Artos Ryton MR06545W User manual

www.artos-westover.com
Installation Guide
Ryton Towel Warmer MR06545W ( h ardwired version )

The Ryton Towel Rack is intended for towel warming/drying, auxiliary heating or as a
decorative product.
The average heat up time is about thirty minutes, but would depend on
a)the size of the unit and
b)the initial temperature of the unit.
Typically the unit is programmed to be on an hour before expected use and remain on for
an hour afterwards.
The running cost of the towel rack, is usually similar to the running cost of lights in the
same room.
Clean with a soft cloth and use non abrasive cleaners.
Do not connect heater to the network before having read and understood the following
instructions.
Electrical and plumbing connections must be carried out by qualified personnel and the
unit should be securely mounted to the wall in a vertical position and such that it will not
fall into water if the brackets should loosen. Check with local regulations to verify whether
a GFI is required or not. The following pages are to assist in installation.
In case of damages or failures of the rail/connection, the towel rail should be returned to
the manufacturer or their distributor. The warranty from the manufacturer is NOT VALID
in case of improper use or installation. Product designed for use in Canada and USA on-
ly.
See page 4 for detailed installation steps.
USE
INSTALLATION

TECHNICAL SPECIFCATIONS
Rev 04/11
MODEL# MR06545
ELECTRIC VERSION Element
specifications 200W, 110V, 48” cord,
UL approved. Hardwire Kit CSA-US
approved. File ref: 229718
HYDRONIC VERSION Heat ouput
1385 BTU. ½” BSPT tappings.
Steel towel warmers should only
be used in a closed water system,
incorporating a rust inhibitor.
CARE & MAINTENANCE A periodic
wash using warm water and a soft
cloth will retain the high quality finish
of your towel warmer for many years
to come. ON NO ACCOUNT should
any household bleaches, detergents,
abrasive polish, steel wool or similar
cleaning agents be used on this
product.
WALL FIXING Towel warmer
brackets must be securely fastened
to either masonry, wall studs or
plywood board in accordance with
the fitting instructions.
PACKAGING Packaged for regular
UPS type shipping.
WARRANTY 5 years on the frame—
5 years on the heating element
4.0”
25.6”
17.7”
Centre Point for Wire Cover Back Box
15 5/8” bracket centers
(approximate)
4” from end to bracket center (approximate)
NOTE: Towel warmer must be installed so that electrical cord comes out
of the BOTTOM RIGHT of the unit.

INSTALLATION STEPS
1. Check that all the installation pack contents have been received. There should be 2
items as shown below plus optional timer if ordered separately:
2. DISCONNECT POWER SUPPLY. If using a timer, connect timer to power supply. The
timer can be placed anywhere in the room ( recommended beside the light switches ) .
Refer to instructions provided with timer for wiring details.
3. Determine location of towel warmer and provide a single gang electrical box 4 ” below
bottom right of towel warmer ( see spec. sheet ) . Note: where possible, attach at least
two of the brackets to a firm wall stud.
4. Attach the smaller tube to the towel warmer with the smaller bolts provided using diagram
1 below as a guide.
Brackets Hardwire Kit Timer ( optional )
Larger tube
Smaller tube
Diagram 1 Locking screw

INSTALLATION STEPS
5. Determine the wall location of larger tube by measuring the brackets attached to towel
warmer or by using the spec sheet as a guide. Attach larger tube to wall with hole for
locking screw facing down on the bottom brackets and facing up on the top brackets.
6. Feed the wire from the towel warmer through the tube from the hardwire kit, and slide wall
plate onto the tube.
6. Attach upper brackets with locking screw #7, leaving lower brackets free at this time.
7. Connect wire from towel warmer to the wire in the electrical box.
8. Push tube up towel warmer cord, over plastic sleeve, until it touches the hexagonal
chrome collar.
9. Push towel warmer onto the bottom brackets and screw mounting plate to the outlet box
using the screws provided.
10.Insert lower locking screws ( #7 ) .
11.Reconnect power supply. If using a timer, program timer using the instructions provided
with the timer. Towel warmer will take approximately 30 minutes to heat up to full temper-
ature.
12.ENJOY!

CARE & MAINTENANCE
For best results, keep the following in mind to retain the high quality finish of your ARTOS towel
warmer:
• Use a soft, dampened sponge or cloth.
• On no account shout you use an abrasive material such as a brush, scouring pad or steel wool to
clean surfaces.
• Polishwith a soft dry cloth
WARRANTY
This warranty covers against defective products for a period of five years. Under the warranty we will
provide replacement components or products at our discretion. Damage caused by accident, misuse,
abuse, improper installation, improper cleaning or alteration will void the warranty. . Westover, Inc is
not responsible for labor charges, installation or other incidental or consequential costs.
PLEASE REGISTER THIS PRODUCT ONLINE AT WWW.ARTOS-WESTOVER.COM
Item №: MR06545W-
Serial №