ECONOMY AIR UNDERCOAT GUN
• Applies a top quality undercoat to vehicles to fight rust and
stone chips
• Applies all popular brands of undercoat in any viscosity
• Unit comes with 2 tubes:
- 3-1/4" Long with 5/16" ID
- 7-1/4" Long with 1/4" ID
• Cap Thread Pitch: 1-3/4" x 6 UNS
• Quick disassembly for faster cleanups
• Weight: 0.65lbs
Page 1
4538
When unpacking, check the parts diagram and part number
listing on page 2 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
www.astrotools.com
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
• Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year (except where noted on our
price schedule) from the date of 1st use. Astro reserves the right to determine
whether the product failed because of defective material, workmanship or other
causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its
discretion, will repair products covered under this warranty free of charge. The
distributor should direct the original user to return the product (with the exceptions
listed below) with the distributor’s name, address, adequate proof of date of
purchase or a copy of warranty card, and a short note explaining the problem.
Failures caused by accident, alteration, or misuse are not covered by this
warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
1 YEAR LIMITED WARRANTY
Study, understand and follow all instructions provided with this product.
Read these instructions carefully before installing, operating, servicing
or repairing this tool. Keep these instructions in a safe accessible place.
Check gun and trigger prior to use to ensure unit is not damaged in any
way. It is recommended to use ANSI approved hearing safety protection
equipment
• Use of this product can expose you to chemicals such as
phthalates which are known to the State of California to
cause cancer, and birth defects or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov/product.
Always wear appropriate safety equipment and clothing
when using this product. Study, understand and follow all
instructions provided with this product. Failure to read and
follow all warnings and operating instructions may result in
damages and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
•Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
•Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
PRODUCT INFORMATION:
This unit is designed to dispense undercoat material of
varied viscosity. Do not use this tool outside of the designed
intent. Never modify the tool for any other purpose or use.
INTENDED USE OF THE TOOL
WARNING
DO NOT DISCARD – GIVE TO USER
WARNING
1. Inspect gun prior to use to ensure unit is not damaged
in any way.
2. Attach the product being sprayed to the gun.
3. Connect the air inlet connector to the air source.
4. Press trigger and begin dispensing product.
5. When the job is completed make sure to close air source.
6. Clean unit before storing.
ECONOMY AIR UNDERCOAT GUN APPLICATION:
MADE IN CHINA
