Arthrex Lift-Assist AR-1627 User manual

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 2 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
IMPORTANT NOTICES
READ THESE INSTRUCTIONS COMPLETELY BEFORE USING
THIS PRODUCT.
•Read and understand all warnings in this manual and on the device itself
prior to use with a patient.
•The symbol is intended to alert the user to important procedures or
safety instructions regarding the use of this device.
•The symbol on the labels is intended to show when the IFU should
be referenced for use.
• The techniques detailed in this manual are only manufacturer’s
suggestions. The final responsibility for patient care with respect to this
device remains with the attending physician.
•Device function should be checked prior to each usage.
•This device should only be operated by trained personnel.
•All modifications, upgrades, or repairs must be performed by an
authorized specialist.
•Keep this manual available for future reference.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 3 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
1.0 SAFETY PRECAUTIONS AND GENERAL INFORMATION
1.1 GENERAL SAFETY WARNINGS
•Do not use if product shows visible damage.
•Do not exceed device weight limits.
•Ensure device is securely attached and locked to OR Table accessory rail
before transferring patient.
•Whenever inclining the patient, monitor the head closely to insure that the head
positioner slides freely without obstruction to prevent undue pressure on the
patient’s head and neck.
1.2 TABLE COMPATIBILITY
The Lift-Assist™ Beach Chair is compatible with the following surgical table rail
styles: US, UK, EU, DEN, JP
Note: Refer to the surgical table manufacturer's user guide for instructions on use.
Always refer to the surgical table manufacturer’s weight limits.
NEVER EXCEED THE WEIGHT CAPACITY
OF THE O.R. TABLE

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 4 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
1.3 PRODUCT SPECIFICATIONS
500 lb (227 kg) patient weight limit
61 lb (28 kg) shoulder panel weight limit
0°- 85° articulation range
20” -26” width extension
2.0 COMPONENT IDENTIFICATION
2.1 ® Lift-Assist™ Beach Chair FRONT
Intubation Pad
Shoulder Panels
Rail Clamp Mounts
Intubation Plate
Rail Clamp Knobs

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 5 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
BACK
Head Positioner
Tubes
Head Positioner
Tube Release
Beach Chair
Release Handle
Shoulder Panel Locks
Width Extension
Knob
Pendant Holders
RAIL CLAMP
Top Jaw
Bottom Jaw
(hinged)
Support Bar
Head Positioner
Tube Handle

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 6 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
3.1 PRIOR TO USE
1. Ensure surgical table is in its final operation location with respect to
the room.
2. Ensure the table is locked.
3. Remove X-ray tops and back section pads from the surgical table.
4. Remove or lower the back (PREFERRED) or leg section of the table
by 90°.
5. Loosen both rail clamp mount knobs.
3.2 SET-UP
1. Unlock shoulder panel locks and remove shoulder panels as shown below by
swinging panels back and unhooking from head positioner tubes. This will
make beach chair lighter and easier to manage.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 7 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
2. Place top jaw of the rail clamp onto
the torso (seat) section of the table
rail as shown.
3. Snap hinged bottom jaw onto the
rail.
4. Slide rail clamp to the end of the
table rail. Preferably to rail stops.
5. Repeat steps 2-4 with second rail clamp on opposite side of table.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 8 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
6. Loosen width extension knob by
turning to the left.
7. Fully extend width of the support
bar.
8. Back-out (loosen) rail clamp knobs
completely.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 9 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
9. Lift Beach Chair by placing dominant hand on the red release handle and
opposite hand on the appropriate side as shown. The non-dominant hand
should be placed well behind the rail clamp mount.
10.Align rail clamp mounts above rail clamps.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 10 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
12. Rest rail clamp mount on edge of rail clamp.
13 . Adjust width of support bar as needed until second rail clamp mount is
correctly aligned with second rail clamp.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 11 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
14.Lower rail clamp mount onto rail clamp. Rail clamp mount should slide over rail
clamp. Do NOT Force. Rail clamp mount is not installed properly until
green is visible through indicator slot and pin is flush with top (Both
Circled)
3.0 EQUIPMENT SETUP AND USE
15.Ensure there is No Gap between
the Beach Chair and the OR table
pad. Ensure blue foam roll is
hanging below the Beach Chair.
16.Tighten both rail clamp mount
knobs by turning clockwise.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 12 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
17.Tighten width extension knob by turning it clockwise (to the right).
18.Replace shoulder panels by hooking the latches around the head positioner
tubes, and swinging the panel forward as shown. Engage shoulder panel locks
by turning it outward.
LOCKED
UNLOCKED

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 13 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
19. Adjust lateral position of Beach Chair by gently sliding it near the base along
support bar until desired position is achieved.
20. Turn Beach Chair release handle to the right or left. Lower Beach Chair
slowly until it lies horizontal, flush with the OR Table pad. Use head positioner
handle to assist in lowering.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 14 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
21. Transfer patient onto table in supine
position. Ensure patients hip is located
as shown in image.
(ALIGNED WITH EDGE OF O.R. TABLE)
22. Ensure patient’s head is placed
on the intubation pad as shown
below. Perform necessary
anesthetization and intubation.
23. Open head positioner tube release as shown below.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 15 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
24. Extend head positioner tubes by grasping the handle at the top of the
tubes and pulling gently outward. Be sure to keep intubation pad in place
and monitor the patient’s head during this process.
25. Slide patient head positioner onto head
positioner tubes.
26. Lift patient’s head and remove intubation pad. Slide head positioner forward
and place the patient’s head in the device.
Ensure that patient’s head and neck are always fully supported.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 16 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
27. Secure patient’s head into the
head positioner as dictated by
the device user instructions.
28. Ensure head positioner tubes
are extended at ≥8” (20cm)
above head positioner.
≥ 8” (20cm)
29. Lock head positioner tubes by engaging head positioner tube release as
shown below.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 17 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
31(a). Place OR Table into 5°-10° of
Trendelenburg. Monitor the patient’s
head and neck during adjustments.
31(b). While holding head positioner tube handle, unlock Beach Chair release
handle (shown in step 20) and raise Beach Chair and patient approximately
45°. Monitor the patient’s head and neck during adjustments.
There are 4 simple steps to achieving the modified Fowler Position
(the “Beach Chair” position)
30. Place nonoperative arm in restraint pad
as shown.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 18 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
31(c). Flex OR Table to achieve flexion in
the knee (10°-30° of flexion is
desirable) Monitor the patient’s head
and neck during adjustments.
31(d). Raise Beach Chair until desired angle
is achieved. Monitor the patient’s
head and neck during adjustments.
32.Unlock and remove shoulder panels from operative side of patient as shown below.
Be sure to support the patient and arm to avoid unwanted movement.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 19 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
34. Use headrest lock if needed.
Slide headrest lock below head
positioner and tighten knob.
33. Apply counter traction device to non-operative side of patient using a strap or
brace. Be sure to follow the device user instructions.

Hill Rom SAS
B.P. 14 Z.I. du Talhouet
56330 Pluvigner, France
Tel. [phone]
Fax. [phone]
INSTRUCTIONS FOR USE
Page 20 of 126
Distributed By:
Arthrex, Inc.
1370 Creeside Blvd.
Naples, FL 34108, USA
1-[phone]
Arthrex GmbH
Erwin-Hielscher-Strasse 9
81249 München, Germany
[phone]
D-720667-A3 22 APR 2015
3.0 EQUIPMENT SETUP AND USE
3.4 REMOVAL AND STORAGE
1. Remove counter traction device, arm supports, or other restrain devices from
patient.
2. Ensure head positioner lock is unlocked
and free floating.
3. Reverse steps 28-30 to return patient to horizontal position.
Monitor the patient’s head and neck during adjustments.
4. Remove patient’s head from the head positioner. While supporting the patient’s
head. Remove head positioner from head positioner tubes, and replace
intubation pad before placing patient’s head down.
5. Remove patient from device and remove Beach Chair from OR table by
reversing steps 11-18.