This product is intended for installation bya qualified electrician; please observe all local wiring rules when installing this
product.
Disconnectpowerat the Circuit breaker or main fuse before installing or servicing.
Failure to properly ground unit could result insevere electrical shock and/ordeath.
All units must be supplied with a 3-wire service. The ground wire must be connected to the dryer’s earthing terminal and
back plate.
NOTE
Do not install dryer over a washbasin.
Ifthe power supply cord is damaged, it must be replaced by the manufactureror its service agent or similar qualified
person
inorder to avoida hazard. Means for disconnection must be incorporated in the fixed wiring in accordance
with the wiring
rules
SPECIFICATION
•
Voltage:230V/50Hz,6.1A
•
Rated Power:1400W
•
AirVelocity : 13M/S
•
AirFlow:90M
3
/H
•
Drying Time: 30-40S
•
SensorRange:5-15CM (Manually adjustable)
•
ProtectionLevel:IPX1
•
Stainless Steel ElectricIsolation:CLASS I
•
ABS Electric Isolation CLASS II
•
Finish: Stainless Steel or White ABS
•
Brush Motor:2300 rpm
•
Noise at2M: 60dB
•
Dimensions (HxWxD): 285x225x165mm
INSTALLATION
1. Installation must be carried out in accordance with the current edition of the local wiring regulations. Installation
should be performed only by a qualified electrician.
2. Place template against wall at desired height (see mounting height recommendations below) and mark the
location of the 4 mounting holes. Drill Diameter: 8mm (5/16").
3. Remove and retain the two security hex cover screws and cover. Then mount the hand dryer base on the wall
using the wall plugs and fixings provided
4. Connect the live wire (Brown) to the terminal block marked “L”.
5. Connect the neutral wire (Blue) to the terminal block marked “N”.
6. Connect the ground wire(Colored Green & Yellow) to the terminal block marked “E”.
7. Replace cover. Do not over-tighten screws.
8. Energize the supply and test for sensitivity. If the dryer sensitivity is not satisfactory, remove the cover and
adjust using the sensitivity potentiometer.
Installation Kit Included: 4pc self-threadingscrew, 4pc plastic dowel,1pc installationtemplate
MOUNTING HEIGHTS (to base of the dryer)
Men 1200mm
Women 1160mm
Children 4-7 years
812mm
Children8-10years
860mm
Children11-13years
910mm
Children14-16years
960mm
Disabled Bathroom 900mm
OPERATION
•
Automatic No-touchoperation.
•
Shakeexcess water from hands.
•
Place handsunderthe outlettostart operation.
•
Rub hands lightlyand rapidly.
•
Stopsautomatically after hands are removed.
MAINTENANCE
•
Periodic cleaning of the unit is recommended.
•
Isolate power, remove cover and clean dryer interior. Remove any dust or lint.
•
Wipe the cover with a damp cloth and mild
cleaning solution. Donotsoak.
•
Neveruse abrasives to clean the cover
CIRCUIT DIAGRAM
TROUBLESHOOTING
Symptom
CorrectiveAction
If the dryer will not run
breaker supplying the dryer is operational. If it is,
disconnect the power and remove the dryer cover.
Taking suitable precautions to avoid shock hazard, reconnect the power and
check for voltage at the terminal block.
e is power and the dryer will not run, replace the Electric Circuit Board
Board, and/or Sensor Board. Turn the blower wheel several
by hand to see if it is blocked, if so remove blockage and test dryer
If the dryer cycles by it
runs all the time, or is not
sensitive enough
Ensure that there is no obstruction on or in front of the infrared sensor.
Clean an
y dirt off the sensor lens.
Try adjusting the sensitivity potentiometer
on Microcomputer Board (Blue
dial). Turn anti-clockwise to decrease the
sensor range. If the problem persists, replace the Microcomputer Board
If heat element gets hot but
the fan motor does not turn
Disconnect the power. Remove the dryer cover and check for obstructions
in
the fan housing. Damaged fans must be replaced. If there no obstructions,
replace the motor.
If the dryer runs but makes a
buzzing noise
Disconnect the power. Remove the dryer cover and check the fan for rubbing
on the housing as its rotates. Replace fan
if it is rubbing or damaged.
If the fan motor runs but the
heat element does not get
hot (Dryer blows cold air)
Disconnect the power and remove the dryer cover. Check for loose or
damaged wires. Remove the blower housing.
Check the heating element to
if it is burnt out or broken. Damaged elements must be replaced. If the
element does not appear damaged, disconnect it at the Electric Board and
check element wire continuity
, if open circuit replace the element
Please check thermostat continuity on the heating element at the same
If the motor makes a ticking
or whining noise when it runs
Disconnect the power, remove the dryer cover and check the brushes for
wear, replace them if necessary
WARRANTY
This hand dryerhas a 1 yearwarranty from the date ofpurchase for any manufacturing defect.
Itcovers replacement ofdefective parts except when caused by improper use ofthe hand dryer.
This warranty is only valid if
the form card has been properly filled up with the vendor stamp.
Foranywarranty claimyou should contactyour local distributor or manufacturer.
