Array electronic AG310 Series User manual

Users Manual for Battery Charger
This battery charger is especially made for Tour Guide System
AG310 Series manufactured by Array CO. Ltd, in which there are 24
charging slots are designed especially for Ni-MH or Ni-Cd batteries
charging.
Ⅰ. Product Model: AG310-C.
Ⅱ. Cautions
Please never use batteries which are not Ni-MH and Ni-Cd
Batteries for charging, or it will probably cause the batteries to
leak or even explode.
Please make sure that the Transmitter/ Receiver is turned OFF
before charging.
Please keep the charging case open while charging; it will stop
charging automatically when the case is closed.
Please do not charge repeatedly after the batteries are fully
charged.
Please do not interrupt while charging, or it will affect the
charging result.
Please do not charge when the ambient temperature is above
40℃.
When using the cigarette lighter of an automobile as power
supply for charging, the engine of automobile must keep
running.
Please remove the batteries when the Transmitter/ Receiver is
not used for an extended time.
1.
2.
3.
4.
5.
6.
7.
8.

The fully-charged batteries must be recharged after they haven’ t
been used for more than 4 months.
Ⅲ. Name of Each Part
1. Body of Charger
2. Micro switch
3. Micro switch preventor
4. Power input outlet of the
charger
5. Transmitter/ Receiver
6. Charging indicator LED
7. AC Power Adapter
8. Cigarette lighter cable for
automobile
Ⅳ.Operation Instructions:
9.
2
3
4
1
5
6
7
8
3
1
2
4
AB
B

As shown in Fig.②, plug one end of the adapter into the power
input outlet. Then power on the other end of the adapter as
shown in Fig.①.
If charge in automobile, please plug end A of cigarette lighter
cable into cigarette lighter holder, then plug end B into the
outlet of charger.
As shown in Fig.③, make sure that the transmitter or receiver
is switched OFF.
As shown in Fig.④, put the transmitter or receiver into
charging slot.
Ⅴ. Indications of Charging LED
Self-test:
The LED will be in red, then in green, at last not on the moment
when the power of the charger is switched on.
This process is called self-test.
When the LED is in red, it indicates that the batteries are
charging.
When the LED is in green, it indicates that the batteries are
fully charged.
When the LED doesn’t work, it indicates that the charging
circuit is not closed (See Elimination of Common Faults 1).
When the LED blinks in red and green by turns, it indicates that
the batteries are worn out (See Elimination of Common Faults 2)
When the LED blinks in red, it indicates that charging is not
functioning (See Elimination of Common Faults 3).
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.

Ⅵ. Elimination of Common Faults
ITEM FAULT POSSIBLE
REASON SOLVING METHODS
1The LED
doesn’t work
The charging
circuit
isn't closed
Make sure that the transmitter
or receiver is inserted firmly;
Check if reverse
battery’s electrode is inserted;
Clean the contact piece of the
charging electrodes.
2The LED blinks in red and green
by turns
The batteries are
worn out. Replace the batteries.
3The LED blinks
in red Charging is not functioning
Clean the contact piece of the
charging electrodes;
Make sure that the transmitter
or receiver is inserted firmly.
REMARK: PLEASE SEND IT TO US FOR REPAIRING WHEN
Ⅶ. Technical Data
AC Power Adapter input Voltage wide range 90-264VAC,47-63HZ
AC Power Adapter output Regulation 18.50V-19.95V
AC Power Adapter Ripple/Noise 300mV
AC Power Adapter Max 4.74A
Input voltage of charger 12-32V
Charging current 150~400mA
Number of charging slots 24
Ambient temperature -20℃~40℃
Net weight About 3kg
Dimensions of charger 59cm×38cm×16cm
THE FAULTS CANNOT BE ELIMINATED ON YOUR OWN.