Artos Ryton MR12060P User manual

www.artos-westover.com
Installation Guide
Ryton Towel Warmer MR12060P ( plug-in version)

The RytonTowel Rack is intended for towel warming/drying, auxiliary heating or as a dec-
orative product.
The average heat up time is about thirty minutes, but would depend on
a)the size of the unit and
b)the initial temperature of the unit.
Typically the unit is programmed to be on an hour before expected use and remain on for
an hour afterwards.
The running cost of the towel rack, is usually similar to the running cost of lights in the
same room.
Clean with a soft cloth and use non abrasive cleaners.
Do not connect heater to the network before having read and understood the following
instructions.
Electrical and plumbing connections must be carried out by qualified personnel and the
unit should be securely mounted to the wall in a vertical position and such that it will not
fall into water if the brackets should loosen. Check with local regulations to verify whether
a GFI is required or not. The following pages are to assist in installation.
In case of damages or failures of the rail/connection, the towel rail should be returned to
the manufacturer or their distributor. The warranty from the manufacturer is NOT VALID
in case of improper use or installation. Product designed for use in Canada and USA on-
ly.
See page 4 for detailed installation steps.
USE
INSTALLATION

TECHNICAL SPECIFCATIONS
Rev 04/11
MODEL# MR12060
ELECTRIC VERSION Element
specifications 300W, 110V, 48” cord,
UL approved. Hardwire Kit CSA-US
approved. File ref: 229718
HYDRONIC VERSION Heat output
2305 BTU. ½” BSPT tappings.
Steel towel warmers should only
be used in a closed water system,
incorporating a rust inhibitor.
CARE & MAINTENANCE A periodic
wash using warm water and a soft
cloth will retain the high quality finish
of your towel warmer for many years
to come. ON NO ACCOUNT should
any household bleaches, detergents,
abrasive polish, steel wool or similar
cleaning agents be used on this
product.
WALL FIXING Towel warmer
brackets must be securely fastened
to either masonry, wall studs or
plywood board in accordance with
the fitting instructions.
PACKAGING Packaged for regular
UPS type shipping.
WARRANTY Frame 5 years –
Heating element 5 years.
8 7/8” from end to bracket center (approximate)
23.6”
47.2”
21 3/4” bracket centers
(approximate)
NOTE: towel warmer MUST be mounted such that element
cord comes out of bottom right of unit.

INSTALLATION STEPS
1. Check that all the installation pack contents have been received. There should be 1 item
as shown below plus the towel warmer.
2. Determine location of towel warmer near an electrical outlet. The towel warmer cord is
4 ’ long. Note: where possible, attach at least two of the brackets to a firm wall stud.
3. Attach the smaller tube to the towel warmer with the smaller bolts provided using diagram
1 below as a guide.
Brackets
Larger tube
Smaller tube
Diagram 1 Locking screw

INSTALLATION STEPS
5. Determine the wall location of larger tube by measuring the brackets attached to towel
warmer or by using the spec sheet as a guide. Attach larger tube to wall with hole for
locking screw facing down on the bottom brackets and facing up on the top brackets.
6. Insert the smaller tubes ( attached to towel warmer ) into larger tubes and fasten with
locking screws #7.
7. Plug-in towel warmer, allow approximately 30 minutes to heat up to full temperature.
8. ENJOY!

ARTOS Towel Warmer Warranty
®
Item №: MR12060P-
Serial №:
This warranty covers against defective product for a period of five years. If a heating element is
installed, this is covered for a period of five years.
Under the warranty we will provide replacement components or product at our discretion.
Westover, Inc is not responsible for labor charges connected with removal or installation.
PLEASE REGISTER THIS PRODUCT ONLINE AT WWW.ARTOS-WESTOVER.COM