Astonica 50100765 User manual

For warranty information, please refer to the back page of
this instruction manual.
270809rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
Limited Warranty
World Factory，Inc．Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS，WITHOUT CHARGE，WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP．ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
Made in China
Distributed by：
World Factory，Inc．
Irving，TX 75063
Model No：50100765
Stone Ridge Swivel Rocker
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.

"U" BAR
WASHER
BOLT
METAL PLATE
SPRING WASHER
NUT
FOOT CAP
STEEL SPRING PLATE
ROCKER ASSEMBLY
SWIVEL BASE
PARTS LIST
ITEM DESCRIPTION QUANTITY
Carefully remove the contents from the package．If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed．
ASSEMBLY INSTRUCTIONS
A Chair Frame 1
B Swivel Base & Rocker Assembly 1
C 5/16＂X25MM Bolt 4
D 8.5X2.0MM Spring Washer 4
E 4
F 5/16＂Nut ４
G Metal plate 2
H Hex Wrench-1 1
I Hex Wrench-2 1
NOTE：This product is intended for residential，non－commercial use．
Parts Detail
AB
CD
EF
GHI
１２
Figure 1
8.5X1.5MM Washer
Step 1: Identify all parts packed in carton against the parts list. Remove all protective materials.
Place parts on a non-abrasive surface to avoid scratching.
Step 2: Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the
rocker assembly is positioned all the way into the base. It may have shifted or vibrated
out during shipment.
Step 3: Important: We recommend 2 people work together to assemble the chair. Note the
arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of
the rocker plate. Point the open end of the horseshoe away from you. The arrows on
the rocker assembly should be pointing towards you. Set the chair frame on the rocker
assembly with front of the seat facing you and the arrows on the "U" bar pointing
towards you ( See diagram). This is very important for a safe, balanced rocking motion.
If chair frame has been properly positioned on the rocker assembly, all arrows on
the "U" bar and rocker assembly will be pointing in the same direction.
Step 4: Critical Step: The two metal plates must be installed in the proper location. Read this
step and carefully examine the diagram. Guide the bolts and washer through the holes in
the "U" bar, through the holes in the steel spring plate, through the hole in the metal plate,
beneath the steel spring plate, add a spring washer and a nut to each bolt as shown in the
diagram. Hand tighten nuts 3-4 revolutions only. Repeat the same procedure on the
other side.
CAUTION: Failure to place metal plates under the rocker plates and above the "U"
bar exactly as shown in diagram will cause the bolt heads and nuts to damage the
structure of the rocker plates and the "U" bar. Damage due to over tightening of
bolts or improper assembly could cause injury and may void your warranty.
Step 5: Tighten all nuts and bolts with the hex wrenches provided. Do not over tighten.
Remove arrow labels from "U" bar and rocker assembly.
Step 6: Your chair should be ready for use. If your chair is not rocking properly, double-check
your assembly procedure, especially Step 3. If the chair rocks too far forward to or is
difficult to rock backwards, you have probably installed the seat frame backwards on the
rocker assembly. If you need further assistance.