Asus Aaeon UP Xtreme i11 EDGE User manual

Last Updated: October 13, 2022
UP Xtreme i11 EDGE
Maker Board System
UPX-EDGE-TGL01
User’s Manual 2nd Edition

Preface ii
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Copyright Notice
This document is copyrighted, 2022. All rights are reserved. The original manufacturer
reserves the right to make improvements to the products described in this manual at
any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any
form or by any means without the prior written permission of the original
manufacturer. Information provided in this manual is intended to be accurate and
reliable. However, the original manufacturer assumes no responsibility for its use, or
for any infringements upon the rights of third parties that may result from its use.
The material in this document is for product information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, AAEON assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information contained herein
AAEON reserves the right to make changes in the product design without notice to its
users.

Preface iii
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Acknowledgements
All other product names or trademarks are properties of their respective owners.
⚫Microsoft Windows and Windows 10 are registered trademarks of Microsoft
Corp.
⚫Intel® and Celeron® are registered trademarks of Intel Corporation
⚫Intel Core™ is a registered trademark of Intel Corporation
⚫Ubuntu is a registered trademark of Canonical Ltd.
⚫Yocto and Yocto Project are registered trademarks of the Linux Foundation
⚫Linux is a registered trademark of Linus Torvalds
No ownership is implied, inferred or assumed for products, names or trademarks not
herein listed by the publisher of this document.

Preface iv
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Packing List
Before setting up your product, please make sure the following items have been
shipped:
Item
Quantity
UP Xtreme i11 EDGE System
1
If any of these items are missing or damaged, please contact your distributor or sales
representative immediately.

Preface v
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
About this Document
This User’s Manual contains all the essential information, such as detailed descriptions,
and explanations on the product’s hardware and software features (if any), its
specifications, dimensions, jumper/connector settings and definitions, and driver
installation instructions (if any) to facilitate users in setting up their product
Users may refer to the product page at AAEON.com for the latest version of this
document.

Preface vi
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Safety Precautions
Please read the following safety instructions carefully. It is advised to keep a printed
copy of this manual in an easy to access location for reference.
1. All cautions and warnings on the device should be noted.
2. Make sure the power source matches the power rating of the device.
3. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
4. Always completely disconnect the power before working on the system’s
hardware.
5. No connections should be made when the system is powered as a sudden rush
of power may damage sensitive electronic components.
6. If the device is not to be used for a long time, disconnect it from the power
supply to avoid damage by transient over-voltage.
7. Always disconnect this device from any AC supply before cleaning.
8. While cleaning, use a damp cloth instead of liquid or spray detergents.
9. Make sure the device is installed near a power outlet and is easily accessible.
10. Keep this device away from humidity.
11. Place the device on a solid surface during installation to prevent falls
12. Do not cover the openings on the device to ensure optimal heat dissipation.
13. Watch out for high temperatures when the system is running.
14. Do not touch the heat sink or heat spreader when the system is running
15. Never pour any liquid into the openings. This could cause fire or electric shock.
16. As most electronic components are sensitive to static electrical charge, be sure
to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and contain all electronic components
in any static-shielded containers.

Preface vii
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
17. If any of the following situations arises, please the contact our service personnel:
i. Damaged power cord or plug
ii. Liquid intrusion to the device
iii. Exposure to moisture
iv. Device is not working as expected or in a manner as described in
this manual
v. The device is dropped or damaged
vi. Any obvious signs of damage displayed on the device
18. DO NOT LEAVE THIS DEVICE IN AN UNCONTROLLED ENVIRONMENT WITH
TEMPERATURES BEYOND THE DEVICE’S PERMITTED STORAGE TEMPERATURES
(SEE CHAPTER 1) TO PREVENT DAMAGE.

Preface viii
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
FCC Statement
This device complies with Part 15 FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received including interference that may cause
undesired operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions and your local government’s recycling or
disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le
constructeur. Recycler les batteries usées en accord avec les instructions du fabricant et
les directives gouvernementales de recyclage.

Preface ix
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
China RoHS Requirements (CN)
产品中有毒有害物质或元素名称及含量
AAEON System QO4-381 Rev.A0
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联
苯(PBB)
多溴二苯
醚(PBDE)
印刷电路板
及其电子组件
×
○
○
○
○
○
外部信号
连接器及线材
×
○
○
○
○
○
外壳
○
○
○
○
○
○
中央处理器
与内存
×
○
○
○
○
○
硬盘
×
○
○
○
○
○
液晶模块
×
×
○
○
○
○
光驱
×
○
○
○
○
○
触控模块
×
○
○
○
○
○
电源
×
○
○
○
○
○
电池
×
○
○
○
○
○
本表格依据 SJ/T 11364 的规定编制。
○ ：表示该有毒有害物质在该部件所有均质材料中的含量均在
GB/T 26572标准规定的限量要求以下。
×：表示该有害物质的某一均质材料超出了GB/T 26572的限量要求，然
而该部件
仍符合欧盟指令2011/65/EU 的规范。
备注：
一、此产品所标示之环保使用期限，系指在一般正常使用状况下。
二、上述部件物质中央处理器、内存、硬盘、光驱、电源为选购品。
三、上述部件物质液晶模块、触控模块仅一体机产品适用。

Preface x
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
China RoHS Requirement (EN)
Hazardous and Toxic Materials List
AAEON System QO4-381 Rev.A0
Component
Name
Hazardous or Toxic Materials or Elements
Lead (Pb)
Mercury (Hg)
Cadmium (Cd)
Hexavalent Chromium (Cr(VI))
Polybrominat ed biphenyls (PBBs)
Polybrominat ed diphenyl ethers (PBDEs)
PCB and
Components
X
O
O
O
O
O
Wires &
Connectors for
Ext.Connections
X
O
O
O
O
O
Chassis
O
O
O
O
O
O
CPU & RAM
X
O
O
O
O
O
HDD Drive
X
O
O
O
O
O
LCD Module
X
X
O
O
O
O
Optical Drive
X
O
O
O
O
O
Touch Control
Module
X
O
O
O
O
O
PSU
X
O
O
O
O
O
Battery
X
O
O
O
O
O
This form is prepared in compliance with the provisions of SJ/T 11364.
O: The level of toxic or hazardous materials present in this component and its parts
is below the limit specified by GB/T 26572.
X: The level of toxic of hazardous materials present in the component exceed the
limits specified by GB/T 26572, but is still in compliance with EU Directive
2011/65/EU (RoHS 2).
Notes:
1. The Environment Friendly Use Period indicated by labelling on this product is
applicable only to use under normal conditions.
2. Individual components including the CPU, RAM/memory, HDD, optical drive,
and PSU are optional.
3. LCD Module and Touch Control Module only applies to certain products which
feature these components.

Preface xi
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Table of Contents
Chapter 1 - Product Specifications ......................................................................................... 1
1.1 Specifications..............................................................................................................2
Chapter 2 –Hardware Information ....................................................................................... 4
2.1 Dimensions .................................................................................................................5
2.2 Jumpers and Connectors.........................................................................................8
2.3 List of Jumpers and Connectors............................................................................ 11
2.3.1 Power Button (SW1)............................................................................................12
2.3.2 RTC (CN1)..............................................................................................................12
2.3.3 HDMI/ DP Dual Port (CN2)...............................................................................13
2.3.4 eDP (CN3)............................................................................................................ 14
2.3.5 SATA Connector (CN4)......................................................................................15
2.3.6 USB Type A Dual Port (CN8) ............................................................................15
2.3.7 USB Type A Dual Port (CN9) ............................................................................16
2.3.8 USB Type C (CN10) .............................................................................................16
2.3.9 USB 2.0/UART 1x10P Wafer (CN11) ..................................................................17
2.3.10 M.2 2230 E-Key Slot (CN12)..............................................................................18
2.3.11 M.2 2280 M-Key Slot (CN13) ............................................................................19
2.3.12 M.2 3052 B-Key Slot (CN14)..............................................................................21
2.3.13 LAN Dual Port (CN15) .......................................................................................22
2.3.14 PCI Express Slot (CN18).....................................................................................23
2.3.15 40-Pin HAT Connector (CN19)........................................................................24
2.3.16 CPLD and BIOS Update (CN20)......................................................................25
2.3.17 DC Jack (CN21) ...................................................................................................25
2.3.18 Front Panel (CN22) ............................................................................................26
2.3.19 DC Terminal Block (CN23) ...............................................................................26
2.3.20 COM3, COM4 RS232/ 422/ 485 (CN28/CN29)...........................................27
2.3.20.1 COM3 1x10P Wafer RS232/ 422/ 485 (CN28)....................................27
2.3.20.2 COM4 1x10P Wafer RS232/422/485 (CN29) .....................................28

Preface xii
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
2.3.21 ATX Power (CN31)..............................................................................................28
2.3.22 SATA Power (CN32) ..........................................................................................29
2.3.23 Audio Jack (CN33) .............................................................................................29
2.3.24 Fan Connector (J1) .............................................................................................30
2.3.25 AT/ATX Mode Jumper (JP1) .............................................................................30
2.3.26 GPIO Terminal Block...........................................................................................31
2.4 Hardware Assembly ..........................................................................................................32
2.4.1 Wi Fi Module (M.2 2230 E-Key Slot) Installation .........................................32
2.4.2 PCIe Module (M.2 2280 M-Key Slot) Installation.........................................37
2.4.2.1 Reassembling the System ...........................................................................42
2.4.3 5G Module (M.2 3052 B-Key Slot) Installation.............................................44
2.4.4 2.5” SATA Drive Installation .............................................................................49
2.4.5 VESA Mount Installation ...................................................................................53
Chapter 3 –Software Installation......................................................................................... 55
3.1 Linux Setup ...............................................................................................................56
3.2 Windows Drivers Installation.................................................................................56
3.3 Dummy Driver Installation.....................................................................................57
Appendix A –UP Framework SDK Installation ....................................................................61
A.1 Introduction ..............................................................................................................62
A.2 Installation for Windows 10....................................................................................62
A.3 Installation for Windows IoT Core........................................................................65
Appendix B –Cables and Connectors ................................................................................ 67
B.1 Cables and Connectors..........................................................................................68

Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Chapter 1
Chapter 1 - Product Specifications

Chapter 1 –Product Specifications 2
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
1.1 Specifications
System
CPU
11th Gen Intel® Core™ Processor SoC
Core™i7-1185GRE
Core™i5-1145GRE
Core™i3-1115GRE
Celeron® 6305E
Memory
DDR4 SO-DIMM Slot x 2 (up to 64GB
3200MHz)
Graphics
Intel® Iris® Xe Graphics
Storage
SATA Connector x 1 (with Power)
M.2 2280 M-Key NVMe (PCIe [x2])
Ethernet
Intel® i225 IT (TSN) x 1
Intel® i219 (with vPro) x 1
Wi-Fi/Bluetooth
Optional
Audio
Realtek ALC888s x 1 (Mic/Line Out)
USB
USB 3.2 Gen 2 x 3
USB 2.0 x 1 (Type A)
USB4 Type C x 1
Expansion Slot
M.2 2230 E-Key x 1
M.2 2280 M-Key x 1
M.2 3052 B-Key x 1 with SM Slot
SATA III Connector x 1 (with Power)

Chapter 1 –Product Specifications 3
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
I/O
Power
12V DC-In (lockable plug)/ Phoenix
Connector (Optional)
USB
USB 3.2 Gen 2 x 3
USB 2.0 x 1 (Type A)
USB4 Type C x 1
Display Port
HDMI 2.0 x 1
DP 1.4 x 1
eDP x 1, 4K at 60Hz Panel
Ethernet
Intel® i225 IT (TSN) x 1
Intel® i219 (with vPro) x 1
COM Ports
RS-232/422/485 x 2
Environment and Dimensions
Power Supply
12V (AT & ATX)
Dimensions
4.9” x 6” x 2.6” (124 mm x 152 mm x 66.5mm)
Gross Weight
5 lb. (2.3 Kg)
Operating Temperature
32°F ~ 140°F (0°C ~ 60°C)
Operating Humidity
0% ~ 90% relative humidity, non-condensing
Certification
CE, FCC Class A
OS Support
Windows 10, Windows 10 IoT
Yocto 3.1
Ubuntu 20.04

Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Chapter 2
Chapter 2 –Hardware Information

Chapter 2 –Hardware Information 5
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
2.1 Dimensions
System Dimensions

Chapter 2 –Hardware Information 6
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
System Dimensions with fan

Chapter 2 –Hardware Information 7
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
Board Dimensions

Chapter 2 –Hardware Information 8
Maker Board System UP Xtreme i11 EDGE UPX-EDGE-TGL01
2.2 Jumpers and Connectors
UPX-EDGE-TGL01 System: