avoid introducing sealant into the
system.
The inlet and outlet piping should be the same size as the air vent connections. Do not reduce the size
of the inlet on light loads; however, smaller pipe or tubing may be used on the outlet. Keep the piping
as short as possible, with a minimum of valves and fittings. If you are installing an air vent without
an equalizing connection, do not use elbows in the inlet line from the equipment to the vent.
Install gate valves or full ported ball valves (Do Not Use Globe Valves) so the air vent can be isolated
from the system to permit servicing. If the air vent is installed in a closed piping arrangement, install a
union on each side of the air vent.
Be certain the vent is installed properly. Note the direction of flow arrow on the label and the red
label indicating UP for air and gas venting service.
Do Not use a pipeline strainer in the line leading to the vent.
Air vents should be installed so that they can be checked periodically. A drain line should be piped to
a floor drain or to a visible location where it can be regularly checked for leakage.
Caution: Do not install air vents with an open discharge where a malfunction could cause damage
i.e. above false ceilings.
1
2
3
4
5
6
7
8
11AV Air Vent
To Drain
Ball Valve
Return
High Point on Main
13AV Air Vent
A
B
22AV Air Vent
To Drain
Flow
Figure l. Installation of Model
11AV automatic air vent on high
point of main.
Figure 2. Installation of a Model 22AV
automatic air vent on loop in piping.
Figure 3. Continuous venting using
a Model 13AV with an equalizing
line where large amounts of air
must be vented. As air enters line
A, water leaves through line B.

Troubleshooting
Check operation. It is normal on hydronic systems to have no discharge from the vent, but this is not proof that
the vent is functioning properly. To check the air vent, disconnect the outlet piping and observe the discharge from
the unit. If the vent is working correctly, a little air should escape, followed by a small amount
of liquid.
When an 11AV, 22AV or 13AV is not operating properly, remove it from service and force water or air through the
discharge fitting. Back-flushing to remove scale and dirt often restores the air vent to its normal operating condition.
When an 11AV, 22AV or 13AV cannot be made to operate properly, replace it with a new one having the same orifice
size.
4
For assistance with an unsual installation or service problems, contact your Armstrong Representative or Armstrong International’s Application
Engineering Department
On new installations, an air vent may fail to open if the maximum operating pressure on the label is less than the
actual pressure being encountered. If this is the case, replace the air/gas vent with one sized properly for your higher
maximum operating pressure. Consult your Armstrong Representative.
An unusual increase in system pressure may cause the air vent to lock shut. Either eliminate the cause of the
increased pressure or replace the air vent with one that can handle the peak pressures.

Free Floating Lever Air/Gas Vents - All Stainless Steel
Models 11AV, 22AV and 13AV
5
Maximum Operating Pressures of free floating lever vents with weighted floats for different orifice sizes, and the specific gravities on which they can be used.
11-AV Maximum Operating Pressures
Minimum Specific Gravity 0.75 0.50
Float wt., oz (g) 2.90 (82) Standard 2.08 (59) Special
Orifice Size (in) Maximum Operating Pressure
psi bar psi bar
1/8 178 12 118 8
#38 267 18 177 12
5/64 400 28 311 21
22-AV Maximum Operating Pressure
Specific Gravity* 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50
Float wt., oz (g) 10.0 (282) 9.5 (268) 9.0 (254) 8.5 (240) .0 (226) 7.5 (212) 5.4 (152) 5.0 (141) 4.6 (130) 4.2 (119) 3.8 (109)
Orifice Size (in) Maximum Operating Pressure
psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar
5/16 35 2.4 33 2.3 31 2.2 30 2.0 28 1.9 26 1.8 19 1.3 18 1.2 16 1.1 15 1.0 14 0.9
1/4 57 3.9 54 3.7 51 3.5 49 3.4 46 3.2 43 3.0 31 2.1 29 2.0 27 1.8 24 1.7 22 1.5
3/16 126 8.7 120 8.2 113 7.8 107 7.4 101 7.0 95 6.5 68 4.7 64 4.4 59 4.1 54 3.7 49 3.4
5/32 217 14.9 206 14.2 195 13.5 185 12.7 174 12.0 163 11.2 118 8.1 110 7.6 101 7.0 93 6.4 85 5.8
1/8 371 25.6 352 24.3 334 23.0 316 21.8 297 20.5 279 19.2 202 13.9 187 12.9 173 12.0 159 11.0 145 10.0
7/64 474 32.7 451 31.1 427 29.5 404 27.9 380 26.2 357 24.6 258 17.8 240 16.5 222 15.3 204 14.0 186 12.8
#38 590 40.7 561 38.7 532 36.7 503 34.7 473 32.7 444 30.6 321 22.1 298 20.6 276 19.0 253 17.5 231 15.9
5/64 600 41.4 600 41.4 600 41.4 600 41.4 600 41.4 600 41.4 473 32.6 440 30.3 407 28.1 374 25.8 341 23.5
13-AV Maximum Operating Pressures
Specific Gravity* 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60
Float wt., oz (g) 14.9 (423) 14.2 (402) 13.4 (381) 12.7 (360) 12.0 (339) 11.2 (318) 10.5 (296) 9.7 (275) 9.0 (254)
Orifice Size (in) Maximum Operating Pressure
psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar
1/2 21 1.5 20 1.4 19 1.3 18 1.3 17 1.2 16 1.1 15 1.0 14 1.0 13 0.9
3/8 45 3.1 43 3.0 41 2.8 38 2.7 36 2.5 34 2.3 32 2.2 30 2.0 27 1.9
5/16 72 5.0 69 4.7 65 4.5 61 4.2 58 4.0 54 3.8 51 3.5 47 3.3 44 3.0
9/32 96 6.6 91 6.3 87 6.0 82 5.6 77 5.3 72 5.0 68 4.7 63 4.3 58 4.0
1/4 144 9.9 137 9.4 130 8.9 123 8.5 116 8.0 109 7.5 102 7.0 94 6.5 87 6.0
7/32 206 14 196 13 186 13 176 12 165 11 155 10.7 145 10.0 135 9.3 125 8.6
3/16 309 21 294 20 279 19 264 18 249 17 234 16 218 15 203 14 188 13
5/32 484 33 460 32 437 30 413 28 389 27 365 25 342 24 318 22 294 20
1/8 570 39 570 39 570 39 570 39 570 39 570 39 570 39 570 39 570 39
7/64 570 39 570 39 570 39 570 39 570 39 570 39 570 39 570 39 570 39
*If specific gravity falls between those shown, use next lowest: e.g., if actual gravity is 0.73, use 0.70 specific gravity data.

Armstrong International
816 Maple Street, Three Rivers, MI 49093 – USA Phone: [phone] Fax: [phone]
armstronginternational.com
46-C
Printed in U.S.A. - 11/11
© 2011 Armstrong International, Inc.