Astonica 50105550 User manual

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
270905rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
Limited Warranty
World Factory, Inc.®Products for Home Use
World Factory, Inc.®(Seller) warrants to the original Buyer only, that each Astonica®Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.®authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
®
Made in China
©2005 World Factory, Inc.
Distributed by:
World Factory, Inc.
Coppell, TX 75019
Model No: 50105550
Caldwell Side Table
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.

ASSEMBLY INSTRUCTIONS
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
A
BA C
D
H I J
FE
Figure 1
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
G
C
D
B
E
G
I
F
H
I
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A Glass Top 1
B Table Rim 1
C Table Leg 4
D Leg Connector Bracket 1
E Short Bolts 8
F Long Bolts 8
G Metal Washers 8
H Lock Washers 8
I Plastic Bolt Cap 16
J Hex Wrench 1
Parts Detail
NOTE: This product is intended for residential, non-commercial use.
 CAUTION: Do not over tighten fasteners.
1 (SEE FIGURE 1) Place glass top (A) aside is a safe place until the table
 has been fully assembled.
2. Place the table rim (B) upside down on flat non-scratch surface.
3. Turn one table leg (C) upside down and align leg with corner of table rim (B).
4. Place metal washer (G) onto short bolt (E) and insert into previously drilled hole.
 Using hex wrench (J) attach leg to table rim. Repeat steps 2 and 3 for remaining table legs.
 Do not tighten hardware.
5. Place leg connector bracket (D) between table legs (C).
6. Place lock washer (H) onto long bolt (F) and insert into previously drilled holes of connector
 bracket and table leg. Using hex wrench (J) attach connector bracket to each leg. Do not
 tighten hardware.
7. With each leg attached to the connector bracket tighten each bolt a few revolutions at a time,
 alternating between bolts in a cross corner "X" fashion.
NOTE: Tightening every other bolt or in a cross fashion will ensure your table is level by
 placing equal pressure on each joining bolt.
8. Cover all bolts with plastic bolt cap (I).
9. Turn table frame upright and carefully place the glass top (A) into table rim (B).
10.Adjust table legs as needed using the glides at bottom of each leg. Turn glides by hand until
 table is level to the floor.
 Your table is now ready to use.
12