ATC Tiger Eco User manual

ATC Tiger Eco
High Speed Hand Dryer
Z-3145M Stainless Steel Cover
Z-3145W White Cover
House,
Broomhill drive
Tallaght
D24 EF99
Ireland
IE:003531 4678301
UK:0044 203 564 9164
FAX: [phone]
Email: [email protected]
Precautions before installation
Do not install in the following locations, installation in these areas can
cause the unit to malfunction and could void the warranty on the hand
dryer.
• Areas with temperatures below 0°C and above 40°C
• In direct sunlight, above reective surfaces, or surfaces that radiate
heat - this may cause unwanted operation of the sensor.
• Above Counters or sinks
• Areas of high humidity or moisture levels
• Locations containing Corrosive or Oxidizing gases
• Areas at altitudes above 2000m
Installation Location
Note: If you are replacing the supplied power cable the cord used must
have a cross section of at least 1.5mm² (1.5mm² 2 Core & Earth)
• The chart below shows the recommended mounting height for the
hand dryer.
• Make sure the hand dryer is mounted more than 150mm away
from walls on either side of the dryer to ensure access to the
cover mounting screws.
• Do not mount the dryer behind doors where the opening of the
door may damage the dryer.
• Do not install the dryer with the power connected.
• This hand dryer must be connected by a qualified electrician when it is
being installed.
Circuit Diagram
Environmental Protection
Waste Electrical and Electronic Equipment (WEEE) must
never be placed in any household wheelie bins. WEEE is
taken back free of charge at electrical retail outlets on a
one-for-one like-for-like basis. Local authority civic ameni-
ty facilities also take back WEEE free of charge.
Do not dispose of this hand dryer with household waste.
WARRANTY
ATC Electrical and Mechanical provides a two year limited parts warranty
for the Z-3145M/W hand dryers as long as the unit has been installed,
used and maintained in accordance with the information provided in this
manual.
In order to arrange parts for the hand dryer, the information listed below
is required. It is recommended to write this information below and keep
this instruction manual in a safe place.
Receipt Number:
Date of Manufacturer:
Date of Purchase:
Location of Purchased:

Specification
Voltage 220-240v ~AC Sound Level 70dB(A) @1m
Phase 1Φ Sensor Range 15-20cm (fixed)
Load 550-1200w IP Rating 13
Air Speed 70m/s Size HxWxD (mm) 312x302x172
Heat output Off/650w Net Weight 4.1kg
Component Identification
Packing List
1x Instruction Manual
1x Allen Key
1x ATC Tiger Eco Hand Dryer
4x Plastic Wall Plug
4x Self tapping screws
Daily Use and Maintenance
External Maintenance:
• Regularly clean the cover and sensor with a soft
cloth. Do not use harsh chemicals,abrasive, acid
or alkali based cleaning products as they can
damage the nish of the hand dryer. If using a
chemically impregnated cloth, test on an incon-
spicuous area prior to use to test for suitability.
Internal Maintenance:
• After turning off the power supply remove the
cover and check all connections.
• Clean away any dirt that has deposited inside
the hand dryer
• Remove the Air inlet cover and remove the
lter, clean the lter with a vacuum and replace
the lter in the housing.
• It is recommended to change the lter every 6 -
12 months depending on usage
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
12 3
Method of Operation:
Insert the back
of your hands
Turn your
hands over
Rub your hands
together until dry
Installation Method
First Fix:
A recessed junction box should be
installed to allow the hand dryer to
sit ush to the wall.
The Height of the junction box
should be determined from the
table shown in the installation
location section.
At least 300mm of cable should
be left for nal connection.
Cover Removal:
Remove the Cover Screws on
either side of the hand dryer with
the Allen key provided and retain
screws.
Lift off the cover and store in
a location where it will not be
damaged.
Mounting:
Drill the Mounting holes according
to the template shown overleaf,
and mount the hand dryer with the
provided plastic wall plugs and
screws.
Connect the power cable to the
terminal block and ensure the
correct polarity at the terminals.
Note: The infra red sensor on the Tiger Eco is xed, do not install the
hand dryer in locations where there is anything below the unit as they
can start the dryer. e.g. Radiators, above sinks, above shelves etc.
Replace the cover:
Place the cover over the base plate,
insert the cover screws and tighten
with the Allen Key provided.
Note:
T he Cover is earthed
through the cover mounting
screws. Please ensure that they
are firmly attached prior to
re-energizing the power supply.
Once the Cover is in place, re-ener-
gize the power supply and test the
hand dryer for operation.
Energy Savings
The ATC Tiger Eco is equipped with a heat selection
switch to turn the heating element on and off. In the
warmer months of the year it is recommended that the
element is turned off to reduce the energy use of the
dryer and CO2 levels generated
For additional user protection the installation of a residual current device
(RCD) with a rated residual operating current not exceeding 30mA is
advisable in the electrical circuit supplying the bathroom. Please ask your
installing electrician for advice
Hand dryer
doesn’t start
when hands
are put un-
derneath
If the hand dryer does not start or make any noise
the problem could be the sensor. Check to ensure
the sensor is clean and check the connections to the
PCB. If these do not solve the issue, replace the PCB
and Sensor.
The airow
is not getting
hot
The Tiger Eco is equipped with a switch to turn the
heater on and off; check to see if the element is turned
off. If this is not the case, replace the heating element.
The hand
dryer starts
by itself
The most common cause of self starting is due to
incorrect placement of the dryer. Ensure that there is
nothing below the hand dryer (At least 450mm space)
and check to ensure that there are no reective surfac-
es below to accidentally set off the dryer.
Troubleshooting:
With regular care and maintenance the Tiger Eco hand dryers should give
many years of usage. However, here are some hand dryer issues that
could arise and how to remedy them: