ASA Electronics iN-Command JRVCS1 User manual

GETTING STARTED
Safety Lockout Connecting the DC to the BCM
StartPrime
UnLock
Travel Lock On
032.3 hrs
13.6 VDC
Awning 1
Kitchen Slide
Master Bed Slide
Sofa Slide Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Water Pump Water Heater Interior Lights Exterior Lights Security Lights
Menu
iN•Command® is equipped with a Safety Lockout feature to ensure certain system
functions are unavailable during transit. When the Brake signal or the Tow signal is
activated, iN•Command® will lock down all motorized functions. The DC and mobile
devices will display “Travel Lock On” in red letters and aected buttons will display
“Disable”. To turn the Travel Lock o, the “Unlock” button on the DC inside of the RV
must be pressed.
Continue
www.asaelectronics.com/incommand
The iN•Command® system is comprised of two parts,
the DC (Display Commander or touch pad) and the
BCM (Body Control Module or main control board).
To turn on the DC, hold the power button until the
screen ashes. When the DC is on, the EULA (End
User License Agreement) screen will display - scroll
to the bottom of the screen and select “Accept”.
The DC should then connect to the BCM and “Connecting
to BCM” will appear momentarily. Next, the Passcode
screen will appear. Select “Change passcode” and enter
a four-digit code you will remember. This passcode will
allow the user access into the iN•Command® interface
to change and/or monitor multiple functions of the RV.
The DC should then connect to the BCM, and the HOME
screen will display.
Get the app
Download the iN•Command® app
to turn your mobile device into the
denitive RV Controller.

Pairing an Android or iSO DeviceProgramming Floorplan on Device
QRGINCOMMAND1116
MA-1612001A-1R
For owner’s manual and software updates please visit http://www.asaelectronics.com/incommand.
For update instructions, please refer to Software Update section starting on page 22 in the owner’s manual.
For further assistance, please call 877-845-8750.
Patent # (D776,068)
Patent # (D762,644)
MODEL NUMBER: JRVCS1
©Copyright 2016 ASA Electronics, LLC NOTE: Some features may not be available depending on installed factory options.
StartPrime
032.3 hrs
13.6 VDC
Awning 1
Kitchen Slide
Master Bed Slide
Sofa Slide
In
In
In
In
Out
Out
Out
Out
Water Pump Water Heater Interior Lights Exterior Lights Security Lights
Menu
On the DC, scroll to the bottom of the list of functions and select the MENU
button, then select the Bluetooth button.
Yes
Yes
Yes
Yes
Yes
No
Fuel Station
Master Bed Slide
Sofa Slide
Generator
Menu
Menu
Yes
Awning 1
Yes
Awning 2
Yes
Hydraulic Slide Room
Setup
Info
Brightness
Reset
Passcode
Bluetooth
Status
ANDROID devices
On the DC, select “DISCOVER”, then
select “ALLOW”. “Discover” will turn into
“End” and start counting down. The
iN•Command® ID will appear in “Unpaired
Devices” on the device. Select the correct
ID. The PAIRING REQUEST screen will show
on the DC and device. Select “Pair” on both.
iOS devices
In the Bluetooth Screen on the DC, select Scan. On the iOS Device, go
to Settings, then Bluetooth, and turn it on. The iOS Device will appear
on Unpaired Devices list. Select it. The Pairing Request screen will
appear on the DC and Device. Select “Pair” or “OK” on both. On the
iOS Device, ensure the DC is Connected. If not, press “Not Connected”
next to the DC ID and it should connect.
(Procedure is same for both iOS
and Android devices)
On the device, select the “MENU” button. In MENU, select the “RESET” button; select
“FLOOR PLAN”. The button layout should now reect the oor plan of the RV.
iN•Command® is able to pair to Android and iOS devices using the iN•Command® App. Visit the Google Play and Apple stores on your mobile device to check compatibility
of your device. The rst time the App is opened, the EULA screen will apper. Scroll through the EULA screen and press Accept. Then enter a New Passcode.