DO NOT DISCARD – GIVE TO USER
WARNING
www.astrotools.com
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
Page 1
Model: Product Type:
When unpacking, check the parts diagram and part number
listing on page 2 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing,
operating, servicing or repairing this tool. Keep these instructions
in a safe accessible place.
INTENDED USE OF THE TOOL
94222 13" INTERNAL / EXTERNAL
SNAP RING PLIERS
13" INTERNAL / EXTERNAL SNAP RING PLIERS
PRODUCT INFORMATION:
SPECIFICATIONS:
MADE IN CHINA
• Includes Internal and External straight and 90
degree bent pliers with a 0.90" (2.3mm) tip size
• Made from hardened Chrome Vanadium with black
and polished finish and dipped non-slip handles
• Professional fit and finish
13" Internal Circlip Pliers, Bent Nose - 0.090"
13" Internal Circlip Pliers, Straight Nose - 0.090"
13" External Circlip Pliers, Straight Nose - 0.090"
13" External Circlip Pliers, Bent Nose - 0.090"
1 YEAR LIMITED WARRANTY
This tool is used for removing or installing internal or
external design circlips/snap rings.Do not use this tool
outside of the designed intent. Never modify the tool for
any other purpose or use. • Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the right to determine whether the
product failed because of defective material, workmanship or other causes and to
charge back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair
products covered under this warranty free of charge. The distributor should direct the
original user to return the product (with the exceptions listed below) with the
distributor’s name, address, adequate proof of date of purchase or a copy of warranty
card, and a short note explaining the problem. Failures caused by accident,
alteration, or misuse are not covered by this warranty.
• If one part of this product fails, please do not return the entire product. Astro
will replace free of charge component parts of this product that fail within 1
year of first use by the original user. Items included in this category include
but are not limited to kits, hand tool kits and any other product where there are
multiple items or components that make up the unit. Please contact the phone
number below in order to obtain the replacement components covered under
warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do not
allow the exclusion of limitations of incidental or consequential damages so the above
limitations may not apply to you.
• Use of this product can expose you to chemicals including
ethylene glycol, gasoline vapors and engine exhaust, which
are known to the State of California to cause cancer, birth
defects, or reproductive harm. For more information, visit
www.P65Warnings.ca.gov. Always wear ANSI approved
safety equipment, safety glasses and clothing when using
this product. Study, understand, and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
•Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
•Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
WARNING
